Why is my Intermatic timer not keeping time?
Poor wiring in the load can hinder the timer from keeping time when the load turns on using the manual lever. Additionally, a loose wire can cause failure of the load to turn on or off when the dial rotates on time. A tripped circuit breaker or a defective supply cable can cause power supply deficiency in the timer.
Can a time clock be replaced on an Intermatic pool pump?
Intermatic time clock motors can be replaced, but unless the time clock was fairly new, I’d probably just replace the entire Intermatic mechanism. But then again, Intermatic timer motors can be half the cost of a new mechanism, depending on the model. Here’s a real nice pictorial on how to replace an Intermatic timer motor, or mechanism.
How long does it take to replace an Intermatic time clock?
It can actually take less than 5 minutes. Intermatic time clock motors can be replaced, but unless the time clock was fairly new, I’d probably just replace the entire Intermatic mechanism. But then again, Intermatic timer motors can be half the cost of a new mechanism, depending on the model.
Why does my Intermatic pool not turn off?
The trippers push on a tab on the on/off switch. So either the tripper is broken (or installed out of alignment) or the tab (s) on the on/off switch are broken. You can turn the dial and then only wait a few minutes to check is the OFF tab is working.
Is the Intermatic timer working but does not turn time?
Intermatic Timer Motor is working but does not turn time dial. I have an issue with a T104 Intermatic Timer that the dial will not keep time, thus it will never turn on or off the pool pump. The motor is working I can see it turning through the peep hole. The pump turns on and off manually just fine..
Intermatic time clock motors can be replaced, but unless the time clock was fairly new, I’d probably just replace the entire Intermatic mechanism. But then again, Intermatic timer motors can be half the cost of a new mechanism, depending on the model. Here’s a real nice pictorial on how to replace an Intermatic timer motor, or mechanism.
The trippers push on a tab on the on/off switch. So either the tripper is broken (or installed out of alignment) or the tab (s) on the on/off switch are broken. You can turn the dial and then only wait a few minutes to check is the OFF tab is working.
Is the Intermatic et1125c an electronic time switch?
This series offers an easy way to upgrade from a basic mechanical time switch to an electronic time switch. These timers will allow for up-to-the-minute programming, battery backup for power loss, up to 28 events total, and automatic daylight saving time corrections without the need of user interaction. . . . .
How to adjust the Intermatic pool timer wheel?
How To Adjust The Timer Wheel On Intermatic Pool Timers. To adjust the time you will first want to look for the “time” bar that is mounted in the middle of the timer wheel. Then number (time of day) that you line up with the time marker will be the time that you are setting your timer to. So if you see the 10am behind the “time” marker,…
Why does my Intermatic pool pump not turn on?
If power is reaching the clock, and the gears are turning, but the dial is not turning – this could mean that the gear on the back of the dial has not engaged. Grasp the dial, pull out and turn it to the correct time.
Why is my Intermatic not turning on or off?
Following Irma and 2 days without power my intermatic timer was set wrong. I’ve reset it per the directions and it’s counting time properly, but when it should turn on (10AM, and off 2PM) it doesn’t change (just stays in the previous condition). I have to turn it on/off myself.
What causes problems with an Intermatic time clock?
Problems with Intermatic timers are caused by defective trippers, incorrect wiring, tripped circuit breakers, a faulty time clock motor and incorrectly set power terminals. Other causes include rusted springs, insect infestation and loose timer dogs.
How do you set a timer on Intermatic?
This is a mechanical timer and to set the time you must pull on dial and rotate it to the correct time (watch AM vs. PM). The dial must return to the seated position for it to hit (activate) the trippers. The trippers must be perpendicular to the outside edge of the dial and make sure the set screws are tight.
