Why is my Atwood 6 gallon water heater not working?
When the spark is present, but there’s no gas, chances are the issue is caused by incorrect gas pressure. Set your inlet pressure at 11”W.C. with a minimum of two gas appliances running at the time.
What causes pilot outage on Atwood water heater?
A blocked U-tube can also cause pilot outage. Clean the tube and get rid of any obstruction there is. You should check the gas pressure and ensure it is in accordance with the recommendation of the manufacturer, in this case, Atwood.
Can a 5 th water heater be used in 5 th vehicle?
Not only compatible for 5 th wheeled vehicles, but this water heater brand is also compatible with many other types of recreation vehicles such as motor homes and travel trailers.
When the spark is present, but there’s no gas, chances are the issue is caused by incorrect gas pressure. Set your inlet pressure at 11”W.C. with a minimum of two gas appliances running at the time.
Where are the switches on an Atwood water heater?
Often there is one inside the RV, may look like a typical 120v wall switch. Sometimes a second switch is in the WH compartment to make sure the element doesn’t get turned on when the tank is drained for winterizing. Yes, no extra switches.
When did the Atwood water heater service manual come out?
INTRODUCTION The 2004 edition of the Atwood Water Heater Service Manual is a resource created to help service technicians identify Atwood product by serial number, diagnose service problems and efficiently and effectively process warranty claims.
A blocked U-tube can also cause pilot outage. Clean the tube and get rid of any obstruction there is. You should check the gas pressure and ensure it is in accordance with the recommendation of the manufacturer, in this case, Atwood.
Often there is one inside the RV, may look like a typical 120v wall switch. Sometimes a second switch is in the WH compartment to make sure the element doesn’t get turned on when the tank is drained for winterizing. Yes, no extra switches.
What to do if your water heater is not working?
If you have the manual for the WH, there is also a thermostatic E.C.U. control that could be tripped or bad, not passing current to the heating element. A troubleshooting manual. There is usually a thermostat and an over temp cut out. The OT is usually resetable but not worth it…just replace both as they are cheap.
What’s the temp of the Atwood 6 gallon water heater?
Atwood 6-gallon water heater unit is pre-set at a temperature 140-degree Fahrenheit, which is adjustable from 110 to 150-degree Fahrenheit; this unit is operated on propane gas and can only be ignited inside of the trailer using an on/off remote switch.
Why is my Atwood water heater not working?
If you use a multimeter on the electric element, you could look up the specifications for the element and see if it reads proper ohms. Sometimes if an element has been turned on when no water in the tank, it will overheat but not burn out. It can then, however, cause current leakage that can trip a GCFI, but that should be a different circuit.
If you have the manual for the WH, there is also a thermostatic E.C.U. control that could be tripped or bad, not passing current to the heating element. A troubleshooting manual. There is usually a thermostat and an over temp cut out. The OT is usually resetable but not worth it…just replace both as they are cheap.
What is the DSi FAULT light on Atwood RV water heater?
I spoke with my contact at Dometic (who took on the Atwood water heaters) and they said that the DSI fault light on the switch for your Atwood RV Water Heater # AT94022 (GC10A-4E) will only come on for two reasons.
Why does the pilot light go out on my water heater?
A thermocouple is a device that senses the heat of a pilot and lets the gas flow to the burner. If the thermocouple is malfunctioning, it doesn’t allow the gas to run through the pilot and the burner. In return, the pilot light goes out repeatedly and would not stay lit.
What are the common problems with water heaters?
13 Common Water Heater Problems (Tricks to Fix) 1 1. No hot water. If you have no hot water, there are several possible reasons, and you need to work through each of them methodically to eliminate 2 2. Not enough hot water or water not hot enough. 3 3. Water too hot. 4 4. Water takes too long to heat. 5 5. Low water pressure.
What happens when the pilot light goes out on a water heater?
If the lever is set to “OFF” turn it to the “ON” position. The pilot light ignites your water heater’s burner to heat the water. So if the pilot light goes out, there’s nothing to ignite the burner and heat the water. You’ll need to remove the cover of your water heater to inspect and relight pilot light.
