Why is my Spa 2 speed pump not working?
II have a 2002 Optima spa. Several months ago the button on the top-side control panel for the 2 speed pump (#1) stopped working. There’s a second, smaller control panel on the opposite side of the tub which also will not work. But when the preset filter cycles occur the pump will come on and the icon comes on on the display.
What does a hi limit switch on a spa do?
This is what a hi-limit switch does. It’s a safety switch that measures water temperature, tripping if it senses a higher than normal heat rise. A good way to check if the filter is causing the hi-limit switch to trip, is to run the spa without the filter for a couple of days.
What to do if your hot tub has a bad flow switch?
If there is no water movement in the spa check to see if there is hair or debris wrapped around the Flow Switch paddle. If this is not the case you could have a bad Flow Switch. If all else fails contact our Service support team to book a diagnostic and repair of your spa. Replies Theresa Nielsen January 03, 2015 Reply
How does a Hartford loop hot tub blower work?
A Hartford loop is when the ducting is looped up inside the spa cabinet so that part of it goes above the water line. This acts like a sink drain trap and keeps water out of the motor of the blower.
II have a 2002 Optima spa. Several months ago the button on the top-side control panel for the 2 speed pump (#1) stopped working. There’s a second, smaller control panel on the opposite side of the tub which also will not work. But when the preset filter cycles occur the pump will come on and the icon comes on on the display.
If there is no water movement in the spa check to see if there is hair or debris wrapped around the Flow Switch paddle. If this is not the case you could have a bad Flow Switch. If all else fails contact our Service support team to book a diagnostic and repair of your spa. Replies Theresa Nielsen January 03, 2015 Reply
This is what a hi-limit switch does. It’s a safety switch that measures water temperature, tripping if it senses a higher than normal heat rise. A good way to check if the filter is causing the hi-limit switch to trip, is to run the spa without the filter for a couple of days.
A Hartford loop is when the ducting is looped up inside the spa cabinet so that part of it goes above the water line. This acts like a sink drain trap and keeps water out of the motor of the blower.
How do I limit the power that my spa draws from pumps and blowers?
If the available power (amps) for a spa circuit is limited, the installer must consider how much current (amps) each jet pump and/or blower will use and where required must adjust the 1.LLM (load limit) setting to restrict the number of loads that operate at the one time, to keep the total power draw of the spa within the circuit breaker limits.
Why do you need a hot tub blower in a spa?
This minimizes the temperature differential between the water circulating in the spa and the (often) much cooler air being drawn into the system — increasing user comfort and easing the heating burden on the spa’s primary heater. What is the most critical factor for a spa’s air-support system?
Can a spanet heat pump work on any other spa?
SpaNET heat pumps will NOT operate on any other spa control system. They do not have a separate keypad for adjusting settings; rather they feature a dedicated interface to the SV Series spa controller allowing all temperature settings and mode adjustments to be conveniently controlled via the spa side keypad.
How is a hot tub blower different from an air pump?
A hot tub blower is a unit that uses a fan to create air flow and then channels that air through the jets in a hot tub or spa. It is sometimes referred to as an air pump or a bubbler because it creates bubbling in the water (different from a hot tub jet). The components of a hot tub blower are the fan, motor, housing, and the ducting.
Why does my pool blower not work in Spa mode?
If I switch to spa mode, have the pool pump and the spa pump on then cut on the blower most of the time I do not see it blow the water past the check valve. When this occurs after a few minutes it shuts off due to overheating. 20% of the time it does push the water out and works fine after a few minutes.
Can a hot tub blower be switched off?
The GFCI is a current breaker in your hot tub. It can be switched off or “tripped” if the water is getting into your hot tub blower lines. Your hot tub manufacturer has taken measures to avoid this scenario.
How long does it take for a spa blower to work?
When the blower works air comes out of all 6 jets but not the same amount of air, two in the middle get the most and ones farther around have a little less power. When you turn on the spa jets and then turn on the blower you get a big gust of bubbles lasting from 1-3 seconds and then not much else.
Why is the increase button on my spa not working?
If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance spa. Sundance series 880 spa temperature increase button does not work. All other panel functions work. John if the decrease button works and the increase button does not you could have a bad topside control.
What happens when a spa goes into the watchdog?
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model).
What to do if your Sundance spa heater is not turning on?
Heater is deactivated and pump may not turn on. Flow/pressure switch is defective. These steps should only be taken after checking and testing the above steps. With the circ pump and the main pump off, test switch operation with an ohmmeter in the continuity position, test for continuity across switch terminals.
If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance spa. Sundance series 880 spa temperature increase button does not work. All other panel functions work. John if the decrease button works and the increase button does not you could have a bad topside control.
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model).
Heater is deactivated and pump may not turn on. Flow/pressure switch is defective. These steps should only be taken after checking and testing the above steps. With the circ pump and the main pump off, test switch operation with an ohmmeter in the continuity position, test for continuity across switch terminals.
How many Cal spas swim pros are there?
We offer 6 different models in our Swim Pro™ line. Cal Spas Swim Spas X-Series combines our best models from the Swim Pro™ line and takes it to the next level of visual and ergonomic design with new features such as Elite™ cabinets, Cal Grip™, Cal Touch4 Control™ and Cal Armor™.
How many Cal spas are there in California?
Cal Spas Swim Pro™ Swim & Fitness Spas allow customers to enjoy the convenience of a complete aquatic exercise regime in the comforts of their own backyard. We offer 6 different models in our Swim Pro™ line.
What are the functions of the spa pump?
The Spa is recirc and temperature controlling correctly and the pumps are working during the daily auto cycle with an LCD icon on display. The main control panel looks fine (no misting), is backlit, the light buttons work correctly, but no other button functions are working (Temp, Pumps, Programming).
We offer 6 different models in our Swim Pro™ line. Cal Spas Swim Spas X-Series combines our best models from the Swim Pro™ line and takes it to the next level of visual and ergonomic design with new features such as Elite™ cabinets, Cal Grip™, Cal Touch4 Control™ and Cal Armor™.
Cal Spas Swim Pro™ Swim & Fitness Spas allow customers to enjoy the convenience of a complete aquatic exercise regime in the comforts of their own backyard. We offer 6 different models in our Swim Pro™ line.
Where is the Cal Spa in Pomona CA?
Cal Spas current headquarters grew into a 1-million square foot State-of-the-Art manufacturing plant in Pomona, California. When you bask in the warm waters of your new hot tub or swim spa, you are free to let your imagination wonder while the stresses of the day disappear.
