Why is my gecko spa pack not working?

Sometimes the spa pack controls will display error codes or flashing lights. When this happens, the owner needs to do a bit of troubleshooting to fix the problem. Loosen the two screws that hold the cover onto the control pack. Lift the cover off to reveal the LED board.

Which is the best gecko hot tub system?

Our new in.yj is perfect system for any small footprint spa. in.xm and in.xe platforms from our X series include all the features and functions the spa and hot tub industry expects in stunning power box designs that break all rules and standards with their superb combination of looks and functionality.

How does the hot tub control panel work?

The hot tub control panel is like a timer that keeps the spa’s temperature constant. It turns off the spa when you forget to and troubleshoots problems. Thus, it is very important to have a spa control system in good working condition. Many issues could face your spa, including electrical issues.

What should water temp be in gecko spa?

The temperature inside the spa skirt is high when the display reads SP-OT. The overall water temperature is over 112 degrees when SP-OH is on the display. Always take care when working with electrical devices near water to avoid injury from electrical shock.

What does SP-BR mean on gecko spa pack?

SP-BR means that the circuit breaker setting is too low and the spa is not getting enough power to run properly. SP-IN means that the input voltage is low. Check the circuit breaker and wiring to see if any fuses have blown. Reset fuse 1 or fuse 2 on the circuit breaker when SP-F1, F1 or F3 appear on the display.

How does smart winter mode work on a gecko?

When Warm Weather is “OFF” the filtration over-temperature is disabled and your spa filtering will continue even if the water temperature is high. “Display” and “Hide” buttons allows you to modify message display. If “Hide” option is selected, Smart Winter Mode message will only appear when a SWM purge is in action.

How do you turn on Spa on gecko?

Touch the screen to turn on the keypad and drag the icon into the circle to unlock the keypad. in.k1000+ features an all-on or all-off one touch activation key which stops or starts all working components and accessories at once. To select a spa mode, slide the left wheel up or down until the spa icon is highlighted in the middle.

What are the parts for a gecko hot tub?

AquaFlo Pump Seal part number 92500150 for Gecko Aqua-Flo XP2, XP2E, XP3, FloMaster, and CircMaster spa pumps. The pump seal kit measurements: Original Seal kit – 2 parts for XP2 XP2E and… Light socket cable adapter 9920-400489. This is a light socket with 8′ cable to MTA-156 for Gecko IN.YE Series.

What does the gecko spa pack keypad do?

The keypads of the Gecko Spa Pack are simple interfaces used to control the day-to-day operations of a spa. Sometimes the spa pack controls will display error codes or flashing lights. When this happens, the owner needs to do a bit of troubleshooting to fix the problem.

How do I Turn Off the pump on my spa?

Depending on the spa configuration, in.k1000+ can control up to 5 pumps, a blower and lights. Three minutes after the last pump has been turned off, the screen will shut off. Touch the screen to turn on the keypad and drag the icon into the circle to unlock the keypad.

When to replace a gecko hot tub circuit board?

Gecko Circuit Board: If you have three flashing dots on the display and there is a red light illuminated on the circuit board then the high limit sensor needs to be replaced. If the red light is not on, then there is a flow issue or faulty pressure switch. See “error codes/blinking dots” above. 3.

Why are there flashing lights on my spa pack?

How do you replace a gecko hot tub controller?

If your old hot tub controller had a 15″ long heater tube then the new Gecko spa pack will just drop right in and the plumbing unions should thread right onto the new heater. For the rest there are step by step instructions included with every Gecko spa pack from the factory.

What to do if your spa control panel is frozen?

If the control panel is frozen or dead, you have to check if the problem is the control panel or the circuit board. Examine if there is moisture in the display. Check if there are cracked buttons or if a part is wet. If only a part is not working, look for error messages or blinking lights. As a first step, reset your breaker.

What do you need to know about gecko spa pack control?

Always take care when working with electrical devices near water to avoid injury from electrical shock. Gecko spa pack controls are control panels found on spas. The keypads of the Gecko Spa Pack are simple interfaces used to control the day-to-day operations of a spa. Sometimes the spa pack controls will display error codes or flashing lights.