Where is heater element of Atwood water heater?
The water heater element on your Atwood Gas and Electric RV Water Heater # AT94022 is located behind the gas line. Follow the two red wires (see attached photo) which are power wires connected to the back of the heating element to either unscrew or unbolt it.
Where is the hot water heater on a RV?
The RV water heater has a water line at the bottom where the cold water goes in. On top of that line, there is a hot water line that feeds your pipes. If there is a middle pipe that connects these two lines, congratulations, you have just located the RV’s bypass valve.
How does a hot water heater work in a RV?
Your RV hot water heater runs on electricity or propane gas. Turning it on ignites the flame and it takes a couple of hours to have steaming, hot water to use. With an RV washer, the hot water will get used up quickly, but it fills up fast and again, heats rapidly. This is the unit from outside the camper. You can see it has the place to light it.
Why is there no hot water in my tankless water heater?
If you get no hot water when only one hot water appliance is running and you have a gas tankless unit, make sure that: You’ve paid your gas bill (your tankless water heater can’t heat water without a steady gas supply!) Your water heater vent is unobstructed (be careful—these are usually located on the roof)
What happens when your Atwood water heater gets too hot?
Atwood water heaters have a safety mechanism that cuts off electricity when it senses a power surge or if the system gets too hot. Here is how to reset your Atwood water heater.
Is the Atwood 6 gallon water heater an incredible piece?
You would like to know every single thing about the water heater. Those who have never purchased an Atwood 6-gallon water heater may question how a water heater can be considered “an incredible piece” when the reason these people are here in the first place is to get something to help them troubleshoot their water heater.
What kind of circuit board do I need for my Atwood water heater?
The quickest way to test a circuit board for your water heater is to use the circuit board from your Hydroflame furnace if you have one. The 8500 or 8900 models are the most compatible with your Atwood heater and should plug in easily. There will be the same 20-second delay that happens on your furnace when you power up the water heater.
What to do if your water heater has no hot water?
Atwood water heater has no hot water. 1 If you have an electric water heater, rule out any power problems first. 2 Check if the bypass valve is off or on. 3 Look out for any open faucets. 4 Check the temperature selector and reset the water temperature again. 5 Check the handle on the bypass valve line.
Why is my Camping World water heater not working?
Regardless, taking it back to Camping World, still under warranty. At the WH, there will be a thermostat and an over temperature cut out that turns the power on and off. Check for power at that point. The OTC has a reset button on it if it gets tripped by over heating.
What kind of air conditioner does Damon intruder have?
ENGINE AIR CONDITIONER Erratic speedometer on 2000 Damon intruder. Damon intruder I have a 96 Damon ultrasport. Wanting to do a tune-up on it Furnace does not do anything when turned on. Previous owner I’m looking at a 2002 UltraSport. There is a couple of Living room slide failure. 2002 damon intruder. I’m trying
Why is my water heater not working in my RV?
Refrigerator heats up and lights up but will not get cold. One slideout works fine. The other does not work at all. Slide out will not come in. The right side of the slide out Our water heater is leaking. It is coming from the atwood Cruise control will not come on all of the time. It does The high beams turn off when we hit a bump!
What’s the model number of my 2007 intruder?
I have a 2007 Intruder Damon 337 model number to. 337. Two Battery hook up on house batteries of my 2008 Damon Astoria.
What kind of tank does Atwood water heater have?
Additionally, Atwood water heaters have aluminum tanks that act as anode rods, thus the situation is a bit different for these. Now that you know the essentials about your onboard RV water heater, Dave has a few extra expert tips for operating and maintaining your specific unit.
How does an anode rod work on a hot water heater?
The anode rod has metal in it that is supposed to oxidize in place of the steel in your tank. This prevents your tank from leaking. When the metal is gone the steel core and your tank start to rust, thus discoloring the water. See ‘ Hot Water Heater Anode Rods ‘ for information on the anode rod.
Why is my gas hot water heater not working?
