Why is my Sundance spa Flo not working?

If you ave one and the jets work, it’s even more likely that it’s a bad pressure switch. Good luck. If the circ pump is buzzing and hot to the touch most likely it is the culprit. If you can remove the equipment access panels, locate the flow switch to see if it is in the closed position or even moving/fluctuating.

What does Flo code on circa pump mean?

Nine times out of ten, a flo code means the pressure switch isn’t working, and ergo your circa pump wont work right, nor usually the heat. It’s a cheap part and won’t take a repair guy more the 20 minutes to fix.

How to diagnose a Flo message on a hot tub?

Answer: When diagnosing a FLO message it is important to consider that there are 3 different types of FLO messages that your Spa’s logic is capable of displaying (a Solid FLO message, a Flashing FLO message and a Solid FLO2 message). First determine which message you are seeing.

What to do if your hot tub has a GFCI breaker?

If this is the case turn the GFCI breaker off to the spa and remove your filter. Make sure there is nothing in the filter area and turn your GFCI back on again.

What kind of filters do I need for my Vita spa?

Vita Spa Filters- We offer a full line of replacement Vita Spa filters in 20/25/40/50 sq. ft. sizes. Vita Spa Jets- A large selection of Vita Spa replacement jets including the Cyclone, QD+, QD200 and Quad Roto jets. Vita Spa Heaters- A full line of replacement Vita Spa heaters – ranging from 4-5.5 kW in many sizes and a low-flow model.

Why does my Vita spa not turn on?

Overheating condition where a water temperature sensor has detected water temperatures of 110°F (43.3°C). Spa functioning is then disabled until temps fall below 108°F (42.2°C).Could indicate a pump operating at low speed for an extended time, constant filtering due to a programming error or a faulty pump. DO NOT GET INTO THE WATER!

What kind of heater does a Vita Spa use?

Vita Spa Heaters – A full line of replacement Vita Spa heaters – ranging from 4-5.5 kW in many sizes and a low-flow model. The world’s first appliance grade hot tub, with a lifetime steel frame and insulation warranty. Vita Spa hot tubs have a reputation of extremely high quality.

If this is the case turn the GFCI breaker off to the spa and remove your filter. Make sure there is nothing in the filter area and turn your GFCI back on again.

What to do if your spa jets are not working?

If your spa’s jets seem weak or are not working, first double-check to make sure that the valves are open. JetPaks have valves at the bottom that open and close by turning the valve. Adjustable jets on M Series, A Series, R Series, and STIL spas open and close by turning the jet face.

What to do when your hot tub is flashing Flo?

First determine which message you are seeing. If you are seeing a Flashing FLO message, check to see that you still have water movement ie your circulation pump is still turning/waterfall is still running, jet and blower buttons still work. If this is the case turn the GFCI breaker off to the spa and remove your filter.

What to do when your spa light goes off?

Shut the spa power off, remove the filter and make sure all the jets are open. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

What to do if your spa has more than one jet pump?

If your spa is equipped with a second jet pump, repeat the priming process for Pump 2 by pressing the “Jets 2” button once to turn on low speed and then a second time to turn Pump 2 on high. If your spa has a 3rd pump, press the “Jets 3” button to prime the third jet pump.

How can I stop bubbles from coming out of my spa Jets?

If the spa jets are on a separate pump, block it’s exhaust flow to the spa. 3) Plug all but 1 spa jet. 5) Repeat for the other jets, i.e. unplug one jet and use that plug to seal the one you just blew.

What to do if your hot tub jets are not working?

First, Turn Off the Power. While it can be a shock to discover that your beloved hot tub’s jets are not functioning, nothing can prepare you for making accidental contact with the high voltage of a hot tub. Therefore, before you start any type of troubleshooting, be sure to power off your hot tub at the breaker box.

Where does Sundance Spas make their hot tubs?

They are based out of California, and their products are sold in more than 60 countries. Sundance® Spas focuses on creating acrylic spas, and they are rated as the top worldwide distributor and manufacturer of this particular style. They also produce in-ground and portable hot tub models.

