Why does my hurlcon spa heater not turn on?
When all is working correctly you should have no problems. The most common problem with spa heaters and why it sometimes wont fire up is due to low water flow. Low water flow means the water flowing thought the heater is insufficient. The heater sensors this and wont turn on. Hurlcon heaters need 150 litres per minute to operate correctly.
What are the troubleshooting charts for hurlcon heater?
If you have your original Hurlcon heater manual you’ll be familiar with the troubleshooting guides below, if not here they are – the general Hurlcon Spa Heater Troubleshooting charts. They lists some of the basics, if your problem is not listed then please read on.
Where is the serial number on a hurlcon JX heater?
Hurlcon JX Heaters Serial Number – This one will be external on the cabinet side panel, generally on the left side panel. ( Download JX Heater Manual) Hurlcon MX Heaters Serial Number – Remove the front panel and you will see the sticker on the panel behind the gas valve.
What to do if your heater temperature sensor has corroded?
If the temperature sensor has corroded it will need to be replaced. The temperature sensor is a pink wire with a brass head on it that sits in the brass sensor pocket located on the heater inlet manifold. Generally you would replace both the sensor lead and brass sensor pocket.
What is the display on the Hayward pool heater?
Hayward pool heater display is blank Power is on to heater pump is running just filled propane tank and valve is on Hayward pool heater display is blank Power is on to heater pump is running just filled propane tank and valve is on – Answered by a verified Pool and Spa Expert We use cookies to give you the best possible experience on our website.
Can You get Me the model number of the pool heater?
Some heaters have a switch on the door that will prevent start up if the access door is opened. Jerry : Can you get me the model number of the heater? This way I can check the wiring diagram to see if there are any fuses or other links that may be preventing the power from getting to the control panel.
What to do if your pool heater is not working?
Jerry : You may want to pull the fuses and check them with an ohm meter for continuity, sometimes the fuse looks good, but there is a small fault that is not allowing power through. Customer: I’m not a technician and there may be more fuses that I can see…..
Why is my Hayward pool heater not starting?
Jerry : It sounds like there may be a problem with the main power coming into the unit. Some heaters have a switch on the door that will prevent start up if the access door is opened. Jerry : Can you get me the model number of the heater?
Why does my spa heater not fire up?
The heater temperature sensors are constantly sensing the water temperature in and outlets. When all is working correctly you should have no problems. The most common problem with spa heaters and why it sometimes wont fire up is due to low water flow. Low water flow means the water flowing thought the heater is insufficient.
Why does my Raypak hot water heater not ignite?
I do not understand why Raypak would have a spark igniter AND a pilot. If the unit continues to spark after the pilot is lit, you most likely have a bad system board. A lot of home furnaces are done the same way. It has to do with how the flame proving circuit works for that style of control board.
Why does my gas heater on my patio not work?
As with other gas appliances, one obvious reason they fail to work is that there’s no gas. Look toward the base of the heater and take out the gas cylinder. If it’s light in weight, it may be empty, and you should replace it with a full one.
When all is working correctly you should have no problems. The most common problem with spa heaters and why it sometimes wont fire up is due to low water flow. Low water flow means the water flowing thought the heater is insufficient. The heater sensors this and wont turn on. Hurlcon heaters need 150 litres per minute to operate correctly.
What to do if your spa heater does not heat?
Once they are removed, tape them together; turn the thermostat dial down to the off position, and turn the power back on. Make sure the spa is on the heater/filter cycle and water is flowing from the jets, turn the thermostat dial up while watching the contactor, if it closes when doing this, then re-test the heater using the amp-meter.
What to do if your patio heater does not light up?
If the patio heater has an electronic ignition system, make sure that there is a spark. If there is a spark but the heater will not light up, try using a lighter or burning spill to light the gas.
How to tell if your hot tub heater element is the problem?
With the spa on, test both of the leads on the element at the same time. If the meter is reading 240v, the element is the problem. If the meter is reading zero, the problem is with the circuit board. With the spa on, test both of the leads on the element at the same time. If the meter is reading 120v, the element is the problem.