Why is my spa control panel not working?

Reset the control panel if it only displays dashes and not error messages. Turn the power off for one hour and then turn it back on. If the control panel is displaying strange messages or have lights blinking at the same time, it could be a software issue with the circuit board.

How to troubleshoot a gecko Y series controller?

All outputs including heater are deactivated until the next flow check 2 hours later. Reboot the controller and wait the FLO status update. If the FLO LED is OFF, go to case #10. Then if the controller succeeds in flow checking, the Kinetic error will disappear. If the FLO LED is ON, proceed to the normal maintenance, filters cleaning…

What can cause damage to a gecko control system?

* LOW SUPPLY VOLTAGE OR IMPROPER WIRING MAY CAUSE DAMAGE TO THIS CONTROL SYSTEM. READ AND FOLLOW ALL WIRING INSTRUCTIONS WHEN CONNECTING TO POWER SUPPLY. * THIS PACK CONTAINS NO USER SERVICEABLE PARTS.

What do you need to know about gecko depot?

Spa packs, controls, accessories, parts and more. Gecko Depot. Advanced electronic controls and accessories for the spa and hot tub industry presented Gecko Depot: Online Store for Spa Packs, Controls, Pumps, Parts and Accessories for Spas Welcome to Gecko Depot Spa packs, controls, pumps, accessories, parts and more

What is the code for a gecko hot tub?

Gecko Error Codes also cover any control box manufactured by Gecko and Spa Builders. Click on any Blue error code below for a description of causes, troubleshooting and repair information. CoLd : Temp in heater housing is below 40° F. Low speed / circ pump will operate continuously until the temp rises above 45° F. OH : Overheat.

Where can I find the gecko error code?

Gecko Error Codes also cover any control box manufactured by Gecko and Spa Builders. Click on any Blue error code below for a description of causes, troubleshooting and repair information.

Do You need A MspA filter for a hot tub?

The spa pool liner and cover must be extended evenly around when the spa is filled with water. A MSpa must be placed on a completely flat and solid surface. Otherwise it can cause the spa to be lopsided. Why can I see algae in the spa even if I’ve used the filter regularly?

How to do the TSPA-MP metapacks service manual?

4 TSPA-MP Metapacks Service Manual Electrical Wiring Correct wiring of the electrical service box, GFCI box and pack terminal block is essential. 1• Carry out a visual inspection to check for signs of miswiring. Refer to supplied wiring diagrams. Call an electrician if necessary.

Why is my coast spa power supply not working?

If all connections are made, but nothing seems to be working, you probably have a power supply problem. Carry out the following tests to identify and correct the problem: Note that for new installations, GFCI trippings due to miswiring are common.

What is the coast spas TSPA-MP service manual?

COAST SPAS TSPA-MP SERVICE MANUAL • Gecko Electronics Inc. • Visual step-by-step guide to easily identify & correct technical problems! Table of Contents Power & Ground Check Electrical Wiring 4 GFCI 5 Error Conditions

What causes no flow on gecko y controller?

If ON, possible causes: KINETIC state: No flow detected for more than 2 hours Wait 2 hours and validate the status of the LED KIN another time to confirm that KINETIC error is permanent All outputs including heater are deactivated until the next flow check 2 hours later. Reboot the controller and wait the FLO status update.

Where can I find a troubleshooting guide for gecko?

Possible error codes Error code explanation Step by step troubleshooting 9919-101313-C Rev. 01-2021 ÂŠ Groupe Gecko Alliance inc., 2021 All trademarks or registered trademarks are the property of their respective owners. Gecko Alliance 450 des Canetons, Quebec City (Qc), G2E 5W6 Canada, 1.800.78.GECKO

Where can I buy gecko hot tub controls?

Large selection of Gecko hot tub keypads and topside controls for Gecko, Y Series, S Class, IN.XM and IN.XE spa control packs for hot tubs in Canada.All Gecko topside controls and keypads are ready to ship from locations across Canada from our large inventory.

What do you need to replace a gecko circuit board?

