Why is my Atwood levelegs Control Board not set?
1. The control board must be mounted horizontally, on a solid fixed surface and can not be more than 10 degrees out of level. 2. Manually set coach to desired position and program position into memory, following the steps in the IOM. PANEL LIGHTS BLINK “ON” AND “OFF” Cause: An Auto Position is not set. Solution:
How to check voltage on an Atwood RV?
Check voltage with a digital voltmeter at the control panel while deploying the jacks. If 12+VDC, I would suggest giving Atwood a call at 800-546-8759. I have the Atwood Levelegs. To prevent the low voltage problem the engine must be running at a little more than idle.
Where can I get an Atwood Awood controller?
Atwood Tech Service is GREAT! Do not hesitate to call if you have an Atwood problem. Other RV product mfgs. should emulate them. I need an Awood controller 66235 as mine will no longer work. Can anyone help me either repair this one or get one from a salvage yard?
How big are the power jacks on Atwood levelegs?
The size is about #22 gauge. These are signal wires only with mini Walden-Molex connectors. The power wires are not a problem. They are about #8 gauge. The connectors to that feed the individual jacks have # 10 or #12 wire and have never been a problem.
1. The control board must be mounted horizontally, on a solid fixed surface and can not be more than 10 degrees out of level. 2. Manually set coach to desired position and program position into memory, following the steps in the IOM. PANEL LIGHTS BLINK “ON” AND “OFF” Cause: An Auto Position is not set. Solution:
Atwood Tech Service is GREAT! Do not hesitate to call if you have an Atwood problem. Other RV product mfgs. should emulate them. I need an Awood controller 66235 as mine will no longer work. Can anyone help me either repair this one or get one from a salvage yard?
What to do if your Atwood engine is low voltage?
If 12+VDC, I would suggest giving Atwood a call at 800-546-8759. I have the Atwood Levelegs. To prevent the low voltage problem the engine must be running at a little more than idle. If you try to run the jacks without the engine running, the low voltage indicator will stop the process. That makes sense.
The size is about #22 gauge. These are signal wires only with mini Walden-Molex connectors. The power wires are not a problem. They are about #8 gauge. The connectors to that feed the individual jacks have # 10 or #12 wire and have never been a problem.
Where is the red light on Atwood levelegs?
Next, try turning off the key and manually spinning the retractor nut a few turns (they’re on the end of the motors near the top of each leg and should turn fairly easily) for the leg with the blinking red light. If you take a paper towel or rag with you, you can keep your hand from getting grimy.
When do Atwood levelegs Jacks get cranky?
It seems the jacks only get cranky when they haven’t been used in a while and they are fully extended. If you make blocks like these, I’d recommend using treated lumber, then priming and painting them, otherwise they’ll rot quickly when in contact with the ground.
How does the leveler system always return to position in memory?
Solution: Leveler System always returns to position in memory. 1. The control board must be mounted horizontally, on a solid fixed surface and can not be more than 10 degrees out of level. 2. Manually set coach to desired position and program position into memory, following the steps in the IOM. PANEL LIGHTS BLINK “ON” AND “OFF” Cause:
What to do if your Atwood levelegs won’t move?
If your Atwood Levelegs electric jacks quietly refuse to move, make sure that the engine is running, the rig is in park, and you have the parking/emergency brake set.
It seems the jacks only get cranky when they haven’t been used in a while and they are fully extended. If you make blocks like these, I’d recommend using treated lumber, then priming and painting them, otherwise they’ll rot quickly when in contact with the ground.
Next, try turning off the key and manually spinning the retractor nut a few turns (they’re on the end of the motors near the top of each leg and should turn fairly easily) for the leg with the blinking red light. If you take a paper towel or rag with you, you can keep your hand from getting grimy.
Check voltage with a digital voltmeter at the control panel while deploying the jacks. If 12+VDC, I would suggest giving Atwood a call at 800-546-8759. I have the Atwood Levelegs. To prevent the low voltage problem the engine must be running at a little more than idle.
What to do when your levelegs system goes into error mode?
Solution: Put system in error mode by disconnecting one jack from power and pressing RET and ALL. Reconnect jack to power. Manually extend individual jacks for 10 seconds by holding down the EXT key and the two jack keys that make up the camper corner of that jack. Listen to insure all jacks move when manually activated.
