Why does my spa pump not turn on?
Rick alot of the Balboa paks have a lockout for the pump ie when the water is cool like after a fresh fill the circulation pump will work til the spa heats within a certain range of your set temperature so like 20 degrees within your set temp. That could be the reason why the jet pump won’t turn on.
Do you need to change the filter cycle in a Master Spa?
It’s important to set your filter cycle to properly maintain the condition of the water. The duration of your filter cycle is influenced by how much your Master Spa is being used and by how many people, so you may need to be adjusting the filter cycle on a regular basis.
What should I do if my hot tub Wont Stop Running?
Turn the breaker or power off for a minute and turn it back on again without pressing any of the controls or buttons. The tub should start up at a default 100F temp setting and start a 1-3 hr filter cycle with the pump running low speed until the filter cycle ends or longer if still heating.
When do I Turn on the hot tub?
If you do need it due to your hot tub or swim spa being used a lot you can turn it on by pressing 2 again. We’ll set this cycle to run from 10:30 p.m. to 11:30 p.m. The lock indicator is shown when either the control panel has been locked to prevent unwanted use, or if you don’t want the settings to be changed.
Rick alot of the Balboa paks have a lockout for the pump ie when the water is cool like after a fresh fill the circulation pump will work til the spa heats within a certain range of your set temperature so like 20 degrees within your set temp. That could be the reason why the jet pump won’t turn on.
It’s important to set your filter cycle to properly maintain the condition of the water. The duration of your filter cycle is influenced by how much your Master Spa is being used and by how many people, so you may need to be adjusting the filter cycle on a regular basis.
When do you turn off the jet pump on a caldera spa?
If you place the jet pump on high during the filter cycle, the filter icon will blink in the display and not resume until 10 minutes after the jet pump is shut off. Press the “Set” button to deactivate the Spa or Temperature Locks.
If you do need it due to your hot tub or swim spa being used a lot you can turn it on by pressing 2 again. We’ll set this cycle to run from 10:30 p.m. to 11:30 p.m. The lock indicator is shown when either the control panel has been locked to prevent unwanted use, or if you don’t want the settings to be changed.
Why is the increase button on my spa not working?
If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance spa. Sundance series 880 spa temperature increase button does not work. All other panel functions work. John if the decrease button works and the increase button does not you could have a bad topside control.
What does the orange light on a spa side control mean?
These are called Spa Side Controls, they have built in air buttons and orange indicator lights. One of the indicator lights says heater, this light comes on regardless if the spa is heating or not. Do not troubleshoot using this light, it could confuse you. Why Does The Hi Limit Switch Trip? The #1 reason is filter related.
Why is the heating element on my spa not working?
If for any reason one of these components fail then the required voltage to the coil will be jeopardized and the contactor will not close in order to send power to the heating element. As mentioned above, it is usually one of these components that will cause a spa not to heat.
Why is the flow switch on my jacuzzi not working?
If you have a FL 1 error code and the flow switch is in the open position, most likely you have an issue with the filters or the circulation pump not moving water. If you just filled the tub, the circulation pump may be air locked and will need to be primed.
What to do if your jacuzzi tub does not turn on?
If the jetted tub will not turn on or the pumps will not start at all, turn off the tub. Make sure the tub is connected to a power supply, that power in the room is not out and that you have completely depressed the “On” button for the jets. If there is no voltage, the pump is not connected to the power supply.
Where is the reset button on my jacuzzi?
Drain the water using the main control panel and turning the valves below. Turn your spa off using the main control panel. Clean the spa completely, paying special attention to the jets and filter. You will find a reset button typically on the heater unit.
What happens when you take the cover off a jacuzzi?
Filter and circulation pump is activated and the heater is deactivated DO NOT GET INTO THE WATER. Take off the spa cover to allow the water to cool down and reduce thermostat settings. Switch spa to Programmable Mode in order to turn the heater on solely during programmed filter cycles.
