Where is the electrical switch on a suburban sw6de hot water heater?

The other morning while breaking camp to head out to the next destination I noticed the electrical on/off switch for my Suburban SW6DE Water Heater was a little stiff and it required a lot of force to turn it off. It is a little rocker switch located inside the external access panel at the bottom left-hand corner.

How does a suburban combo water heater work?

Of course, as part of troubleshooting, we took to learning a bit more about how these components work. Electric Heating Mode – Suburban Combo Water Heater (SW6DE) The electric heating mode on this water heater works off the 110V electric system, i.e. it is powered when the RV is plugged in.

Where is the hot water heater on a RV?

An On/Off switch that is accessed inside the WH panel on the outside of the RV. This powers the electric heating mode. It is OK to leave this in the ON position permanently AS LONG AS THERE IS WATER IN THE HOT WATER TANK… and I’ll show you why in a bit

How can I tell if there is water in my suburban water heater?

On the Suburban, with the cover off, you’ll find the secondary switch in the bottom left corner. How Can I Tell If There’s Water in the Water Heater? First, check that the Water Heater Bypass is in the normal operating position. On many trailers, there is a diagram on the basement storage door showing normal and bypass settings.

How many amps does a suburban sw6de hot water heater use?

It was rated at 125 volts @ 20 Amps, more than adequate for the 10 amp current drawn by the Suburban SW6DE Hot Water Heater element. Out of curiosity, I broke open the old switch to see exactly what happened. I discovered a plastic pivot piece had melted and caused the issue. Where did the heat come from?

Where can I get a suburban water heater installed?

ALL TECHNICAL AND WARRANTY QUESTIONS SHOULD BE DIRECTED TO THE COMPANY LISTED ON THE WARRANTY OR RATING PLATE WHICH CAME WITH YOUR WATER HEATER. 676 Broadway Street | Dayton, TN 37321 USA 423.775.2131 | FOR INSTALLATION IN RECREATIONAL VEHICLES AND MOBILE HOUSING

How do you turn on a 110V water heater?

The secondary 110V switch is a rocker-type that can be pinned in the OFF position with a small cotter pin. On a new trailer, to turn it on the first time, you have to remove the cotter pin and rock the switch to the ON position. You can leave the switch ON permanently.

Where is the switch on the hot water heater?

It is a little rocker switch located inside the external access panel at the bottom left-hand corner. I flipped it on and off a few times and it loosened up so didn’t think much of it.

How big is a suburban 6 gallon water heater?

1 Suburban 6 Gallon Water Heater SW6D 2 Suburban 6 Gallon Water Heater SW6D S/D 3 Suburban Water Heater, 6 Gallon SW6DE 4 Suburban Water Heater, 6 Gallon SW6DE S/D 5 Suburban Direct Spark & Electric Water Heater, 10 Gal. 6 Suburban Direct Spark & Electric Water Heater, 10 Gal. 7 Suburban Direct Spark & Electric Water Heater 12 Gal

Can a DSi water heater be used in a RV?

Select electronically controlled water heaters are perfect for adverse weather conditions with its direct spark ignition (DSI) featuring a remote switch which can be used to conveniently light the water heater from inside your camper/RV!

How to change electric heater in suburban sw6de?

Was easier to slide in and out than old unit that we had to remove. Had to break off most of the foam insulation on old unit to remove. Had one extra orange wire left unconnected with new unit which requires you to use switch at heater itself to turn electric on and off for electric heating feature.

Is there a faulty switch on a suburban water heater?

Adding Inside Switch To Suburban Water Heater Forest River Forums Faulty Electrical Switch On A Suburban Sw6de Hot Water Heater Tale Of Whoah Suburban Water Heater Repair Report Irv2 Forums Will The Atwood Double Panel On Off Switch Work A Suburban Water Heater Etrailer Com Good Sam Club Open Roads Forum Suburban 6 Gallon Water Heater Issue

Is the suburban sw6de 6 gallon DSi DSi electric?

Our previous Suburban SW6DE lasted almost 10 years and had an unbelievably fast recovery rate. This one is the same model… slipped right in… all the plumbing and gas lines hooked right up, no hassle and no leaks. Overall an easy hook up.

How to troubleshoot and repair a suburban water heater?

Water Heater Troubleshooting & Repair (Suburban) This guide is based on the Suburban Water Heater commonly found in most Heartland RVs. Troubleshooting Electric Mode Electric Switches Main 110V Power Switch The main 110V switch is operated just like a light switch and most will illuminate when power flows through the switch.

Why does my RV water heater not start?

To detect whether it is the air causing the problem, light the stove burners, and consequently switch on the RV water heater. In case, the hot heater starts, you could conclude that air entrance is causing the real issue.

What to do when your water heater is not heating?

If both power switches are ON, but the electric element is not heating the water, press both reset buttons on the back of the water heater. If pressing the reset buttons restores operation, it’s an indicator that the thermostat may have failed to cut power to the heating element.

Why is MY Suburban RV hot water heater not working?

Suburban is a brand that always delivers quality products, such as its line of RV water heaters. In the end, it all machinery, and is likely to wary out with time or owing to an internal malfunction. Read on to what could have gone wrong and the corresponding Suburban RV hot water heater troubleshooting.

What should I know about my suburban water heater?

Water Heater Troubleshooting & Repair (Suburban) This guide is intended to assist Heartland Owners in troubleshooting and repairing common failures of the Suburban Water Heater. This document doesn’t specifically cover the Atwood design.