What does Flo mean on a hot tub?

There are a couple of common causes for float mistakes in hot tubs; however The number one purpose of a spa showing the error code “FLO” is because of a grimy or wiped out filter system. Filters are usually the primary perpetrator as people don’t take time to clean the cartridges quite often, so the pleats get clogged and restrict the flow.

What does Flo code mean on Sundance heat pump?

I found it easily at the Sundance site online and keep a copy on my computer for reference. Nine times out of ten, a flo code means the pressure switch isn’t working, and ergo your circa pump wont work right, nor usually the heat. It’s a cheap part and won’t take a repair guy more the 20 minutes to fix.

Is the heater disabled on a Sundance spa?

OPEN or SHORTED SENSOR (heater disabled) The main temperature sensor is non-functional. This must be repaired only be a Sundance Spas dealer or qualified service technician. CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional.

What are the functions of a Sundance Hot Tub?

There are a number of unique functions designed into your Sundance hot tub to protect it from damage and/or to aid in troubleshooting. The indicator light located on the front cabinet panel of the spa is an early detection system that will notify you when the spa needs immediate attention.

Where is the white light on a Sundance spa?

The indicator light located on the front cabinet panel of the spa is an early detection system that will notify you when the spa needs immediate attention. A solid white light indicates that all operations are normal.

Why do I get a Flo error on my hot tub?

Another thing that you want to check is your skimmer and the filter area. When you look at the spa, you want to make sure that water is flowing in through the skimmer and that there’s no obstructions there. If you did have a filter in, for example, and you got something caught in the system, that can cause a FLO error.

What are the error codes on my hot tub?

Today, I want to talk about two error codes that we get on the top site display. One is FLO and the other is FLC. These two errors deal with the flow going through the heater and the pressure switch. The first thing that you want to do if you get these error codes, is actually take your breaker and turn it off and then turn it back on.

What does an error code on Sundance spa mean?

Indicates that the flow switch is malfunctioning. The system is disabled in this case and system startup has shorted or has a closed flow switch in this situation. Contact the dealer or a service technician. Indicates that spa needs a new UV bulb. Purchase new UV bulb from dealer and reset countdown timer.

What should I do if I get a Flo error on my spa?

Some of them may require a skilled technician to come out and work on your spa for you. 1. The first thing to do if you have a FLO error is to remove your filter and clean it. A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter.

What happens when Sundance spa goes into watchdog?

When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.

What kind of warranty does Sundance Spas have?

Each Sundance Spas series comes with a warranty that covers the shell, cabinets, plumbing, equipment, controls, components, parts and accessories. The Sundance Spas warranty also protects against water loss caused by defects in the shell for five to 10 years, depending on the model you purchase.

How can I tell if my Sundance spa filter is defective?

The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation.

What to do if the main pump is off in Sundance spa?

If debris is present, remove debris, install switch and test system. If condition still exist, replace switch.) if switch measures infinite (no continuity) with pump off, switch is OK, Turn on Main pump and measure across switch terminals for continuity. If continuity is measured, switch is OK.

Why does my Sundance spa go into Oh error code?

Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code

What kind of flow switch does a Sundance Hot Tub use?

This flow switch fits all 1999-present 2 pump or 3 pump systems and 2001+ 1-Pump Capri Systems. Used on the following Spa Models: Sundance 800/850/880 Series, 1999 – Present Sweetwater and Portifino Series with Circulation Pump Jacuzzi J-300 LCD Series Models, 2002+ (with box end connectors).

What kind of circulation pump does Sundance Spa use?

Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.

What to do if your Sundance spa heater is not turning on?

Heater is deactivated and pump may not turn on. Flow/pressure switch is defective. These steps should only be taken after checking and testing the above steps. With the circ pump and the main pump off, test switch operation with an ohmmeter in the continuity position, test for continuity across switch terminals.

What is the flow switch for Sundance Spas?

