Which pool valves should be open?
These are “3-way” style valves. From left to right, they are SPA MAIN DRAIN, CLEANER, SKIMMER, and POOL MAIN DRAIN. For the cleaner to operate at maximum efficiency, only the skimmer and cleaner valves should be open. No other valves should be open.
How does a spa check valve work?
A check valve in easy terms is a valve that allows water to only go one way/direction. So if you have a raised spa water can only go TO the spa and when the pump turns off the valve shuts not allowing the water to go backwards inside your plumbing allowing the water level in the spa stay put.
Where should a spa check valve be installed?
As such, a common location for a check valve is on the incoming suction pipe, in front of the filter pump. For best results with pump priming, especially for pumps lifting more than 24” from the water surface, the check valve should not be installed directly against the pump intake, but 12”-18” in front of the pump.
What is a spa make up valve?
The “Spa Make-up” valve in that diagram causes the spa spillover to run at a low flow rate any time the pump is on. This is optional, but very handy when you don’t have automation, as you don’t want to leave the spa too long without circulation.
How does a spa drain valve work in a pool?
SPA DRAIN – Valve 1 is rotated half way to allow water to flow from both the Pool and the Spa. This allows water to drain from the Spa. Valve 2 is rotated all the way clockwise to shut off water to the SPA so that it can drain without new water reflilling it.
How does a pool Valve actuator work in Spa mode?
The Actuators on top of valve 1 is commanded to turn with the handle all the way counter-clockwise to shut off the water FROM the SPA. Simultaneously, Valve 2 on the return side is commanded to rotate the handle all the way counter-clockwise to shut off water going TO the SPA. SPA MODE – In this mode, all water flows to and from the Spa.
Where are the valves on a pool pump?
On the right side, three manual valves control the flow from the Pool sources – the Pool Main Drain, two Skimmers and a Cleaner Port (not labeled). An automatic Diverter Valve (labeled “1”) was installed to control flow from these Pool sources or the Spa Drain and feed that back to the Pump.
What does a check valve on a pool do?
Please try again later. The function of the Check Valve is to stop water from doing what it naturally does when the pool turns off, which is to flow in the direction of least resistance which is back down the pipe into the pool.
When to install a check valve in your pool plumbing?
The check valve should be installed in the pipe leading up to the solar panels. SPA – The level water in your spa is often higher than the water level in your pool. When water to the spa is shut off, the spa water level would drain to the level of the pool water. A check valve is installed to maintain the level of the spa water.
How to set up pool Diverter Valves for spa?
By rotating Valves 4 and 5 fully clockwise, water flows through Valve 4 to Valves 5 and 6. Valve 6 supplies water to the lion heads and Valve 5 supplies water to the spa fountain. Water to the spa jets and the pool returns is blocked off. FOUNTAIN HIGHER – To increase the height of the fountain from the above setting. rotate Valve 6 45° clockwise.
How to turn on a hot tub / spa with the valves?
The last thing to remember is after going into your spa turn your valves back to where they were prior to turning on your spa/hot tub. 100% spa suction off and 80% pool to 20% spa return side. If you can imagine what the pump is doing and taking water from it is very easy for you, the homeowner, to not get confused by this process!
Why do you need a circulation valve in your pool?
Circulation of water is one of the most important parts of pool maintenance, water sanitation, and for keeping your pool looking and feeling its best. The best place to dive into pool circulation is with pool valves, which manage the movement of water in your pool.