The other less common problem would be the gas valve. A bad gas valve will not allow any gas to go to the burner or pilot light. If the pilot light lights and then shuts off it is not the gas valve. If it won’t light at all, see the article, ‘ Fixing Hot Water Heater Gas Valves ‘ for the issues surrounding this device.
What should I do if my RV water heater is not working?
The last step of the RV water heater troubleshooting process is to turn off the LP system to check for a spark. If you don’t get a spark, your system could have an electrode that is bent or carbon grounding. Again, easy fix, quick solution. Okay, but what if you get through each of these steps and still can’t figure out what’s wrong?
Why does my water heater not stay lit?
This may be one of the more common sources for the heater not staying lit. Its job is to detect the flame once the flame has been lit and there are several versions of this part. You will have to have the right model number from the old part to get a new one.
What should I do if my water heater does not heat?
If the igniter is getting voltage but does not glow, it is faulty and should be replaced. Clean dirty electrodes, and remove any obstruction in the main burner or burner orifice. Check whether the spark electrode is producing sparks, and replace it if defective. If the water heater does not heat, the pilot or gas valve might be defective.
Why is my Atwood RV water heater not working?
Bad Circuit Board Atwood Rv water heaters are famous for their faulty circuit boards. The design of it is horrible. If there is a problem with your circuit board, it won’t allow the gas to pass.
How does the pilot light work on a water heater?
When the water heater is first lit, a valve releases gas into the burner, and the pilot light ignites that gas. After about 30 seconds, heat from the ignited pilot light flame activates a simple electrical switch called a thermocouple which ensures that the gas supply to the pilot stays open and your water heater keeps functioning.
Why does my gas water heater keep going out?
If you can light your pilot light, but it keeps going out, the first item to check is the thermocouple. When the water heater is first lit, a valve releases gas into the burner, and the pilot light ignites that gas.
How long does a propane water heater last?
The water heater only goes on for a few seconds then shuts off. No hot water … read more Vocational, Technical or Tra… We have an atwood 7916 in water heater.
When does the Atwood water heater shut off?
My RV Atwood water heater… My RV Atwood water heater runs and doesn’t shut off when the water is hot. After 30 min., the pop off valve opens and starts to vent hot water. Show More Show Less Ask Your Own RV Question
The water heater only goes on for a few seconds then shuts off. No hot water … read more Vocational, Technical or Tra… We have an atwood 7916 in water heater.
When does the RV water heater shut off?
After 30 min., the pop off valve opens and starts to vent hot water. Show More Show Less Ask Your Own RV Question Share this conversation Answered in 2 hours by:
How do you reset an Atwood water heater?
Here is how to reset your Atwood water heater. Turn off the power to the Atwood water heater. Using a socket wrench, unscrew the nuts holding the thermostat junction box cover to the unit’s back, and pull the cover away. Locate the red reset button protruding near the heating element.
Why is there no spark in my water heater?
It is possible the gas valve is malfunctioning and is not allowing gas to flow in. There may be no voltage which will trigger the electric spark. You may have to replace the circuit board or the solenoid valve and you would need to check the E.C.O. Loose wires on the E.C.O. could be the problem.
How do you troubleshoot a water heater?
Troubleshoot water heaters giving warm water or small amounts of hot water. Check the temperature setting. Adjust the setting with a slotted screwdriver if necessary. Set the temperature between 110 and 125 degrees F. Check the cold intake tube and fastener ring.
How does the ignition of a water heater work?
A millivolt ignition system is a method of igniting gas furnaces, gas logs, and gas-fired water heaters. They utilize either a thermocouple or thermopile. These devices, when heated, provide the millivolts to a pilot solenoid valve in a gas valve. Thus the pilot light burning to heat the thermocouple or thermopile.
What is a power vent on a water heater?
“Power vent” is simply a term used to describe the way your water heater pushes out harmful combustion gases out your home. For some residences, depending on where your water heater is located, a power vent may be your only option.
Can a propane water heater be turned on While there is no water?