To properly identify the correct replacement for a Gecko circuit board, you will need the “Model” and “Options” numbers. The Model and Options numbers are a series of alphanumeric numbers located on a label on the outside of your spa pack.

What are the parts for a gecko pump?

For transformer / S-CLASS packs For pumps / S-CLASS and M-CLASS packs Compatible with: Y series & M-Class systems For transformer (F4) / in.xe, Y series packs Includes: brackets, screws. Wood screws not included Compatible with: Y series & M-Class systems

How many pumps can a gecko spa pack control?

The Gecko Spa Pack bundles range from the small JY system for a small 1 pump hot tub all the way up to the YT series which can control up to 5 pumps and more accessories. The benefit of updating your hot tubs control system with a current generation Gecko spa pack is that the Gecko controllers have many ad on options available.

What are the keypads for the gecko spa?

With their bright, full color display, Gecko’s in.k800 and in.k500 keypads provide the ultimate user experience with their screen’s high resolution that brings spa user interfaces to a new level. 10 keys, large color display, menu-driven interface for Gecko’s X and Y series of control systems for spas.

Which is the best gecko hot tub control system?

Selecting a correct bundle from Gecko is the most economical way to update your hot tubs control system with the current generation digital system. The Gecko Spa Pack bundles range from the small JY system for a small 1 pump hot tub all the way up to the YT series which can control up to 5 pumps and more accessories.

What are the keypads on a gecko depot hot tub?

Works with keypads in.k200, in.k19, in.k35, in.k450, in.k600 static, in.k120 (auxiliary) and in.touch Wi-Fi module. Most rugged spa pack platform ever developed for spa and hot tub manufacturers.

What are the error codes on a gecko heater?

Gecko Error Codes also cover any control box manufactured by Gecko. Overheat. Spa has shut down. One sensor has detected 118º F at heater. Overheat. Spa has shut down. One sensor has detected 110º F. Spa is shut down. Sensor plugged into jack A is not working. Spa is shut down.

Are there any gecko keypads for hot tubs?

Take them in your hands, get their feel, press a key or two, look at their display and you’ll know you’re holding Gecko’s promises of advanced and reliable technology, a complete series of multi-function and multi-feature keypads for spas and hot tubs. Introducing our new full featured in.k1000+ keypad with color capacitive touch screen display.

What do you need to know about the gecko pump?

Complete series of keypads for spas and hot tubs. Certified pump lineups for small to swim spas. Added value to increase the quality of the spa experience. Total flexibility, total compatibility, total satisfaction with Gecko’s X, Y and Class series of control systems for spas and hot tubs.

How many buttons does a gecko keypad have?

Gecko IN.K8-3OP with Overlay 0607-007067 is an 8 button Gecko control panel that includes the overlay 9916-101675. in.k8-3OP keypad with overlay has 8 buttons: Pump 1/Pump 2/Pump 3 or Blower/Light/…

What should I do if my gecko heater is not working?

An error occurred. Please try again later. (Playback ID: RgVbFrWBOZ4smsa_) Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.

How to troubleshoot an in.xe by Gecko?

* TURN POWER OFF BEFORE SERVICING OR MODIFYING ANY CABLE CONNECTIONS IN THIS UNIT. * TO PREVENT ELECTRIC SHOCK HAZARD AND/OR WATER DAMAGE TO THIS CONTROL, ALL UNUSED BUSHING CONDUITS MUST BE PLUGGED WITH THE ATTACHED NIPPLE. * THIS CONTROLLER MUST NOT BE INSTALLED IN PROXIMITY OF HIGHLY FLAMMABLE MATERIALS.

What to do if your gecko Spa is not working?

Verify that the temperature probe is submerged in the water and properly connected. Place a one-inch thick piece of foam around it if it does not reach the waterline of the spa to prevent cold air from reaching it. You may need to replace the pack if the display continues to show the wrong water temperature.

What does 230 volts mean on gecko spa pack control?

A reading of 230 volts means it is getting enough power. Check to see if all the wires are connected to the keypad. Remove the transformer, which is a small silver rectangle with blue, yellow, white, black and red wires coming out that leads to a plastic orange connector.