Why is my Hayward Super pump not priming?
I have a hayward super pump II. It is not priming on its own. To get it to prime I must shut all 3 intake valves from my skimmers and the main drain, put water in the basket, turn on the pump and then 1/2 way open the closest skimmer. I must do this 3 times to get the thing to prime.
Can a Hayward pump and de filter have no pressure?
Hayward Pump And DE Filter With No Pressure WeT HeaD July 18, 2009 Pools 22 Comments Question: I have the same problem with no pressure. Have an above ground pool with a Hayward pump and DE filter. We took the filter apart and cleaned it, the pressure was great for a few days, now nothing again.
How can I get water out of my Hayward pump?
3) Go to the pump and open the lid a bit, and then there will a big rush of water that comes out from the pump. What this will do is remove the hydro-lock that often happens in above ground pools. Once the water rushed out of the pump for a few seconds , close the lid.
Why is the return line on the Hayward pump leaking?
A common mistake is that some people think the return line is leaking because they see the air coming from the returns lines but in fact the air is being drawn into the pump from the suction side.There are a few places on the Hayward Super Pump that you will want to make sure are sealed well.
Why does my Hayward pump have no pressure?
THE PUMP: Make sure you pump impeller is not clogged and the eye is free of debris. Sometimes the impellers on the pump get clogged and then the pump will not ave enough pressure to pump through the filter. I would check the above and let me know if you need more help or ask more questions.
How can I Stop my Hayward Super pump from leaking?
If your Hayward Super pump is still connect to the filter system you will need to remove it by loosing the unions that should be on the suction side and the discharge side of the pump. You can loosen these unions with a large pair of channel lock pliers.
Why does my Hayward pool pump blow bubbles?
If you have a Hayward Super Pump powering your above ground or in ground pool then you will know from time to time you may develop some air leaks inside of the pump. This air that gets sucked in from the pump fittings will travel through the swimming pool plumbing and then wind up blowing bubbles from the return jets of your pool.
Why is my Hayward pool VAC not moving?
If there’s not enough suction, it won’t move much. Question: My Hayward pool vac wasn’t moving so I replaced the A-frame and turbine kit. It now only stays in one section of the pool. No matter where I move it, it always makes it way back to the same section and does circles in that area.
How long does it take to Prime a Hayward pool pump?
How To Prime The Hayward Super Pump. The Hayward Super Pump should prime in anywhere from 30 seconds to 3 minutes depending on how far your filter system is from the pump. The further the pool or spa is from the intake (skimmers or main drain) the longer it will take for the pump to prime.
What to do if your Hayward pool pump won’t turn on?
It’s a Hayward 3/4 HP Super Pump. With the power removed from the pump and the water valves off take out your leaf basket and see if you can reach into the impeller area and see if the impeller (pump vanes) is free/moving?
What do you need to know about priming a pump?
Make sure the pump is turned off before priming. Close all valves on the suction side of the pump, including the main drain, skimmer and vacuum lines. Some pumps have an air release valve, if you do, open it. If your pump does not have an air release valve, be sure to remove the strainer lid slowly to let the pressure slowly escape.
Why pump will not prime?
Most of the time when a pump will not prime (fill up with water) it is because there is an air leak on what is called the suction side of your plumbing. You need to double check that the lid on the pump basket has a good O-ring and that you have installed the lid securely.
Why pool pump won’t Prime?
There are several reasons why pool pumps tend to lose their prime or are unable to reprime themselves, the most common problem results from air in the pipes or filter. This is usually caused by the pools water level being too low or sometimes is caused by loose fittings or perished o’rings.
Why does a pool pump lose prime?
Small air leaks reduce the efficiency of a swimming pool pump and cause an irritating gurgle in a swimming pool, usually at the return jet closest to the equipment. Large amounts of air can bring the system to a complete halt by causing it to lose prime.
Do you have to lubricate Hayward pool pump?
Hunker may earn compensation through affiliate links in this story. Clean strainer basket regularly. Hayward Pumps have self-lubricating motor bearings and shaft seals. No lubrication is necessary Pump and motor must be protected from freezing.
What does it mean when your pool pump wont Prime?
If there is air in the pool pump chamber or intake line, your pump can’t prime or create enough suction to properly pull water through the filter and back out to the pool. Several issues can contribute to this problem, but there are some basic steps you can take to try to resolve the issue: Turn the power off.
Do you need lubrication for Hayward swimming pool?
Hayward Pumps have self-lubricating motor bearings and shaft seals. No lubrication is necessary Pump and motor must be protected from freezing. Swimming pools require a lot of maintenance to ensure proper chemical balance and efficient cleaning systems.
What happens when you Prim A Hayward pool pump?
Priming your pump will remove any air in the pump, causing the water to move through the filter. Priming can avoid the cost of a service call and provides other benefits. The steps are the same whatever model Hayward pool pump you own. Make sure the pump is turned off before priming.
Do you still need Hayward pumps and filters?
We carry the other brands, but Hayward pumps and filters have always been our flagship line. Reliable & durable, Hayward pumps will still likely need some type of troubleshooting at some point during your relationship.
What should I do if my pool pump won’t Prime?
Open the filter air relief valve while the pump is trying to prime. If you have a SPA you can adjust the water flow to suck from the SPA drain. (Make sure to change the valve back to the correct position once you are finished either attempting or priming the pump.
What happens if a pool motor is not priming?
This guide discusses the common problems involved with a motor that is not priming. Most priming problems involve leaks in the suction side of the pump (between the pump and the pool) or clogged baskets. If you have a leak on the pressure side (after the pump), it does not affect prime. You just lose water.