Hot water heater was turned on while there was no water in heater. Hot water heater was turned on while there was no water in heater. I have filled the system now but can’t get the water heater to fire. No power to reset button on counter near stove. Any suggestions? … read more We just purchased a 2007 Fleetwood Gear Box Toy Hauler Fifth Wheel.
Where can I get Atwood RV water heaters?
Atwood Water Heaters – Arizona RV Parts Center Who says that camping has to be ‘roughing it’? Enjoy a hot shower or cook with hot water with these RV water heaters from Atwood. Toggle menu Welcome to Arizona RV Parts Center!
What kind of switches are on an Atwood water heater?
AC 110 Volt Rocker Switches & Plates AC 110 Volt Switches & Outlets DC 12 Volt Accessories DC 12 Volt Switches All DC 12 Volt Switches 12 Volt DC Wall Switches w/ Plates DC 12 Volt Momentary Switches 20amp DC 12 Volt Rocker Small Switch 5-10amp DC 12 Volt Rocker Switch 10amp Power Converters (AC to DC) All Power Converters (AC to DC)
Where is the Atwood RV Parts Center in Victor AZ?
Enjoy a hot shower or cook with hot water with these RV water heaters from Atwood. Toggle menu Welcome to Arizona RV Parts Center! 1345 Highway 93 North Ste B2 Victor MT 59875 United States of America
What is the Atwood water heater control board number?
This will replace the control board in your older Atwood electric and gas combination or gas only water heaters and is designed to work with part number AT94191, AT96121, and AT96136.
How to replace a Atwood RV water heater control panel?
The Replacement Control Panel for Atwood Water Heaters # AT91367 fits the Atwood RV Water Heater # AT94191, # AT96121 and # AT96136, which are made in the USA. This control panel should have no problem lasting you more than a few months of continuous use. view full answer…
What’s the name of the Atwood propane heater?
Vocational, Technical or Tra… Attwood 8531-IV, Burner recycles. The fan comes on, burner Attwood 8531-IV, Burner recycles. The fan comes on, burner lights, burns for about 2 minutes, shuts down. Does the same in about 5 minutes on … read more Vocational, Technical or Tra… Atwood furnace model 8535. On Rv starts, runs, ignites for
Is there a propane heater that won’t shut off?
I have and Atwood propane water heater that wont shut off… Atwood 8531 iv dclp l/d furnace trouble code light bling twice Flame fault. Burner comes on then shuts off … read more furnace blower comes on. burner comes on for 17 seconds, then goes out for 30 seconds and then relights again. Does this over &over … read more
How to troubleshoot a bad Atwood ignition switch?
Leave switch off, go outside to heater and un-plug 4 pin connector. Go back inside and turn switch on Go back outside and plug in 4 pin connector, then heater will ignnite !! Seems like bad switch or perhaps control board, or ??? It’s the board. An interesting troubleshooting process.
What kind of igniter board can I use in an RV?
I usually keep a spare Dinosaur UIB-S universal igniter board on hand that can be used as a replacement in many RV furnaces, water heaters, and refrigerators. I usually keep a spare Dinosaur UIB-S universal igniter board on hand that can be used as a replacement in many RV furnaces, water heaters, and refrigerators.
What to do if your hot water heater is not working?
After checking each of these, if you still can’t find the reason why you have no hot water, it might be time to call a professional. If you have a gas heater, check to see if the gas valve is open.
Why is my electric water heater not working?
The most obvious reason an electric heater doesn’t work is that it’s not receiving any power. Start by checking the circuit breaker to see if it has been tripped. If it has, it’s an easy fix – simply turn it off and turn it back on again. You may also have to replace the fuse if it has blown. The next step is to check the high-temperature cut-off.
How to test the Atwood water heater thermostat?
How to Test Atwood Water Heater Thermostat. The best way to test this part on your water heater is by using a continuity tester. When the water is cold there should be continuity between the contacts. When the water is hot there should be no continuity.
The most obvious reason an electric heater doesn’t work is that it’s not receiving any power. Start by checking the circuit breaker to see if it has been tripped. If it has, it’s an easy fix – simply turn it off and turn it back on again. You may also have to replace the fuse if it has blown. The next step is to check the high-temperature cut-off.
