Which is the best pool heater Jandy or LXI?

Jandy LXi Pool and Spa/Hot Tub Heater Jandy LXi pool and spa/hot tub heaters exceed environmental standards for Low NOx emissions. Lower emissions m…

How does the JXI pool and spa heater work?

VersaFlo Integrated Bypass Technology The JXi™ with VersaFlo is the first and only swimming pool heater that automatically directs the flow of water through the heat exchanger when heat is needed and around the heater when heating is not needed — allowing you to save money on the filtration pump electric bill.**

What is the serial number on a JXI gas pool heater?

* The JXi Revision can be identified by the first letter of the serial number found on the heater rating plate. ** To install on Rev G and Earlier JXi heaters, R0719400 and R0719500 Must Be Replaced together. 15 Gasket Kit Item Number: R0590900 25 Gas Valve Item Number: R0591400 Style is subject to change as manufacturer may change their vendor.

What’s the warranty on a JXI pool pump?

5-Year Heat Exchanger Warranty – JXi heaters with VersaFlo factory installed receive an industry leading 5-Year standard warranty on the heat exchanger. Heat When You Want. Save When You Don’t. – The heater is typically only used 3.5% of average annual pump runtime, the other 96.5% of the time the heat exchanger can be bypassed

Why did my Jandy JXI 400 not start up?

My brand new Jandy Jxi 400 wouldn’t start up the very first time we tried to use it. 1st Jandy says it’s because we don’t have the proper gas feed – 30’ @ 1 1/4” was plenty, but we upgraded to 1 1/2” after waiting 2 weeks for SoCal Gas and my plumber to be available to meet on the same day.

Why does my Jandy pool not fire up?

The Jandy rep came out and we tried to wiggle the wires but could not get the heater to fire up. He checked the gas pressure and noticed that there was a spike in pressure and then it would come down to 9.7. Then the heater fired up . After 3 tries the heater would not fire up.

How do you start a Jandy JXI pool heater?

Reset breaker and allow the RS 12 to power up. Start the heater at it’s control panel. The ignition sequence begins and when fan starts watch the sight glass on the igniter until it turns red indicating that the start sequence is ready to light the heater.

What do you need to know about Jandy pro?

Promise to maintain the highest quality standards in all areas of operation. Promise to use high quality materials and world-class processes to manufacture our products. Promise that your equipment will arrive completely tested in pool environments, inspected, and quality-assured. We stand by our promise.

Where do I get my Jandy pool equipment?

To ensure the best customer service and tracking, register your product. Jandy pool equipment is sold exclusively through a nationwide network of qualified pool professionals with the expertise and ability to help pool owners make the best equipment decisions for their individual pool needs.

Can a LXI heater be used as a heating boiler?

Do not use the heater to maintain pool or spa water temperature below 70°F (21°C). Do not use it as a heating boiler or general service water heater or to heat salt water. Consult your dealer for the appropriate Zodiac products for these applications. In the LXi heater, operation is achieved through use of a special “premix” combustion system.

What to do if your Jandy pool heat pump does not start?

The following provides symptoms and solutions for general troubleshooting problems for Jandy heat pumps. Heat pump will not start, no control board display. Breaker or fuse may be tripped. Reset breaker or check fuse. If heat pump still does not run, call for service.

Why did my Jandy LXI heater shut down?

Jandi LXi400. Heater fires up 3 times for about 15 sec each and then shuts down with FAULT- CHECK IGN CONTROL error. The burner does light, I can see the flames and feel the blower and the heat.

Jandy LXi Pool and Spa/Hot Tub Heater Jandy LXi pool and spa/hot tub heaters exceed environmental standards for Low NOx emissions. Lower emissions m…

What are the installation instructions for a Jandy pool heater?

This manual provides installation and operation instructions for the Jandy Pro Series LXi pool and spa heaters. Read these installation and operation instructions completely before proceeding with the installation. Consult the Jandy Pro Series factory, or local factory representative, with any questions regarding this equipment.

Jandi LXi400. Heater fires up 3 times for about 15 sec each and then shuts down with FAULT- CHECK IGN CONTROL error. The burner does light, I can see the flames and feel the blower and the heat.

Is the LXI gas heater safe to use?

The LXi heater is designed and manufactured to provide many years of safe and reliable service when installed, operated, and maintained according to the information in this manual and the installation codes referred to in later sections.

How old is the Jandy LRZ pool heater?

Hello I have a Jandy LRZ 175,000 btu pool heater which is 9 years old. During heating process the exterior gets really hot including the display/control panel. To the point the digital display does no…

Why did my Jandy pool heater shut down?

