Why are my slide out jacks not working?

Perhaps there is a screen that is clogged. With all the valves and solenoids and wiring it may be possible that one is not operating correctly or perhaps not at all. If there is hydraulic schematic available I could isolate the hydraulic flow of main pressure to the components.

How are the leveling jacks and slide out issues?

When I turn the hydraulic system on I can clearly hear the electric over hydraulic systems engaging, when I set the system to auto level the coach I see all four jacks extend until they each contact the ground however there is insufficient force to lift the coach or to complete a thorough leveling cycle.

What to do when the slide out doesn’t slide?

A stray item wedged in your slide out can be an easy fix, so go check before tearing your motorhome apart looking for the slide motor. You’ll definitely hear the motor laboring if this is the problem, so make sure to keep an ear out for odd sounds too!

Why are there two solenoids for slide out jacks?

A second solenoid for each Jack is unnecessary because the retraction of each Jack is accomplished by the two return springs located on each Jack. that being said,,, the room slide out and generator slide out are both extended and retracted under pressure. There is a separate solenoid for both directions.

Why is the rear stabilizer Jack not working?

At first, a test of the components it was the breaker that was the issue. but now, in order to operate the rear stabilizer I need to manually begin to turn it and then it will operate. I have lubricated the track and that has not made a difference.

What’s the correct level for slide out jacks?

The dipstick is marked with the correct level. Kind of hard to access that area to add fluid. I found pouring the ATF or HWH fluid (HWH fluid is clear, while ATF is red, but either work fine in the HWH system) into a small (8 ounce size works fine) disposable water bottle (yes, clean and dry).

How much pressure do you need for a slide out?

Alpine used HWH systems for both leveling jacks and on most coaches, for slide operation as well ( electric slide mechanism was used on some bedroom slides as well as some generator slides) With You being familiar with hydraulic operation, the common operating pressure for the jack and slide systems is 3000 lbs. when working properly.

Can a HWH slide out be installed on a motor home?

Although HWH has installed slide-outs on Prevost shells, HWH does not install slide-outs on finished motor homes. 24. How do I find a service center or where can I buy your product?

Can a slide out be operated with a rocker switch?

• Most slide-outs are operated with this key panel. • Panel will work with the single-cylinder or multi-cylinder mechanisms. • Some vehicle manufacturers use their own switch or switch panel. • Key controls power to the rocker switch. • Rocker switch extends or retracts the room.

What are the features of straight acting Jacks?

Features of Straight-Acting Jacks: 1. You can not roll off the jacks (but don’t try to drive off). 2. Give a little better stability especially for slide-outs. b. Features for Kick-Down Jacks: 1. If you accidentally drive off the jacks it is unlikely there will be any damage. 2.

Do you have to replace a HWH leveling jack?

Also, HWH systems have assemblies that normally do not have to be replaced as a complete assembly, for example one of the straight-acting leveling jacks is leaking. The complete jack does not have to be replaced; only the cylinder needs to be replaced or repaired.

What happens if a hydraulic jack is unscrewed?

If this release valve is unscrewed, the ball releases the passage and the hydraulic oil is pushed back into the reservoir under the force of gravity of the ram. In order to protect the jack from damage in the event of overload, the release valve is designed as a safety valve and is usually provided with a spring.

How does a hydraulic bottle jack system work?

The figure below shows the simplified design of a hydraulic bottle jack, which shows the principle of operation. The hydraulic fluid is in a closed system. The hydraulic fluid is in a closed system. The housing in which the fluid is confined is provided with two pistons.

What causes a hydraulic slideout to stop working?

Overview A common problem with hydraulic slideouts is that when the switch is pressed to extend or retract the slide, movement starts, then stops, then starts, then stops. There may be a few seconds

What causes a hydraulic system to not work?

Another symptom is that the jacks or slides just don’t operate at all. The system appears to be fine. All the lights are normal, but just don’t DO anything. While not always the case, the culprit is usually a 50 Amp thermal breaker.

What should I do if my electric trailer jack is not working?

If the motor works with that ground wire, then your motor is good and your ground is bad. If your motor does not work, the motor will need replaced. I would definitely check both the in-line fuse and your ground connections, as those are probably the next most likely culprits after you’ve verified the battery is in good shape.

What causes an RV slide out to not work?

A faulty motor or gearbox could be the problem if your RV slide-out gear system is motor-driven. In such cases, if the motor is faulty or breaks down, then the mechanism will not work. If the motor-driven gearbox system is faulty, for whatever reason, your RV slide-out will not work. Your RV slide may experience resistance as it moves in and out.

Is there an electrical problem with the slide out?

Finding an apparent electrical button, the control panel was removed and the wires for the stuck slide were placed on another slide “in/out” button. Again, there was no power to the stuck slide when the “In” was pushed. The two young mobile repair techs were now perplexed and did not have the skill to trouble-shoot the electrical issue.

Why are the jacks on my RV not working?

One particular user who emailed in about this issue said they had cleaned and oil their hydraulic system, but the growling problem still persisted. Growling typically means there’s corrosion somewhere in your hydraulic system, likely in the shafts, and each manufacturer has its own recommendations for troubleshooting this issue.

What to do if your slide out is not working?

But if the pump is running and your slide out is not moving in, then there maybe a problem at your retract valve. If it is broken or damaged, just unscrew it and replace it with a new one. Also, check your wiring to make sure there are no loose connections or broken wires and connections.

Why are the jacks on my RV not extending?

You’ll learn what to do to safely inspect your fluid reservoir and valves, and discover the most common reason RV jacks won’t extend. With Dave’s help, you’ll have your slide room fixed up in no time!

Why does my slide not retract after new motor?

After the new motor was installed, the slide still would not retract. The “square rods” connected to the motor were detached to assure the new motor was functioning. We found that power to the motor existed only when the “out” part of the slide’s in/out button was pushed. There was no power to the motor when the “in” side of the button was pushed.

What happens if you push the slide out button?

If you push your slide-out button and nothing happens, double check to make sure that the path of the slide out is unobstructed. A stray item wedged in your slide out can be an easy fix, so go check before tearing your motorhome apart looking for the slide motor.

Why is my slide out not working in my camper?

If you don’t have enough power coming in, you could start overworking your slideout’s motor until it overheats. This is how you will end up being stuck with an open slideout. Now, let’s get into details! So, you found a perfect parking space for your camper and ready to pull your slide out.

What causes a slide out not to work?

It may even turn out that the problem was caused by faulty wiring or a weak battery, rather than with the slide out itself. Slide outs are typically electric or hydraulic, with each type having their own pros and cons. Electric motor powered slide outs are most often found on smaller slides.

What to do if your slide out gets stuck?

If your slide out gets stuck and has problems extending or retracting, there are some straightforward ways to determine the problem. First make sure the slide out isn’t locked in position, then determine if there is a power supply problem.