Regardless, taking it back to Camping World, still under warranty. At the WH, there will be a thermostat and an over temperature cut out that turns the power on and off. Check for power at that point. The OTC has a reset button on it if it gets tripped by over heating.
What should I do if my water heater is not working?
Anyone have any ideas on what my problem could be. If you ae are comfortable working with 120 volts, use a VOM “volt ohm meter” to insure 120 volts is reaching the element, set meter in ac position and touch the leads to the wire connections, of course with cold water in tank, if voltage is there, your controls are working.
Can a faulty thermostat cause a water heater to turn off?
A faulty thermostat can trigger the reset button. If it’s defective, it won’t send a command to the heater elements to switch off when they reach the desired temperature. The heaters will continue to heat, and the reset button is the next line of defense.
How long does it take for 6 gallon water heater to heat up?
We only turn on our 6-gallon water heater when we need it so we don’t waste propane and 10 minutes is all it takes to heat up. A 10-gallon tank will take about the same amount of time to heat up.
Why is my Propane water heater not hot enough?
If your gas water heater recovers too slowly, the thermostat could be set too low, the burner assembly may need to be cleaned, the propane gas pressure may be too low, or the vent flue may need to be cleaned. But in most cases, it’s just using water faster than the water heater can heat water.
Where is the 110 volt heat in my Attwood water heater?
I’ve just lost the 110 volt heat in the Attwood 10 gallon GC10A-4E water heater in my 2005 Knight. I suspect the 110 volt heating element is dead. The propane side of the water heater works fine. It seems that the heating element is in the rear of the water heater, which won’t make it easy to repair.
What are the problems with the Atwood water heater?
Common issues with Atwood water heaters include pilot outages, insufficient hot water, electrode problems and gas burner ignition issues. Before doing any troubleshooting or repairs, turn off the ignition switch, and shut off the water supply to the water heater.
I’ve just lost the 110 volt heat in the Attwood 10 gallon GC10A-4E water heater in my 2005 Knight. I suspect the 110 volt heating element is dead. The propane side of the water heater works fine. It seems that the heating element is in the rear of the water heater, which won’t make it easy to repair.
Why is my 110 volt water heater not working?
My experience with RV electric water heaters has shown that the most likely failure is a high resistance connection in the 110 VAC circuit that has overheated due to the large current flow required for the heating element. Sometimes this is a wire nut or relay contact.
If the igniter is getting voltage but does not glow, it is faulty and should be replaced. Clean dirty electrodes, and remove any obstruction in the main burner or burner orifice. Check whether the spark electrode is producing sparks, and replace it if defective. If the water heater does not heat, the pilot or gas valve might be defective.
What should I do if my water heater pilot light won’t come on?
Ignite the flame with a long match while switching the knob to “pilot,” hold it in the position for 35 seconds. Once the pilot comes on, turn the knob back to “on.” If the above procedure proves futile, repeat the process, and elongate the waiting time to 60 seconds.
What to do if your water heater control valve is faulty?
Replace the control valve: Most times, if the control valve gets faulty, a technician will be able to repair it. However, if you want your water heater to last, and if you wish to avoid future expenses, then you should consider changing the main control valve entirely.
After checking each of these, if you still can’t find the reason why you have no hot water, it might be time to call a professional. If you have a gas heater, check to see if the gas valve is open.
The quickest way to test a circuit board for your water heater is to use the circuit board from your Hydroflame furnace if you have one. The 8500 or 8900 models are the most compatible with your Atwood heater and should plug in easily. There will be the same 20-second delay that happens on your furnace when you power up the water heater.
How do you troubleshoot a gas hot water heater?
If troubleshooting a gas water heater, make sure that the gas is on, then relight the pilot flame with a BBQ lighter at the base of the water heater. If troubleshooting an electric heater, make sure the heater is receiving electricity, then reset the thermostat by pressing down the red reset button on top of the thermostat.