Heater fires up 3 times for about 15 sec each and then shuts down with FAULT- CHECK IGN CONTROL error. The burner does light, I can see the flames and feel the blower and the heat. The flame sensor and air flow sensor seem to work as well.

Can a LRZ heater be used in a swimming pool?

The Legacy Model LRZ electronic heater is specifically designed for heating fresh water swimming pools and spas, and with proper installation and care, they will provide years of reliable service. Do not use the heater to maintain pool or spa water temperature below 70°F (21°C).

How often does a pool heater bypass the heat exchanger?

With two modes —Heat Mode and Bypass Mode — you can choose when water is directed through the heat exchanger. Pool heaters are typically used only 3.5% of the average annual pump runtime. The other 96.5% of the time, the heat exchanger can be bypassed so the pump works less — saving electrical energy and up to $350 a year.

Why is my pool heater not turning on?

Solution: If your pool heat pump isn’t receiving the power it needs from the breaker, then it won’t power on at all. But if the heat pump was previously working and no longer turns on, a damaged electrical connection could be the problem.

What should the input be for a pool heater?

To test the heater input set-up, turn all other appliances to pilot, then turn on the pool heater and note the reading from the meter, and compare with install manual. Most nat gas heating btu values are 1020-1050/cuft. So, if your gas company supplies 1050 btu/cuft, and you clock the meter at ~6.35cuft/min, then you have ~400,000/hour input.

Why is my Jandy pool heater not working?

I have a Jandy LXI heater that is not working. When turned on the fan does not start and the panel has a green and red light on solid. The fan is in working order. (I have a second working fan that I …

What does it mean when Jandy says check ignition fault?

Jandy pool heater lxi model says check ignition fault what… Customer Question Jandy pool heater lxi model… Jandy pool heater lxi model says check ignition fault what does this mean ? Submitted:7 years ago. Category: Pool and Spa Show More Show Less Ask Your Own Pool and Spa Question Share this conversation Answered in 1 hour by: 3/29/2014

What should I do if my pool heater is not turned off?

– If rectification is not confirmed power to gas valve shuts off after 7 seconds. – 2 additional tries (3 total) then shut down/lock out. – Turn heater off, then back to pool or spa to reset. If the heater is not turned off it will automatically reset after one hour.

Is there a check IGN control fault on Jandy LXI?

I’m getting a CHECK IGN CONTROL fault on my Jandy LXi. It will turn on and attempt to ignite a few times in 4 minutes, but it’s unable to start. Step 15 – I do not know how to check if the igniter is glowing, so I assumed NO and proceeded w/ the boxed steps.

How can I tell if my pool heater is leaking gas?

You can also jump 24vac to the gas valve to open it to see if you get gas smell. Not hard to do but you must be very careful and only do this for short time. You should smell gas in the exhaust vent. The blower will force air through the system and carry unburned gas out the exhaust. It was very prominent on my heater.

Where can I find the Jandy Pro Series manual?

Consult the Jandy Pro Series factory, or local factory representative, with any questions regarding this equipment. Certain sections of this manual are specific to either United States or Canadian installations, and are labeled as such.

Which is the best gas heater for a pool?

Reap the benefits of a gas heater along with additional energy savings of up to 20% with the Jandy JXi™ Pool and Spa Heater with VersaFlo™ – the world’s first gas heater with Integrated Bypass technology. This innovative technology allows you to heat your pool or spa when you want to use them and save when you don’t.

What are the installation instructions for a Zodiac pool heater?

This manual provides installation and operation instructions for the Zodiac Jandy LXi pool and spa heaters. Read these installation and operation instruc- tions completely before proceeding with the installa- tion. Consult the Zodiac factory, or local factory repre- sentative, with any questions regarding this equipment.

What kind of pool heater does Jandy use?

Bring the future of heating comfort to your pool or spa today. Jandy Build the perfect pool environment with Jandy professional-grade swimming pool equipment.

What do you need for a Jandy pool pump?

With a full line of pumps, filters, heaters, lights, valves, water sanitizers, and the automation solutions to control it all, Jandy has the complete equipment package for any swimming pool or spa. Sign Up Today

What kind of power does a LXI pool heater use?

The LXi heater gets electrical power from an external 120VAC or 240VAC source and provides a dual electronic thermostat control system for pool/spa combinations or preheat convenience.

How does the zodiac LXI pool heater work?

Built-in one-touch automation makes pool-to-spa switching simple. The LXi heaters enable easy connection to Zodiac controls, and other pool/spa automation systems and automatic valve systems. Smallest equipment pad footprint. Communicates with the AquaLink RS family of controls. Fan assisted low NOx combustion. .