SUNDANCE SPAS Flow Switch, with Transparent Tee Fitting, Harwil Q-12DS-C2. If you have a small barb fitting on bottom of Tee, order 6560-860. SUNDANCE SPAS Flow Switch, Transparent Tee w/ Barb, For All 6/99-2015 SUNDANCE SPAS 850/880 Series: MAXXUS, OPTIMA, CAMEO, Majesta, ALTAMAR, MARIN, ASPEN. 2001-2004 1-pump CAPRI.

How to troubleshoot a flashing Flo for a spa?

First verify your spa is receiving the specified incoming voltage into the circuit board as well as out of the circuit board to the transformer. Also, check all fuses for continuity. Next, check the service tag on the side of your circulation pump. This will tell you approximately what voltage your circulation pump should be getting.

What should the circulation pump settings be on a Sundance spa 880?

I have a Sundance Spa 880 Series at my new residence and I am wondering what the recommended setting is for the filter/circuation pump. Currently it is set on “Standard Mode” and continuously runs. In my previous residence I had an Arctic Spa that was set to circulate intermittently.

Why did my Sundance 880 get a FlO2 error?

Have a 2010 Sundance Optima 880 spa (OXO3LCD-100378459-0710) giving me FLO2 error. After dropping the curtain to look for the flow switch (and giving it 2 power cycles) it came back to life. When it wasn’t running, flow switch open—closed once flow resumed.

Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.

What should I use to clean my Sundance spa?

BEFORE you empty the tub, use a cleaner such as Spa Purge or Aqua Finnesse Spa Clean tablet. Let it run for 20 minutes or longer with all of your jets running and the filter removed–this should go a long way towards dissolving any gunk and build-up in your tubes and filter system. Drain, refill.

What does Flo error on my Sundance spa mean?

A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter. Even if you think it should be fine, give it a try. Sometimes we can’t see the problem with our eyes.

Why does my Sundance spa not heat up?

It sits 3. I have noticed that that I have a constant FLO error, and the water will NOT heat unless the jets are running. I also believe that my circulation pump is causing these issues. It buzzes and is warm to the touch, but I can’t feel the water moving at all. I just don’t think it is working properly.

How long does a Sundance Hot Tub last?

Sundance Spas can last up to 20 years if properly maintained. Sundance Spas come with a warranty that covers five years on parts and labor and 10 years on the shell. How long does it take to heat a Sundance spa? A Sundance hot tub can take anywhere from four to eight hours to heat, depending on outside temperature and the location of the spa.

How can I know I can trust Sundance Spas?

Sundance Spas sends trained technicians for installation, and the company can work with you to design your outdoor space. Sundance Spas has a comprehensive line of hot tubs with a variety of jet arrangements. Customers can find accurate quotes from their local Sundance Spas showrooms. How do I know I can trust these reviews about Sundance Spas?

Which is the best model of Sundance spa?

All Sundance Spas models come with a footwell, and most include multiple adjustable jets. Some of the most popular Sundance models include the Optima, Cameo, Chelsee and Altamar. Sundance Optima: The Optima has more massage therapy jets for the neck and shoulders than any other model in the 880 series.

What is the error code on the Sundance Spa hot tub?

Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.

Why does my hot tub have a Flo message?

The message can also be caused by soiled filters, plugged or bad Flow switches or a bad connection from the Flow switch to the PWA. In rare instances a bad PWA could cause a solid FLO message. If the pump checks out try and look at the filter, the circ line, the wiring to the Flow switch and the Flow switch.

When did Sundance Spas start making hot tubs?

Sundance® Spas has been manufacturing hot tubs since 1979. They are based out of California, and their products are sold in more than 60 countries. Sundance® Spas focuses on creating acrylic spas, and they are rated as the top worldwide distributor and manufacturer of this particular style. They also produce in-ground and portable hot tub models.

Can a faulty flow switch keep a hot tub running?

Troubleshooting a flow switch can keep your hot tub or spa running. Flow switches are used in spas and hot tubs to tell the system to turn on and off. A damaged or defective flow switch will keep the spa from receiving electricity.