Why is the flame on my Atwood furnace not working?

It could also be the flame proving circuit. If the flame rod is out of alignmet, or if the flame is not touching the flame rod strongly or if the flame rod is dirty you will get these symptoms. I have also found that a poor ground from the circuit board can cause this as the flame is rectified through the flame to ground.

What kind of electrodes did the Atwood furnace have?

3–Atwood had two types of electrodes for ignition—If you have two wires going to electrode—one is ignition–other is temperature sensor (that tell circuit board there is a flame).

What’s the flame on an Atwood fifth wheel?

Atwood Hydro Flame 8940 in a fifth wheel. Turns on OK, fan starts, gas ignition occurs. Stays lite for about 5 seconds and then goes out, lites again in about 10 seconds. Continues this cycle until turn the stat down. Does not provide enough heat to maintain temp.

What does the sail switch on an Atwood furnace look like?

Sail Switch, can’t describe where it is or what it look like, but that is the symptoms of it going bad. If the sail switch was bad, it would never allow the burner to ignite. The following is from the Atwood manual, and this is assuming the blower never turns off, and the burner is igniting, then shuts off, then ignites again, over and over again:

What’s the problem with my Atwood 8500 heater?

The furnace has been causing us problems for some time and hoping someone can offer some help in finding the problem. When the furnace is turned on, the fan runs and then a short time later the furnace fires and begins to heat. The furnace works fine and heats to the temperature set on the thermostat.

Where can I find the Atwood furnace manual?

Atwood manual for furnaces with wiring diagrams. See if you can use this manual to help troubleshoot the problem.

3–Atwood had two types of electrodes for ignition—If you have two wires going to electrode—one is ignition–other is temperature sensor (that tell circuit board there is a flame).

Why does my Atwood Excalibur furnace not stay lit?

Hi. I have an Atwood Excalibur 8500 III hydro flame furnace. It comes on and the burner ignites but it won’t stay lit. It “attempts” to light the death, turn it off, or the battery runs down). wheel etc. I found that the blower housing had a missing screw which would cause low static pressure.

Why does my furnace keep cycling on and off?

If the furnace keeps cycling on and off despite the temperature meeting then there is some problem with the furnace functioning. This can be caused if the furnace vents are blocked. Check for the furnace box, see if there is anything that is blocking the furnace vents.

What happens if my Atwood flame furnace stops working?

That means if you fail to get the RV furnace back to work, it would get very cold later tonight. In the case you don’t want to get sick due to low temperatures, this troubleshooting guide is for you. Everything you need to know Atwood hydro flame furnace including working principles, problem symptoms and more are presented downs below.

Why is there no heat coming out of my gas furnace?

Check the propane level in your tanks. The furnace blower may be able to start, but there will be no heat coming out because there is no gas to ignite the burner. A tank with very little gas or an issue in the gas line can lead to low gas pressure. This will result in no heat from the furnace or lack of a constant pilot light.

How to troubleshoot a travel trailer gas furnace?

Many new RV furnaces have replaced the pilot light with a direct spark ignition system. If your furnace is struggling to keep the pilot light lit, check the thermocouple to make sure it’s positioned correctly. A malfunctioning regulator on your propane tank could also result in an irregular pilot light.

What are the most common RV furnace problems?

common rv furnace problems include the furnace wont light, it wont heat properly or it could cycle on and off. Furnace could also make nosie. common rv furnace problems include the furnace wont light, it wont heat properly or it could cycle on and off. Furnace could also make nosie.

How to repair an Atwood 8535 hydro flame?

If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: LrrpF7jRmkniSwW6)

How many Atwood 8535’s are left in stock?

Only 2 left in stock – order soon. . Only 17 left in stock – order soon. . Only 5 left in stock – order soon. . Only 3 left in stock – order soon.

What does ignition lockout fault mean ref : Atwood furnace model?

Second opinion] Hi Steve, I’m GuyAtwood AFM D35131 furnace give Ignition Lockout Fault. Electrode was adjusted 3/8″ above the burner screen and the ground probe 1/8″ from the electrode. The furnace ig…

Is the Atwood 7920-ii PDX RV dual sense?