How to check the ignition of a pool heater?

Wondering if it’s the ignition control or the Main board. 1. 120 VAC to Igniter – Igniter heats to 2600 °F. – 40 second heat-up. 2. 24 V is sent on the Brown wire to Gas Valve Gas Valve Opens.

Is the JXI pool heater an internal combustion chamber?

The Jandy Pro Series JXi pool/spa heater is a blower assisted, internal combustion chamber, residential heater. General All gas fired appliances require correct installation to assure safe operation.

Who is the service technician for the Jandy pool heater?

BillyHvac Journeyman Service Technician/Inspector State Licensed Mechanical Contractor 15,836 satisfied customers my pool is in freeze protection mode. cannot get the LXI heater

What did I do to my Jandy pool heater?

So I opened up our Jandy Legacy LRZ 399,000 to replace the insulation panels. While doing so I disconnected the unit to make examining the heat exchange easier. Once done trying to turn on the heat threw FAULT-CHECK IGN CONTROL.

What is the range of a pool heater?

According to the spec 5.5 to 10 is the range. He mentioned it short cycled, which is what I’ve noticed in the past. It heat the element , maybe 5 10 seconds later you can hear the gas supply switch turn on . The sound of flames igniting occurs and instantly the gas supply switch turns off.

How big is the Jandy LXI pool heater?

Built-in one-touch automation makes pool-to-spa switching simple. Enables easy connection to Zodiac controls, and other pool/spa automation systems and automatic valve systems. Available in 250K and 400K BTU sizes.

Is the water temp sensor independent of the heater?

The water temperature on an automated control system is a sensor which is independent from the one installed in the heater. When these are working they are fantastic for the owners. However when problems arise, it can cause a lot of stress and unanswered questions.

Where is the temperature sensor on the l700c spa?

If feeling unsure of the installation, a little silicone can be used to seal the opening. Since the quantity of silicone required is not much, clear silicone would be sufficient. Since the heater does not shut down at the set temperature, where is the temperature sensor located on the L700C spa?

Are there any problems with the pool temp sensor?

However stated above are only a few pool temp sensor problems. There may be other temp sensor problems which require answers and solutions. If wondering how to resolve the issue one may be facing with a temp sensor, Experts can be contacted for information or guidance.

How to troubleshoot Jandy LX or LT low pressure thermostat?

Fireman’s Switch Water Pressure Switch Hi Limit 150° F Hi Limit 135° F Fusible Link Exhaust Limit Temp Switch Air Pressure Switch Transformer Hot Surface Igniter Flame Proving Rod Fuse Low Pressure Hi Lim Sw Ext Sw 1 Air Flo Sw AGS 10 K Ohms Thermistor Temp Sensor MV MV Ground Low Pressure Thermostat (LX = GUI or LT = T-Stat) IG N 2 4 0 L1 TH VA

How to troubleshoot a Jandy water pressure switch?

JANDY LX or LT LOW NOx TROUBLESHOOTING Fireman’s Switch Water Pressure Switch Hi Limit 150° F Hi Limit 135° F Fusible Link Exhaust Limit Temp Switch Air Pressure Switch Transformer Hot Surface Igniter Flame Proving Rod Fuse Low Pressure Hi Lim Sw Ext Sw 1 Air Flo Sw AGS 10 K Ohms Thermistor Temp Sensor MV MV Ground Low Pressure Thermostat

Do you need to replace the transformer on Jandy LX?

(115 / 230 VAC) Make certain correct conversion block is installed. Replace transformer. Check in-coming power. (115 / 230 VAC) Make certain correct conversion block is installed. Replace transformer. NO

What does a Jandy hot surface igniter do?

Jandy Hot Surface Igniter for Jandy LXi Heater In your pool heater, the igniter plays an essential function in providing heat, and ensuring that you heater is running safely when it is in function. Each and every Jandy and Zodiac heater has a unique igniter that works with other internal components to provide safe and efficient heating.

Who owns Jandy pool products?

As of September 27, 2007, Jandy Pool Products, Inc. was acquired by Zodiac Marine Holding SAS.

What is the best gas pool heater?

The Hayward Universal H-Series H200 is the best gas pool heater because of its ease of use and flexibility.

What is the best heater for an inground pool?

Natural Gas is the most popular pool heater. This is the most widely used type of pool heater and is considered the best option. They heat up a pool relatively fast regardless of the air temperature. They are, however, expensive to operate and may not be as fuel efficient as other heating options.

What are the different types of pool heaters?

There are three basic types of swimming pool heaters: gas heaters, electric heat pumps, and solar-based heaters. Each type has its advantages and disadvantages. Gas heaters run on propane or natural gas, and thus require a propane tank, or a natural gas hookup.

