Why does my slide out Stick after 8 inches?

If your other slides operate quickly and this one sticks for the first 8 inches, it sounds like there is something that is rubbing or sticking when the slide first starts in. The fact that it moves in normally after the first eight inches suggests that the motor is working well. You haven’t indicated what model and year motor home you have.

Can a slide out slide out all at once?

My slide out will not slide out all at once. It starts out then stops. I wait 10 seconds or so push the button then it My slide out will not slide out all at once.

How big of a wrench do you need to move a slide?

If you disengage that lock switch you should be able to put a 3/4 inch wrench/ratchet on the nut to move the slide. If there are two motors on the slide it will require two people and the wrenches need to be turne simultaneously (slide ends within 1 to 2 inches of each other) so do the wrench turns together.

Which is the correct way to do the slide rule?

Use the folded scales. In this example, set the left 1 of C opposite the 2 of D. Move the cursor to 7 on CF, and read the result from DF. Use the CI inverted scale. Position the 7 on the CI scale above the 2 on the D scale, and then read the result off of the D scale below the 1 on the CI scale.

My slide out will not slide out all at once. It starts out then stops. I wait 10 seconds or so push the button then it My slide out will not slide out all at once.

What happens when hydraulic slide starts and stops?

Also, just like pulling your RV from a stop, when the hydraulic pump pulls from a stop, it has to overcome the inertia of the slideout’s resting position. And in some cases, the slideout has to be raised a little from its resting position. The additional work effort by the pump at these times requires additional mechanical power.

Where are the rods that drive the slide out?

The opening is just to the left and below the yellow wire screw caps (first photo with old motor) Square rods that drive the slide bars are attached on both sides of the motor gear box (second photo with new motor). The slide-out that was stuck open is also shown below.

Where does the power come from to power the slide in?

One to power the slide in and one to power the slide out. input to the common point of the repay pictured is pictured; but that power should come from a larger fused supply with the key switch only controlling the relay coils of the in and out relays / with a limit switch to stop the slideout travel and to stop the slide at a in or park point.

Is there a stop button on the slider?

There is a section at the end for customizing. The slider does feature a stop/start button and the animation goes a little farther than simply sliding to the left. The markup is extremely light. Simply a wrap that contains the area and hides overflow, then a “mover” inside it to which does the sliding, then slides inside of that.

When do you move the slide on a coach?

Our manufacturer suggests that we move the slides when the coach is plugged into shore power or with the generator running. If neither of these are possible they say the slides should be moved only with fully charged batteries. On the Disco, the driver side slide fits flush to the floor when extended.

What’s the best way to retract slideouts?

Every seminar I have attended says to always operate the slides at road level, which means to put them out before leveling the coach and bring them in after raising the jacks. This sets the coach “true” so the slides are not “torqued”, which can cause binding and damage.

How to align Power slideout and adjust power slide rail?

Adjust the gear timing by sliding the idler rail side of the room to the proper position (Measure to ensure the same distance from the frame as the drive rail side).* Push the idler drive shaft back into position, engaging the gear onto the gear rack. Reinstall cotter pin into idler drive shaft. Extend…

What does it mean when your slideout is out of alignment?

There is. The technical term for describing our slide being out of alignment is: the rails are out of synch, or the gear timing is off. So, technically speaking I adjusted the timing of the rails supporting our slideout to realign the room.

Why does my slide out move when parked?

You might move the slide out and just a little and measure all four corner distances from the outside wall and the slide wall that seals to the main wall. Any difference could indicate an out of adjustment issue.

Why does the side of my slide come in square?

The Side should come in square! If the slide is square to the side wall, then there is an issue – possibly some thing between the front inside wall restricting the slide in that corner. You might move the slide out and just a little and measure all four corner distances from the outside wall and the slide wall that seals to the main wall.

What kind of motor does a slideout use?

His slideout operated with an electric motor driving 2 parallel rack and pinion sets from a single shaft. I don’t know a lot of the details, but it turned out that at the end of the stroke, the slide out dropped so that one of the rack and pinion sets changed center distance enough that the gear teeth disengaged.

What makes a slideout move in a car?

It keeps the motor locked so the gears do not move. The gearing ratio is like 50 to 1 to get the power required to move the slides and this also makes for a good breaking system to keep the slides locked in position. Rich. It is Power Gear.

Are there any problems with the slide out?

Most slide out problems are not that difficult to trace and then solve. There will be those that require the help of a professional technician to repair. The key would be to get to know your system and learn when the task is beyond your abilities to handle .