Why does my hot tub have a flashing Flo message?
If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter. It’s very important to remember that if you just finished fresh filling your spa then you could also have had an air lock that caused a Flashing FLO message. By removing the filter you just removed the air lock.
Why does my Spa have a Flo error?
On your spa’s heater, there are sensors that read water pressure or there may be a pressure switch. These determine the error. The most common reasons for the FLO error message are dirty filters, a low water level, clogged circulation pumps or bad sensors. The first thing you should do is check your tub’s water level.
What to do if your hot tub has an error?
Reset the tub GFI breaker to see if the error clears. If this simple fix doesn’t solve the problem, it may be time to check your hot tub filter. The next thing to do is remove your tub filter cartridges. If the error clears, it was likely the fault of dirty filters.
When to use Spa when temperature is flashing?
Do not use spa when temperature is flashing or the OH message is displayed. HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational. SESH = Sensor short, nonfunctional.
If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter. It’s very important to remember that if you just finished fresh filling your spa then you could also have had an air lock that caused a Flashing FLO message. By removing the filter you just removed the air lock.
On your spa’s heater, there are sensors that read water pressure or there may be a pressure switch. These determine the error. The most common reasons for the FLO error message are dirty filters, a low water level, clogged circulation pumps or bad sensors. The first thing you should do is check your tub’s water level.
Why does my hot tub keep giving me an error message?
The next thing to do is remove your tub filter cartridges. If the error clears, it was likely the fault of dirty filters. Clean your filters before putting them back in your tub to ensure the error message doesn’t pop up again. If your hot tub is still showing the message, it may be your circulation pump causing the problem.
What to do if your hot tub has a bad flow?
If your spa is in Summer Logic, cool the water off by opening the cover and or adding some cold water to the spa. If neither of these are the case you could have a bad Flow Switch or a bad connection to the Flow Switch. If all else fails contact our Service support team to book a spa diagnostic and repair of your spa.
What does a flashing Flo on a circ pump mean?
Typically Solid FLO msgs are related to a blockage, bad Flow switch and or connection, summer logic, bad PWA. Typically the circ pump would be off with a Solid FLO. A Flashing FLO msg could mean other things like a soiled filter, low water level, stuck weir door (not enough water supply to circ pump).
What to do if your hot tub has a GFCI breaker?
If this is the case turn the GFCI breaker off to the spa and remove your filter. Make sure there is nothing in the filter area and turn your GFCI back on again.
Typically Solid FLO msgs are related to a blockage, bad Flow switch and or connection, summer logic, bad PWA. Typically the circ pump would be off with a Solid FLO. A Flashing FLO msg could mean other things like a soiled filter, low water level, stuck weir door (not enough water supply to circ pump).
If this is the case turn the GFCI breaker off to the spa and remove your filter. Make sure there is nothing in the filter area and turn your GFCI back on again.
Why does my hot tub have no water movement?
If your Topside is displaying a Solid FLO message you will have no water movement in the spa. Inspect your Flow Switch for hair or debris wrapped around the paddle. Also check to see that your spa is not in Summer Logic (spa water reaches 2 DEGREES above the set temperature).
Why is the blinking light on my spa not working?
Sensor plugged into jack B is not working. SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected.
What does blinking red light on hot tub control panel mean?
Blinking Red Light. A blinking red light on the control panel may indicate it needs to be reset. For most models you will turn off the power to the spa for a minute or two and then turn it back on. Turn on the lower amp breaker first if you have a hot tub powered by 240 volts.
If your Topside is displaying a Solid FLO message you will have no water movement in the spa. Inspect your Flow Switch for hair or debris wrapped around the paddle. Also check to see that your spa is not in Summer Logic (spa water reaches 2 DEGREES above the set temperature).
When do you get error code on your hot tub?
Updated on: December 23, 2020. Posted on: March 29, 2018. You likely look forward to a hot tub soak every day. So, when you see an error code on your spa’s control panel, you might worry that you’ve lost your chance. But don’t fret!
Why is my Sundance spa Flo not working?
If you ave one and the jets work, it’s even more likely that it’s a bad pressure switch. Good luck. If the circ pump is buzzing and hot to the touch most likely it is the culprit. If you can remove the equipment access panels, locate the flow switch to see if it is in the closed position or even moving/fluctuating.
Do you have hot tub Flo error code on your hot tub?
If you have a Hot Tub FLO Error Code, this usually means there is an issue with water flow in your hot tub. If the flashing FLO error code is no longer there, your filters are clogged. They either need to be chemically cleaned over-night in filter cleaning solution or replaced if they are 1 year old or older.
How to troubleshoot a flashing Flo for a spa?
First verify your spa is receiving the specified incoming voltage into the circuit board as well as out of the circuit board to the transformer. Also, check all fuses for continuity. Next, check the service tag on the side of your circulation pump. This will tell you approximately what voltage your circulation pump should be getting.
If you ave one and the jets work, it’s even more likely that it’s a bad pressure switch. Good luck. If the circ pump is buzzing and hot to the touch most likely it is the culprit. If you can remove the equipment access panels, locate the flow switch to see if it is in the closed position or even moving/fluctuating.
Sensor plugged into jack B is not working. SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected.
What to do if your GFCI is flashing Flo?
Make sure there is nothing in the filter area and turn your GFCI back on again. If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter.
What does the flashing light on the intellichlor mean?
EasyTouch has capability to calibrate the water, air and solar sensors. The IntelliChlor self calibrates. If the salt good light is flashing green this does mean the salt level is very hi in the pool. This should be corrected quickly to prevent damage to pool equipment.
