Why is the zip on the back of a wetsuit?
These wetsuits are very easy to put on. The back zip makes the opening very wide, so you can quickly get in without any wriggling or making awkward positions. Since they are easy to get into, it is much less likely to hurt yourself while putting them on (Weird arm and leg positions can cause sprains and cramps).
Does the zipper go on the back of a wetsuit?
Easy on/off: The zipper goes way down the back, providing a much wider opening than a front-zip. Adjustable neck tightness: The Velcro closure system around the neck of a back-zip wetsuit allows you to customize the tightness to you preferred level of tension.
How do you fix a stuck wetsuit zipper?
If your zipper is stuck, lubricate the slider with a little Zippy-lube™ or O-ring grease. Wipe off any excess. Don’t use a spray like WD40, as it will be difficult to keep from getting it on the neoprene.
How do you break in a wetsuit?
There isn’t much of a trick to breaking in a wetsuit. You just need to wear it often and move around in it a lot. Just putting on the wetsuit will stretch it out just a bit each time. The areas that will get stretched the most from donning the wetsuit will be the shoulder region of the suit.
How tight should wetsuit be?
How Should a Wetsuit Fit? In general, a wetsuit should fit snugly, like a second skin but not so tight that your range of motion is limited. The sleeves (if full-length) should fall at the wrist bone and the legs just above the ankle bone, and there should be no gaps, pockets, or rolls of neoprene.
How big should the zipper be on a wetsuit?
When the back zipper is closing you want to have a little bit of pull on the neoprene but the zipper gap should not be much more than 1 inch. If the suit fits right it should not be a chore to get into it and when removed after the dive there should be slight impressions in the skin where the seals and stitching were.
Do You Put Your wetsuit on backwards or forwards?
This will make it much easier to put on. Don’t put your wetsuit on backwards! If the zipper is horizontal, then it is a chest zip and goes in the front. If it is a longer vertical zipper with a long pull tab on it, then it is a back zip and goes in the back.
Where do you put the sleeves on a wetsuit?
The sleeves (if full-length) should fall at the wrist bone and the legs just above the ankle bone, and there should be no gaps, pockets, or rolls of neoprene. It is important to understand that after a wetsuit gets wet it will loosen up and feel more comfortable.
Can a wetsuit fit outside of the measurements?
Sometimes you can be outside of the measurements and the suit will still fit, but if you can find a suit where you fall within the measurements that will most likely be the wetsuit for you. How Should a Wetsuit Fit? In general, a wetsuit should fit snugly, like a second skin but not so tight that your range of motion is limited.
What to do if your back zip wetsuit breaks?
When putting on a back-zip suit, hold the bottom of the zipper down with one hand while pulling straight up on the pull cord with the other hand. If your suit has a thumb loop at the bottom of the zipper, use it! Pulling at the zipper on an angle or excessively hard and fast can cause the slider to pull off the track and/or break a zipper tooth.
Where are the Zips located on a wetsuit?
There is a fix to the water penetration problem, a feature generally referred to as the Backwing or Bat-Wing, or zip gusset but different companies use different trademarks to brand the system. Luckily, the principle stays the same- by stitching a panel on the inside of the zip, anchored along the base of the zip up to the shoulders.
What’s the best way to put on a wetsuit?
If your wetsuit has smooth skin neoprene you’ll want to be careful not to use your fingernails at this point. You can start by grabbing the suit near the top of each leg (one at a time) and making sure the suit’s knee pads are right at your knees. Feel free to hold the suit a little lower on the leg if you find that helps.
Why do you need to clean your wetsuit zippers?
Given that wetsuit zippers will be predominantly used outdoors there are plenty of ways that they can become dirty. Keeping zips clean helps them to last longer and work better. After use in the sea, rinse them with fresh water to prevent salt deposits corroding them.
