Why does my hot tub have a Flo message?
The message can also be caused by soiled filters, plugged or bad Flow switches or a bad connection from the Flow switch to the PWA. In rare instances a bad PWA could cause a solid FLO message. If the pump checks out try and look at the filter, the circ line, the wiring to the Flow switch and the Flow switch.
What to do if your hot tub has a bad flow switch?
If there is no water movement in the spa check to see if there is hair or debris wrapped around the Flow Switch paddle. If this is not the case you could have a bad Flow Switch. If all else fails contact our Service support team to book a diagnostic and repair of your spa. Replies Theresa Nielsen January 03, 2015 Reply
What are the error codes on my hot tub?
Today, I want to talk about two error codes that we get on the top site display. One is FLO and the other is FLC. These two errors deal with the flow going through the heater and the pressure switch. The first thing that you want to do if you get these error codes, is actually take your breaker and turn it off and then turn it back on.
Where is the pressure switch on a hot tub?
To adjust the pressure switch, it is located right here on the heater, and there is an adjustment on top. On this one it’s a plastic dial and on some it’s a little plastic screw. What we want to do is take and turn this up to one turn clockwise, slowly until that error code goes away.
The message can also be caused by soiled filters, plugged or bad Flow switches or a bad connection from the Flow switch to the PWA. In rare instances a bad PWA could cause a solid FLO message. If the pump checks out try and look at the filter, the circ line, the wiring to the Flow switch and the Flow switch.
If there is no water movement in the spa check to see if there is hair or debris wrapped around the Flow Switch paddle. If this is not the case you could have a bad Flow Switch. If all else fails contact our Service support team to book a diagnostic and repair of your spa. Replies Theresa Nielsen January 03, 2015 Reply
Why does my hot tub have no water movement?
If your Topside is displaying a Solid FLO message you will have no water movement in the spa. Inspect your Flow Switch for hair or debris wrapped around the paddle. Also check to see that your spa is not in Summer Logic (spa water reaches 2 DEGREES above the set temperature).
What to do if your hot tub has a GFCI breaker?
If this is the case turn the GFCI breaker off to the spa and remove your filter. Make sure there is nothing in the filter area and turn your GFCI back on again.
How to troubleshoot a flashing Flo for a spa?
First verify your spa is receiving the specified incoming voltage into the circuit board as well as out of the circuit board to the transformer. Also, check all fuses for continuity. Next, check the service tag on the side of your circulation pump. This will tell you approximately what voltage your circulation pump should be getting.
Why is my Sundance spa Flo not working?
If you ave one and the jets work, it’s even more likely that it’s a bad pressure switch. Good luck. If the circ pump is buzzing and hot to the touch most likely it is the culprit. If you can remove the equipment access panels, locate the flow switch to see if it is in the closed position or even moving/fluctuating.
What to do if your hot tub has a flow sensor error?
1. I am getting a Flow Sensor Error. Solution 1: If you get a flow sensor error on your hot tub, you will want to turn off your spa. Make sure your spa is full. Then you will want to pull out the filter and put the hose in the hole. Turn the hose on full blast for about 25 seconds.
What does it mean when your hot tub says flow error?
A hot tub flow error indicates that there is a problem with the flowing of water through the hot tub heater. Some of the most common hot tub error codes are FLO, FL1 or FL2, and are picked up by flow or pressure switches.
First verify your spa is receiving the specified incoming voltage into the circuit board as well as out of the circuit board to the transformer. Also, check all fuses for continuity. Next, check the service tag on the side of your circulation pump. This will tell you approximately what voltage your circulation pump should be getting.
How to diagnose a Flo message on a hot tub?
Answer: When diagnosing a FLO message it is important to consider that there are 3 different types of FLO messages that your Spa’s logic is capable of displaying (a Solid FLO message, a Flashing FLO message and a Solid FLO2 message). First determine which message you are seeing.
If you ave one and the jets work, it’s even more likely that it’s a bad pressure switch. Good luck. If the circ pump is buzzing and hot to the touch most likely it is the culprit. If you can remove the equipment access panels, locate the flow switch to see if it is in the closed position or even moving/fluctuating.
What should I do if I get a Flo error on my spa?
Some of them may require a skilled technician to come out and work on your spa for you. 1. The first thing to do if you have a FLO error is to remove your filter and clean it. A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter.
What to do if you get flashing Flo error code?
1. First thing to do is remove your filter (s). If the error goes away, then it would be a good idea to replace those filters. While it is not a 100% guarantee this is your issue, it could be a contributing factor. 2. Next thing to do is open your cabinet and take a look at your flow switch.
What does Flo error on my Sundance spa mean?
A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter. Even if you think it should be fine, give it a try. Sometimes we can’t see the problem with our eyes.
Some of them may require a skilled technician to come out and work on your spa for you. 1. The first thing to do if you have a FLO error is to remove your filter and clean it. A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter.
Why does my hot tub have an error code?
Some of the most common hot tub error codes are FLO, FL1 or FL2, and are picked up by flow or pressure switches. The most common causes for this are a dirty or damaged filter, low water levels, air in the pipework or a faulty pump or sensor..
What should I do if I get a Flo error?
1. The first thing to do if you have a FLO error is to remove your filter and clean it. A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter. Even if you think it should be fine, give it a try.
Is there an error on my hot tub?
An error occurred while retrieving sharing information. Please try again later. Testing a HOT TUB Pressure Switch / Hot Tub Water Not Heating?
If your Topside is displaying a Solid FLO message you will have no water movement in the spa. Inspect your Flow Switch for hair or debris wrapped around the paddle. Also check to see that your spa is not in Summer Logic (spa water reaches 2 DEGREES above the set temperature).
Why does my hot tub say Flo Dr?
FLO, DR. or DRY errors commonly occur due to debris and blockages. They can usually be easily fixed with some simple hot tub troubleshooting steps, such as cleaning your filters and topping off your water level. Learn more about what these error messages actually mean and what you can do to fix it.
Why does my hot tub have an error message?
Hot tub control panel error messages – If your hot tub control panel has been showing an error message you will want to know how to clear it. Even if you have sorted out the problem that the error message is indicating it might still be continuing to show as a problem on the control panel.
What to do if your hot tub is not working?
If the error signal continues on the control panel then you will need to consult your hot tub manual to see what the problem is. If the control panel simply seems not to be working you can check the connections to it and also see if any water has got in it which could be the problem.
When do I need to reset my hot tub control panel?
If your hot tub control panel isn’t working then when it can be really frustrating. Having said that, sometimes all you need to do is a simple reset on your hot tub control panel to clear the problem and to get it back into action.
