Where to find support base for Sweetwater hot tub?
Read and carefully follow the requirements for your hot tub’s support base (found in the section titled, “Locating Your Sweetwater Hot Tub”, page 8).
Why is the FL1 code flashing on my Sundance spa?
the TB1 terminal block and then power up the spa. If the pump doesn’t run you could have a bad pump. I have a 2004 Sundance Lagunas Spa that also has the Fl1 error code. I have had them in the past, and was able to reset it with the hose up to the intake trick on many occasions, but not this time.
Is the Sweetwater hot tub covered by warranty?
Damage caused by exposing the hot tub to this abuse is not covered by warranty. We recommend that you always keep the hot tub full of water when it is exposed to direct sunlight and that you keep the Sweetwater insulating cover in place at all times when the hot tub is not in use.
What to do if your spa has FL1 MSG?
Jamie try running the spa without a filter for a short period ie 10min. If the FL1 msg does not go away and you have good water movement from your Jet 1 pump on speed 1 you would want to check your connection from the PWA to the psi switch. If the connection is good you would want to check your psi switch for blockage.
Read and carefully follow the requirements for your hot tub’s support base (found in the section titled, “Locating Your Sweetwater Hot Tub”, page 8).
Why is my Sundance spa not flashing FL1?
If this does not correct the flashing FL1 msg you could have a blockage in the circulation line or at the flow or psi switch or you could have a bad connection at the flow or psi switch or a bad flow or psi switch. If all else fails contact our Service Support Desk to book a diagnostic and repair of your Sundance Spa.
Damage caused by exposing the hot tub to this abuse is not covered by warranty. We recommend that you always keep the hot tub full of water when it is exposed to direct sunlight and that you keep the Sweetwater insulating cover in place at all times when the hot tub is not in use.
Jamie try running the spa without a filter for a short period ie 10min. If the FL1 msg does not go away and you have good water movement from your Jet 1 pump on speed 1 you would want to check your connection from the PWA to the psi switch. If the connection is good you would want to check your psi switch for blockage.
What is the National Electrical Code for Sweetwater?
7)ELECTRICAL SUPPLY:The electrical supply for this product must include a suitably rated switch or circuit breaker to open all ungrounded supply conductors to comply with section 422-20 of the National Electrical Code, ANSI/NFPA 70.
How long does a Sweetwater hot tub last?
Your Sweetwater hot tub is constructed to the highest stan- dards and is capable of providing many years of trouble-free use.
What kind of error does Sundance certa 780 have?
My Sundance Certa 780 Series hot tub is showing an error of FL1. I went through the manual diagnostics and the error is still there. I contacted Aquatech and they suggested I clean the filter with the FilterBrite.
Your Sweetwater hot tub is constructed to the highest stan- dards and is capable of providing many years of trouble-free use.
7)ELECTRICAL SUPPLY:The electrical supply for this product must include a suitably rated switch or circuit breaker to open all ungrounded supply conductors to comply with section 422-20 of the National Electrical Code, ANSI/NFPA 70.
What causes Flo error message on Sundance Altamar spa?
I have a Sundance Altamar spa, and I’ve occasionally had that FLO error message too in the past. If I recall it might have been caused by air in the lines (not filling tub properly?) or possibly from obstruction. I had one of the small cotton intake covers get sucked into pipes before.
Which is Sweetwater Spa offers the best hot tub?
Sweetwater Spas constantly strives to offer the finest hot tub available, therefore modifications and enhancements may be made which affect the specifications, illustrations and/or instructions contained herein. FCC Notice
What should the temperature of spa water be?
Spa water heats at a rate of 3 degrees an hour wired at 110 volts and 10 degrees an hour at 220 volts. If you did not get a reading at all then continue with next test. Make sure that the heater/filter cycle is on, and the thermostat is turned all the way up doing this test.