What to do if your leveler is not level?
1. Insure vehicle engine is running, transmission is in park and park brake is set. 2. If emergency stop was activated by pressing any keypad button, press ‘RET’ and ‘ALL’ to reset legs. 3 AUTO POSITION DOES NOT LEVEL THE COACH Cause: The last position in memory was not level. Solution: Leveler System always returns to position in memory. 1.
What happens if no current is detected after leveler is activated?
During any operation if no current is detected from leveler after leveler is activated, the following occurs: 1. Warning alarm will sound. 2. Power is removed from the control box disabling normal operations. 3. The red and green LED’s for that leveler will blink on and off to indicate the system is in an error mode. Solution: To proceed, 1.
What causes short Jack extension on Atwood camper?
Cause: Short jack extension followed by jack retraction. Solution: Put system in error mode by disconnecting one jack from power and pressing RET and ALL. Reconnect jack to power. Manually extend individual jacks for 10 seconds by holding down the EXT key and the two jack keys that make up the camper corner of that jack.
Why are the leveling jacks on my RV not working?
Check the solenoid valve for any leaks. The cylinder itself could have a an internal leak, would have to check the seals. The manifold has a check valve that could have failed. Debris could have also entered the system either when the solenoid was installed or prior. You would then have to clean and flush the system.
During any operation if no current is detected from leveler after leveler is activated, the following occurs: 1. Warning alarm will sound. 2. Power is removed from the control box disabling normal operations. 3. The red and green LED’s for that leveler will blink on and off to indicate the system is in an error mode. Solution: To proceed, 1.
What are the flashing lights on my Atwood levelegs?
Periodically, especially if the rig has been sitting for a while, my Atwood Levelegs electric jacks will refuse to retract and will display flashing green and red lights, usually in one corner, indicating which jack is having trouble.
Why does my Atwood leveler not shut off?
The drivers front would not extend and the balance of the levelers also stopped. Got everything retracted but alarm on leveler will not shut off when engine is on. Called dealer and he told me how to disconnect panel. Any thoughts on the problem would be greatly appreciated.
What kind of leveling system does my Fleetwood Southwind have?
My coach is a 2006 Fleetwood Southwind. The Atwood system is electric. The face of the system states, “Atwood P/N 66273”. Opps typo, my coach is 2005. Location:Where ever the wheels stop ? Deborah, This is some information on an Atwood Electric leveling system. Might be close to your system.
How to retract jacks on Atwood levelegs system?
Reconnect jack to power. Manually extend individual jacks for 10 seconds by holding down the EXT key and the two jack keys that make up the camper corner of that jack. Listen to insure all jacks move when manually activated. Press RET and ALL to retract all jacks. 2 RED AND GREEN LIGHTS COME ON FOR A SPECIFIC JACK LOCATION Cause:
When to use levelegs system trouble shooting guide 9?
LEVELEGS™ SYSTEM TROUBLE SHOOTING GUIDE 9 Effective: 11/21/07 Guides are only intended for use on Atwood products by service technicians who have successfully completed Atwood® training. This guide should be used in conjunction with the appropriate Instruction Manual provided with the product and any applicable Industry Standards.
Solution: Put system in error mode by disconnecting one jack from power and pressing RET and ALL. Reconnect jack to power. Manually extend individual jacks for 10 seconds by holding down the EXT key and the two jack keys that make up the camper corner of that jack. Listen to insure all jacks move when manually activated.
1. Insure vehicle engine is running, transmission is in park and park brake is set. 2. If emergency stop was activated by pressing any keypad button, press ‘RET’ and ‘ALL’ to reset legs. 3 AUTO POSITION DOES NOT LEVEL THE COACH Cause: The last position in memory was not level. Solution: Leveler System always returns to position in memory. 1.
How much does a Visone leveling system controller cost?
USED RV/MOTORHOME POWER GEAR ELECTRIC JACK CONTROLLERS. READY TO SHIP. CALL VISONE RV (606) 843-9889. USED RV/MOTORHOME HWH LEVELING CONTROL BOXES. READY TO SHIP. PRICE $700.00 + $23.99 SHIPPING. CALL VISONE RV (606) 843-9889.
