Why is my Sundance spa not flashing FL1?
If this does not correct the flashing FL1 msg you could have a blockage in the circulation line or at the flow or psi switch or you could have a bad connection at the flow or psi switch or a bad flow or psi switch. If all else fails contact our Service Support Desk to book a diagnostic and repair of your Sundance Spa.
What should I use to clean my Sundance spa?
BEFORE you empty the tub, use a cleaner such as Spa Purge or Aqua Finnesse Spa Clean tablet. Let it run for 20 minutes or longer with all of your jets running and the filter removed–this should go a long way towards dissolving any gunk and build-up in your tubes and filter system. Drain, refill.
Is there an error code on my Sundance Hot Tub?
My Sundance Certa 780 Series hot tub is showing an error of FL1. I went through the manual diagnostics and the error is still there. I contacted Aquatech and they suggested I clean the filter with the FilterBrite. In the first 4 years we basically used one filter and never got this error message.
What kind of error does Sundance certa 780 have?
My Sundance Certa 780 Series hot tub is showing an error of FL1. I went through the manual diagnostics and the error is still there. I contacted Aquatech and they suggested I clean the filter with the FilterBrite.
What should I do when filling my Sundance Hot Tub?
When adding new water to your Sundance hot tub, Put your hose into the filter well so that it runs through the pipes as it fills up, This will help prevent air locks upon re-start. Once your hot tub is filled, You can turn the power back on so it can begin heating up (Do not power up the hot tub until the hose has been removed).
What happens when Sundance spa goes into watchdog?
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.
How can I tell if my Sundance spa filter is defective?
The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation.
What does Flo error on my Sundance spa mean?
A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter. Even if you think it should be fine, give it a try. Sometimes we can’t see the problem with our eyes.
How many people can fit in a Sundance spa?
The top tubs can fit anywhere from 6-7 people while the bottom tubs can fit anywhere from 2-3 people. Each tub comes with Sundance’s ClearRay UV-C Technology and filtration system, perfect for keeping your water fresh and clean throughout the year.
What to do if the main pump is off in Sundance spa?
If debris is present, remove debris, install switch and test system. If condition still exist, replace switch.) if switch measures infinite (no continuity) with pump off, switch is OK, Turn on Main pump and measure across switch terminals for continuity. If continuity is measured, switch is OK.
When did Sundance Spas start making hot tubs?
Sundance® Spas has been manufacturing hot tubs since 1979. They are based out of California, and their products are sold in more than 60 countries. Sundance® Spas focuses on creating acrylic spas, and they are rated as the top worldwide distributor and manufacturer of this particular style. They also produce in-ground and portable hot tub models.
How does the Chelsee hot tub at Sundance work?
A variety of specialized seats throughout the Sundance ® Chelsee are designed to make pain, stress and tension simply fade away. The deep-tissue pressure in the Accu-Pressure ™ is designed to banish fatigued muscles , stress and tension.
How do I change the temperature on my Sundance spa?
1. Ensure your spa is in ‘Standard’ Mode. 2. Then, press the (CYCLE) button three times; The screen will display “U.” At this time the system is ready to accept your changes. 3. Press the select button and it will read “ON”. 4. Press the up or down temperature button until it reads “OFF”. 5.
Sundance® Spas has been manufacturing hot tubs since 1979. They are based out of California, and their products are sold in more than 60 countries. Sundance® Spas focuses on creating acrylic spas, and they are rated as the top worldwide distributor and manufacturer of this particular style. They also produce in-ground and portable hot tub models.
Can a smarttub be added to a Chelsee hot tub?
Control, monitor and operate your Sundance ® Chelsee hot tub from anywhere in the world with our exclusive SmartTub ™ Cellular Technology, SmartTub ™ is an option that can be added and/or factory installed on any newer Sundance ® hot tub. Say Yes to it all in the 780 Series Chelsee Hot Tub!