*NEITHER OF THESE KITS ARE APPLICABLE TO A 7920, ONLY TO A 7920-II* Single Sense Electrode 37517 (One Wire Goes To Electrode) Dual Sense Electrode 36998 (Two Wires Go To Electrode, When Substituting For Electrode 37517 Only One Gets Connected)

Why is my Atwood 8531 furnace not igniting?

It turned out to be in the gas valve not getting the proper pressure to the heater. Lifted the little cap off the gas valve and inside turned the inserted screw very gently till it stopped. Do not tighten. The furnace has worked perfectly ever since. I found that my atwood 8531 furnace would not ignite unless I pounded on the side of the furnace.

Why does the Atwood hydro flame furnace not light?

After that, the burner ignites and heat would steadily accumulate in the furnace combustion chamber. The air stream that circulates through the outlets would be warmed by the heat until the set temperature is reached.

Where is the sail switch on an Atwood furnace?

The furnace is rated to be safe and not ignite if the blower doesn’t produce enough air flow (70%). The sail switch is located on the underside of the blower motor (squirrel cage) housing. The switch is held in by two screws.

What to do when a furnace blower fan won’t start?

Tie the red and white wires together, and switch the power on. If the furnace starts, the problem is either with the thermostat wire or thermostat. Replace the wire or thermostat to fix the problem. Your furnace blower fan not starting can have a few causes as you see here.

What does it mean when your furnace won’t turn on?

Easy Troubleshooting in 7 Steps You come home from work, and your house is freezing: the furnace has stopped working. Most of the time when a furnace will not turn on, it is because the thermostat or furnace itself has lost power.

What to do if your Atwood furnace won’t ignite?

Lifted the little cap off the gas valve and inside turned the inserted screw very gently till it stopped. Do not tighten. The furnace has worked perfectly ever since. I found that my atwood 8531 furnace would not ignite unless I pounded on the side of the furnace.

Why does my furnace blower fan not start?

If the furnace starts, the problem is either with the thermostat wire or thermostat. Replace the wire or thermostat to fix the problem. Your furnace blower fan not starting can have a few causes as you see here.

Why does my Atwood furnace keep getting a spark?

It might also be very low propane pressure or if actually 10 seconds, it may not be sensing the heat from the burning propane. In most furnaces, the spark will repeat about 3 to 5 times and then the control goes into lock-out and must be turned off and back on to start over.

Can a Atwood furnace be used in a car?

Atwood furnaces are handy for use in recreational vehicles that operate during cold weather. Atwood furnaces are designed primarily for use in recreational vehicles such as motor homes and travel trailers; they heat the vehicles. Atwood furnaces offer two-stage heating, digital thermostats and self-diagnostics.

What to do if your Atwood furnace is low on heat?

Turn off and unplug the furnace if the heat seems low or inaccurate. Open the main panel on the furnace and take out the filter. Clean the filter with dish-washing liquid and soap, and rinse thoroughly. Set the filter aside to dry, and reinstall it before starting the furnace back up. Contact Atwood with any additional questions or problems.

Why does my furnace blower make a noise?

The most common cause of the noise is from one of the blower motors. Specifically it can be from a faulty or bad start capacitor for the larger blower motor. That problem would result in a noise only at startup. Our noise was constant the entire time the furnace blower was spinning.

Why is my gas furnace making a scary boom noise?

The gas keeps building until—BOOM—it reaches a flame and finally ignites, causing a small explosion in your furnace. Imagine being in a room filled with gas and someone decides to light a match or you turn on the burners to your gas grill and hesitate a moment before pushing the ignite button.

Why does my Atwood flame furnace not light?

Needless to say, no gas would reach the burner if the valve fails to open. Take a look at the valve and assess its quality. In most of the case, you should be able to replace the gas valve at moment notice without much difficulty. 4. Flawed Igniter After you activate the furnace, the igniter would generate sparks and ignite the propane gas.