Why is my Aquabot not working?

AQUABOT STOPS RUNNING AFTER SHORT TIME It may run for a short period after turning power off and on. The most likely problem is the timer on or in the power supply. To check, when the robot stops, unplug the robot from the transformer and check for voltage at the power transformer outlet.

How do you change the drive belt on an Aquabot?

With the center pulley in the side plate, insert the metal end of the pulley into the center hole on the body, then pull the drive belts over the wheel tubes and into their respectful gear. Now fasten the side plate with screws and finish by pushing the bushings on the wheel tube and into the side plate.

Why does my Aquabot keep flipping over?

the likely problem is the float/handle. Make sure it moves freely and is always in the straight up position when on the bottom of the pool. If it’s not then it is the problem.

What is aqua bot?

You can dive straight in safe in the knowledge that you are swimming in pure, hygienically clean water. Our robotic pool cleaners feature the most powerful suction on the market, nothing escapes. The patented on-board smart navigation algorithm ensures that most efficient cleaning route is followed every time.

Can you leave Aquabot in pool?

It will clean for 4 hours and then turn off. The filter then needs to be cleaned out. Don’t leave it in when swimming.

How many drive belts are on an Aquabot?

The two (2) drive belts located behind the side plate on the drive motor side of the Aquabot, may be stretched or broken.

Why does my Polaris do wheelies?

What causes automatic pool cleaners to flip or do wheelies? The water level in a pool is one of the most common causes for this problem. Outside of the water, the motor can burn out within one hour — or within minutes if it’s really hot. Another cause of flips and wheelies is too much air in the unit.

Why does my pool vacuum keep flipping over?

The water level in a pool is one of the most common causes for automatic pool cleaners to flip over. When the water level on the skimmer is too high, the water line is too close to the coping. Not only can this cause flips and wheelies, but it also keeps the cleaner from performing correctly.

What to do if your aquabot is not working?

Turn on the robot for a maximum of ONE minute. Turn a wheel a little in each direction to unbind the motor. If this does not work, replace the motor. Assuming belts are good and installed correctly and a wheel is not falling out of the sideplate, you need a new motor. ROBOT MOVES, WATER PUMP IS NOT WORKING.

How can I test my aquabot Turbo Plus?

Voltage testing a two wire Aquabot Turbo transformer. The above photo is a 6 wire Transformer for Turbo Plus w/remote voltage test. 4) With the robot submerged, wiggle the cord between the handle and the motor. If the robot momentarily comes to life, replace or repair the cord. Check the cord plug end for broken contacts.

What’s the drive motor on an aquabot Turbo?

The drive motor in the Turbo is a white rectangle with a sloped end?, the black Bravo/Merlin motor has some round caps on it that look like they can be unscrewed to gain access, but I haven’t yet opened one. If you have any luck finding the motor, please post back! Good Luck!!! Enjoying this content? Support TFP with a donation.

How does an aquabot work in the pool?

The Aquabot drive system is actually a fairly simple design. It consists of a drive motor, a pulley connected to the rotating output shaft of the drive motor, belts that transfer that rotation to the wheel tubes (with the scrubbing brushes) and finally, the drive tracks. All this together allows your Aquabot to move around the pool.

How to troubleshoot aquabot Turbo T-Jet robotic pool cleaner?

Learn troubleshooting tips and tricks about the Aquabot Turbo T-Jet robotic pool cleaner from the the expert pool staff at The Pool Factory.

What to do if your aquabot doesn’t work?

If there is no motion and no obstructions, firmly grip one wheel and see if you can free the drive motor. If that doesn’t work you might consider taking your machine in for service. b) Be sure the cord is not tangled and/or damaged. d) Reverse handle direction and place your Aquabot at a different entry point after each use.

Why does my aquabot pool vacuum stop working?

I have an Aquabot turbo remote control robotic pool vacuum that has performed flawlessly for 6 years. When I try to run it now, with the black button on the power supply it will start momentarily. As soon as I let go of the button ( which should start a 7 hour timer cycle ) , the unit stops working.