Why is my Lippert ground control leveling not working?

I dont know if the leveling system is a 2.0 or 3.0. The display on the touch pad is blank. The back light comes on, but no words, It seems like everything else works, I can press the auto level button and it works. I can press the retract button and retract the landing jacks, I just cant see anything on the display.

What to do if your HWH leveling system is not working?

If you have lost it then search the official website of HWH to find a copy of the manual. Make sure that you enter the exact model of the system you have installed on your vehicle. The most common process to reset these jacks is by completely retracting the entire system.

What happens when you press the button on a leveling jack?

Nothing can create that sinking feeling in your stomach quite like pressing the button to operate your leveling jacks and having nothing happen. That can make for a bad start to a trip or it can provide a terrible ending to an otherwise fun getaway. Whether your jacks are stuck up or down can make a big difference in the criticality of the fix.

What kind of leveling system does a Winnebago Brave have?

Have a 2004 Winnebago Brave with the HWH 325 series Leveling System. While driving the yellow ‘Jacks Down’ indicator light turned on and buzzer sounded, pulled over and found the LR jack was down about 1/4 inch with the round RF jack indicator on the keypad was ‘red’.

How to troubleshoot Lippert electronic RV leveling system?

An error occurred. Please try again later. (Playback ID: 6fiPyKf9fiinnJET) An error occurred while retrieving sharing information. Please try again later.

How does Ground Control 3.0 Power leveling system work?

Available in both 4-point and 6-point configurations, the Ground Control 3.0 power leveling system uses Hall Effect technology to efficiently and accurately level your RV by measuring the motor revolutions of your jack’s legs, instead of amps.

Is the Lippert electronic leveling system serviceable?

The Lippert Electronic Leveling System is totally integrated into the chassis of the coach at the manufacturer. There are no serviceable parts within the electric motor. If the motor fails, Pump Unit must be replaced. Disassembly of the Pump Assembly voids the warranty. Mechanical portions of the Lippert Electronic Leveling System are replaceable.

What to do if your Lippert LCD is not working?

Before replacing the third one, I recommend unplugging the connections on the panel and cleaning them prior to reconnecting. If this doesn’t solve your problem, then I recommend the Replacement Auto Level Control Panel for Lippert Ground Control Leveling System # LC421484 to give you the working LCD display.

What do you need to know about Lippert components?

Lippert Components has developed a range of leveling and stabilization solutions to enhance every RV set up. We’ve made it faster, easier and simpler to get your RV up and running at the campsite and to maintain a stable and safe foundation for the RV lifestyle.

What kind of fluid do you use for leveling jacks?

Hello Joe, Typically Fleetwood used the Power Gear leveling system which is now owned by Lippert Components Inc (LCI). According to the Power Gear manual, they recommend the following: Type A automatic transmission fluid (ATF, Dexron III, etc.,)will work satisfactorily.

Why do I need leveling jacks on my Lippert slide out?

RV leveling jacks are essential for a sturdy and safe stay in your Lippert slide room. If the leveling jacks on your slide-out give you trouble when you set up camp for the night, there are a couple things you should inspect when troubleshooting to find the issue and come up with a solution.

What should I do if my leveling jacks are not working?

Silicones and cleaning agents such as Dawn dish soap can worsen the corrosion and render your system irreparable. So what you should do is spray the system well with WD-40 and then wipe clean.

Why is there no power on my LCI?

If nothing is getting power I’m wondering if your trailer itself is getting power. If your batteries are depleted and you don’t have your trailer electrical connected to your tow vehicle then there isn’t any power getting to your trailer and is makes sense that nothing is working.

How do I Reset my Lippert auto leveling system?

Once you are satisfied with your leveling (I leveled my coach 1 degree high in the front so A/C condensation would drain at the rear of the coach) you turn off your leveling system and press front 5 times and then press rear 5 times your system should come on and indicate that calibration has been reset.

What’s the best way to level a Lippert?

Put the controller in manual mode and get the unit level that way first. As close to perfect as you can with a carpenters level in the center of the rig. Level front to back and side to side. Triple check it as when your done this is your new zero point.

Why is my Lippert 6 point leveling system reset?

The screen being blank sounds like a power issue and beeping indicates you need to reset/recalibrate the system due to that lack of power. The beeping is telling you the zero point needs to be reset. 1. Turn “ON/OFF” button “OFF”. 2. Push “FRONT” button 10 times.

How to reset zero point on Lippert ground?

Use the up key pad to cycle thru until you teach manual mode and press enter. From here you can extend or lower as needed Once you have it level, then follow the steps Erik posted to set you zero point. Note: on some Lippert systems, you have to press the Front and Rear buttons 10 times versus 5.

Why is my LCI leveling system not working?

My lci electronic leveling system for winnabago has Jacks down and is indicating low voltage but I know that the batteries are fully charged and prior to shut down indicated 13.6v. This sounds like it is a ground issue. If your ground wire from the control module is grounded to the frame, I would try removing the ground and cleaning the surface.

What to do if your Lippert display is not working?

If this doesn’t solve your problem, then I recommend the Replacement Auto Level Control Panel for Lippert Ground Control Leveling System # LC421484 to give you the working LCD display.

How to set zero point on Lippert ground?

To set the current position as the zero point, press the “ENTER” button. 6. LCD display will read “Zero point stability check”. 7. LCD display will read “Zero point set successfully” once process is complete. 8. The system will set this point as its level state and the touch pad will turn off.

If this doesn’t solve your problem, then I recommend the Replacement Auto Level Control Panel for Lippert Ground Control Leveling System # LC421484 to give you the working LCD display.

How can I Reset my Lippert LCI leveling system?

My Lippert LCI leveling system is showing jacks down when the jacks are up. All the lights start blinking with break off and ignition on. Cannot lower jacks. Reset by pushing all four buttons just stops it for a second then lights start blinking again. Checked fuses. After a few minutes just the lights on left side blink.

How does an automatic leveling system work on a RV?

The patented six-point Level Up® hydraulic leveling system levels an RV in less than a minute using a one-touch auto-leveling feature, and includes an auto re-hitch memory function that remembers the exact height at which the RV was unhitched.

Why are there no log messages in the terminal?

By default the console always gets log messages, so nothing shows in the logging output above. By default the terminal doesnít show log messages and so nothing shows int the logging output above. If you want logging messages from IOS to appear on the your terminal then you need to use the ‘ terminal monitor ‘ command.

What do the warning messages on my Ford Taurus mean?

Warning message displays when the system requires service due to a malfunction. Arrange to have the alarm serviced by your Ford dealer. This information message displays when the engine has shut off to help increase fuel economy. This information message displays when the engine is getting ready to shut off.

What happens when you put a performance message on your car?

The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer/retailer for service as soon as possible.

When does the AWD warning message turn off?

If your vehicle has the All-Wheel Drive (AWD) system, this message displays when the rear drive system is overheating. This message turns off when the rear drive system cools down. If the warning message stays on for a while, you need to reset the warning message. To reset the warning message, turn the ignition off and then back on again.

When does all wheel drive off message go off?

ALL WHEEL DRIVE OFF If your vehicle has the All-Wheel Drive (AWD) system, this message displays when the rear drive system is overheating. This message turns off when the rear drive system cools down. If the warning message stays on for a while, you need to reset the warning message.