How long does it take to fix a Jandy LXI gas heater?

Hello , There was no answer in this thread for more than 60 days. It can take a long time to get an up-to-date response or contact with relevant users. 400K BTU Gas Heater Rebuild or Replace?

What can Jandy Aqualink RS systems do for You?

Premium Automation at its Finest Jandy AquaLink RS systems enable total control of your backyard experience. AquaLink RS systems are fully integratabl… See it in action! Control individual pool and spa functions, lighting, and water features from the convenience of your home

What do you need to know about Jandy pool control?

Control individual pool and spa functions, lighting, and water features from the convenience of your home Automate daily pool equipment functions, such as filtration, sanitation, and cleaning and create one-touch macros Love the automation at my finger tips. Easy to use and understand. Love total control and this system delivers.

Is the Jandy Aqualink Rs pool control system wired or wireless?

About AquaLink RS Home Automation: Now you can integrate Jandy’s AquaLink RS pool/spa control system into your whole home network. Installation of the Jandy AquaLink RS wireless system is simple and takes half the time of a wired system. Ideal for homes with existing decks and landscaping.

What makes a Jandy pool heater so good?

Providing industry-leading engineering, Jandy’s innovative line of pool heaters and heat pumps are designed to deliver quality, energy-efficient heating solutions so you can enjoy a longer swim season in your pool. The perfect pool is neither too hot nor too cold.

What does high limit mean on Jandy pool heater?

The high limit would be the right most limit. I am getting the high limit error on my Jandy LXi heater. I bought the replacement harness with switches for the Jandy Lxi. My thought was to shut off power to my heater and pump filter and then replace the harness.

Why does my LXI heater say high limit?

This week when trying our Lxi heater out (it is about a year old) I got a fault message of “High Limit” and the burners did not fire. I have done some research and believe I know where the limit switch is located, how to test it, and how to replace.

What kind of combustion system does a LXI heater use?

In the LXi heater, operation is achieved through use of a special “premix” combustion system. The operation of this type of system is affected by fuel gas properties. As noted in the troubleshooting and main- tenance sections of this manual, adjustments may be necessary if the local gas supply is of especially high or low heat content.

What’s the warning on the Jandy pro Rev T?

Jandy Pro Series H0286900 Rev T EGLISH WARNINGIf these instructions are not followed exactly, a fire or explosion may result, causing property damage, personal injury, or death.

Is the Jandy LXI pool heater good for the environment?

Jandy LXi heaters exceed environmental standards for Low NOx emissions. Lower emissions mean you can enjoy your pool with confidence, knowing your pool equipment is designed with the environment in mind. High efficiency C-Fin heat exchanger is designed to lower operating costs and provide greater savings.

What makes the zodiac Jandy LXI lxi400n so good?

Low NOx, fan-assisted combustion and Hot Surface Ignition systems provide maximum performance in all weather conditions. The feature rich control panel has a user-friendly backlit display and a simplified menu for ease of operation. Built-in one-touch automation makes pool-to-spa switching simple.

What are the features of the zodiac LXI LXI?

Highlights include much quieter operation than the previous LAARS LX model this is based upon. Includes the remote thermostat or the remote Off/Pool/Spa switch without having to purchase anything extra. Will fire up to prevent freezing when water temperature is a (settable) 36~40 degrees.

Is there a warranty on Jandy pool equipment?

Jandy pool equipment is sold exclusively through a nationwide network of qualified pool professionals with the expertise and ability to help pool owners make the best equipment decisions for their individual pool needs. Therefore, we do not provide a Manufacturer’s Warranty on Jandy equipment purchased online through any internet retailer.

Is the Laars LX LT a standing burner?

The Laars LX and LT have no standing pilot burner. They exceed the requirements of energy conservation regulations such as those in California, Hawaii, New York, Oregon and other states which require that a pool heater not have a continuous ignition source.

What is the ANSI standard for a Laars pool heater?

The Laars LX and LT are certified by International Approval Services, Inc. to comply with latest editions of applicable U.S./Canadian combined standard for gas-fired pool heaters. In the United States, the applicable standard is ANSI Standard Z21.56 for gas-fired pool heaters. In Canada, it is Standard CSA 4.7.

Is the Laars LX LT manual-royalswimmingpools?

Laars LX LT Manual – RoyalSwimmingPools FOR YOUR SAFETY – This product must be installed and serviced by authorized personnel, qualified in pool/spa heater installation. Improper installation and/or operation can create carbon monoxide gas and flue gases which can cause serious injury, property damage, or death.