Why does my Sundance 880 stereo not work?
I have a Sundance 880 series spa and shortly after a cold snap this winter my radio/stereo stopped working. All the lights are ‘off’ on it. 2. using a rod to press the reset button under the AUX cover. Nothing worked! What can I do next??
Where are the fuses on a stereo system?
The fuses are on the yellow and blue wires but always follow the wire schematic and always shut the power off to the spa before separating the power supply wires from the deck wires. To do this you need a multi-meter that checks for continuity and one that also reads DC voltage.
How big is the fuse for a jacuzzi?
Jacuzzi® Spa Fuse, 1.5 Amp Mini Slo-Blo, For (LED PCB) Circuit Board. USED IN: Jacuzzi® Fuse Chart This is a mini fuse 6760-120 as used in Sundance Spas and Jacuzzi hot tubs. 1/8 Inch Wide X 1/2 Inch Long. Jacuzzi Spa fuse chart.
What kind of fuses are used in a spa?
LittleFuse 4 Amp Fuse 229-004 is a small, slo-blo glass body fuse used on spa circuit boards. This Littelfuse cartridge is rated at 4a slo-blo. Amps: 4a Type: glass fuse Voltage: 125V Interrupting Rating: Vita Spa Bussman 8 Amp MDL Fuse. This fuse model VIT452153 or 452153 is rated at 8 amps.
I have a Sundance 880 series spa and shortly after a cold snap this winter my radio/stereo stopped working. All the lights are ‘off’ on it. 2. using a rod to press the reset button under the AUX cover. Nothing worked! What can I do next??
The fuses are on the yellow and blue wires but always follow the wire schematic and always shut the power off to the spa before separating the power supply wires from the deck wires. To do this you need a multi-meter that checks for continuity and one that also reads DC voltage.
Can a series Fuse be used on a low voltage circuit?
Connecting fuses in series does not increase the rated voltage of the combination, nor of any one fuse. Medium-voltage fuses rated for a few thousand volts are never used on low voltage circuits, because of their cost and because they cannot properly clear the circuit when operating at very low voltages.
What kind of voltage does a Littelfuse Fuse have?
Generally, fuses have a DC voltage rating that is half of the maximum AC voltage rating. (Example: LLSRK_ID – 600 VAC, 300VDC) Consult the factory for specific DC voltage ratings. Does Littelfuse have an Environmental Health and Safety Policy?
What to do if your TV remote control is not working?
If TV buttons can be operated, proceed to Section B: Checking items of the remote control. If TV buttons cannot be operated, proceed to Step2. NOTE: Depending on the model, the positions of TV buttons vary. Check the sides, back, front, and top of your TV. Check that the lamp (power lamp/standby lamp) on the front/bottom of the TV is on.
Why does my radio not work on my Deck?
If there is a break in the wire or wiring harness or moisture in the harness this could keep it from working. If the wire and wiring harness is ok then you have a bad sub woofer. Check for proper voltage with a multi-meter on the harness coming from the deck. Thanks for your very thorough response! I’ll start with the fuses!
What to do if your stereo doesn’t turn on?
If your power supply and fuses are good and your reset actions don’t correct the stereo not turning on then you have a bad deck. As a sidebar check the area inside the equipment bay and check the integrity of all the wires in this area.
Is there a wired remote for a marine stereo?
Wired Remote for Sony Marine Stereo. Comes with Remote, Cable, and Mounting Ring. . . Only 2 left in stock – order soon. . . .
Why does my Sundance spa go into Oh error code?
Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code
What happens when Sundance spa goes into watchdog?
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.
What to do if your Sundance spa switch is defective?
Disconnect wires from Switch terminals. Set ohmmeter in the continuity position. Measure resistance across switch terminals for infinite resistance with pump off. If continuity is measured with pump off, the switch is defective. (Or debris blockage, l which you have to remove switch and inspect.
