Why does my Zodiac pool cleaner go in circles?
Sometimes it gets stuck in the corner of the pool by the steps; other times it goes in circles. This is most likely caused when pool cleaners are left in the pool 24/7. When the water is cold or cools off from a warm day, the plastic in the hose gets a memory and curls slightly.
Why is my MX8 not working?
MX8 Is Frequently Stuck at Steps Solution: You can troubleshoot the issue by ensuring that there is sufficient hose length supporting the cleaner’s operation. Try to adjust the length by extending or shortening it. If it doesn’t work, use the flow tester to verify that there is proper flow to the cleaner.
Why does my pool cleaner only stay in the deep end?
Another common cause of flow problems with the 360 is a clogged or dirty pool filter which is not allowing enough flow through the return for the cleaner to operate properly. You may need to backwash or change your sand (clean grids in DE or clean cartridge). If your filter is okay, you may have a clogged impellar.
Why does my barracuda get stuck?
As your Baracuda pool cleaner moves around the pool, it may become stuck at the stairs or ladder. If no one is around to move it, the cleaner will remain in that spot and not clean the rest of the pool. In some cases, the hose is too long, and shortening it will prevent the cleaner from moving to these areas.
How far should the back up valve be from the Polaris?
30″
The Polaris in-line back-up valve and float should be installed 30″ from the Polaris. Once installed, the hose should look like the one below.
What kind of pool cleaner does Zodiac MX8 use?
In this review, we’re going to look at the Zodiac MX8, a fully automatic, low to mid-range suction-side bot that offers aggressive cleaning in all types of in-ground pools. It does all this without compromising on energy efficiency. Thus, the pool remains pristine while the operating costs remain low.
Why is my Zodiac MX8 moving in small circles?
The great thing about the MX8 is that it an easy cleaner to work on. It is pretty well engineered but it is a gear cleaner so the parts that drive it will wear out. The first thing I show is if the cleaner is moving in small circles in the pool. I took this solution from Troublefreepools. Here is the actual link and solution from JGUY:
What are the problems with Baracuda pool cleaners?
Baracuda pool cleaners are designed to move across all of the floor surface so the entire pool is cleaned. In some cases, the cleaner may become stuck in a pattern and only clean certain areas of the pool. The length of the hose is an issue if this occurs, so ensure that the hose is long enough for the cleaner to cover the entire pool.
When does a Zodiac Pool Cleaner wear out?
It gets stuck inside the cleaner which keeps it from cleaning and moving around. The Zodiac MX8 also has an Achilles heel: it’s gear drive system. The gears wear out after about 12 or 18 months and needs constant replacement. The gears continue to wear out over the course of its pool cleaning life.
In this review, we’re going to look at the Zodiac MX8, a fully automatic, low to mid-range suction-side bot that offers aggressive cleaning in all types of in-ground pools. It does all this without compromising on energy efficiency. Thus, the pool remains pristine while the operating costs remain low.
The great thing about the MX8 is that it an easy cleaner to work on. It is pretty well engineered but it is a gear cleaner so the parts that drive it will wear out. The first thing I show is if the cleaner is moving in small circles in the pool. I took this solution from Troublefreepools. Here is the actual link and solution from JGUY:
What kind of suction does Zodiac Pool Cleaner use?
The Zodiac MX8 is ready to battle your pool’s toughest dirt and debris. The dual cyclonic suction enables the MX8 to move faster and deliver unsurpassed vacuum power, while requiring 30% less flow.
Do you need to replace bearings on Zodiac MX8?
You will need to replace the Engine Assembly and possibly the two bearings. Like the Zodiac Polaris cleaners I noticed there are several bearings in the MX8 cleaner. I would say after maybe five or six years all the bearings will need to be replaced to keep the cleaner working fine.