What to do when your water heater wont turn on?

, open a faucet and check that water flows equally when the faucet is full to Cold and full to Hot settings. CAUTION While you’re checking things, make sure if you have an outside shower that the faucets are turned off. If you leave them open, hot and cold water will mix and you will get lukewarm water from other faucets.

What happens when your water heater is in bypass mode?

In bypass mode, with an empty water heater, the cold water supply will flow through both the hot and cold lines. If not certain whether in water heater bypass mode, carefully open the temperature / pressure relief valve. With city water flowing, or the pump pumping water, when the water heater is full, water will come out of the relief valve.

How big is a sw6de RV water heater camper?

Model: SW6DE LP Gas and Electric Electric Ignition 12,000 BTU Heat Gas and 1440 Watt Electric Recovery Rate of 10.2 GPH Gas and 6 GPH for Electric 34.3 lbs Empty Weight Cut Out Dimensions: 12.75″ Wide x 12.75″ High x 19 3/16″ Deep.**INCLUDES POLAR WHITE DOOR 6255APW**

Is the suburban RV water heater camper trailer unuseable?

The local RV repair and sales favility had such difficulty with the Suburban company, they gave up after 2 attempts! I tried a second and a third local company for this “derater kit” and no one could get the parts! This water heater produces over 260 ppm of carbon monoxide and it’s now unuseable.

What does red light on water heater switch mean?

If you’re going by the red light on the water heater switch inside the rig, that means the gas flame has failed and the circuit board has timed out trying to relight it. The electric element should still be operating.

How to troubleshoot a suburban RV water heater?

The Suburban water heater is a 12 gallon unit that runs on either propane or electric. When conducting your RV water heater troubleshooting steps for this unit you will want to locate the control panel. Look for the DCI lights on the panel and if they are lit you will need to go outside and push the reset buttons on…

How can I tell if my RV water heater is working?

You will first need to verify there is 12 volt battery power and to make sure the LP is on and supplying unit. You can check the LP system by simply turning on stovetop inside of the unit. When the unit turns on will you will hear a clicking sound. If the unit clicks but there is no flame, it might mean there is a clog or blockage in the system.

What is the reset button on a water heater?

The left-hand button is the electric circuit reset and the right- hand is the LP reset. If both power switches are ON, but the electric element is not heating the water, press both reset buttons on the back of the water heater.

How big is a suburban RV water heater?

However, there are just a few additional steps you will need to complete when troubleshooting. The Suburban water heater is a 12 gallon unit that runs on either propane or electric. When conducting your RV water heater troubleshooting steps for this unit you will want to locate the control panel.

Can You troubleshoot a propane RV water heater?

Which is why when RV water heater troubleshooting you will want to follow similar steps as if you were troubleshooting your home’s water heater. However, there are just a few additional steps you will need to complete when troubleshooting. The Suburban water heater is a 12 gallon unit that runs on either propane or electric.

How does a suburban gas water heater work?

Heated water attacks all metals – and that’s why Suburban® uses porcelain-lined, steel tanks with an anode rod to “absorb” the electrolytic action – just like your water heater at home. **Image May Differ From Actual Product** WARNING: This product can expose you to chemicals, which is known to the State of California to cause cancer.

Do you need rough-in openings for a suburban water heater?

For convenience of installation, rough-in openings for Suburban® water heaters are small and less likely to interfere with RV exterior design. When a Suburban® Advantage™ porcelain-lined tank is properly maintained, tank life may double or triple its three-year limited warranty saving owners the cost of premature replacement.

What are the features of a suburban water heater?

Suburban Direct Spark & Electric Water Heater, 10 Gal. Suburban Heaters w/ Direct Spark Ignition (DSI) & Motor-Aid Hrt. Finally, a feature known as motor-aid heat allows engine heat to warm water via an exchanger making it an efficient green option that results in saving money.

What’s the serial number on a suburban water heater?

Please Note: This kit is only applicable to the SW6D model after serial number 953401118 (essentially 1995 and newer). All Suburban Serial Numbers manufactured after January 1990, will be nine digits. The first two (2) digits signify the year of manufacture.

Can A S / D water heater be relighted?

S/D models are scratched or dented or possibly a combination of both. These function just as good as a new product would except they are discounted since some minor cosmetic damage is present. They are extensively tested to ensure quality. The re-ignitor is used for relighting the pilot in the event it goes out.

What are the digits on a suburban furnace serial number?

All Suburban Serial Numbers manufactured after January 1990, will be nine digits. The first two (2) digits signify the year of manufacture. The next set of digits, indicate the week of the year and the remaining digits are serial numbers.

Where are the wires on a water heater?

The typical 240 volt water heater has a red and black wire located in a junction box at the top of the water heater. The incoming circuit wires and the water heater wires are normally black and red, and are splices or connected together, color to color using red or gray wire nuts.

What kind of wiring is needed for a 240 volt water heater?

In newer installations where there is a 2-wire with ground cable for a 240 volt water heater the white wire is colored with red electrical tape which clearly designates it’s part of the 240 volt circuit. Identifying the circuit wiring with red electrical tape is important and should be applied to existing circuit wiring as needed.

What kind of wire do I need for a 50gal water heater?

Electrical Connections for a 50Gal Water Heater Identify the circuit for the hot water heater and make sure it is turned off. If the incoming electrical circuit has a black, red, white and ground wire then the white or neutral wire is caped off and not connected unless your water heater requires a separate neutral wire.

Do you need a neutral wire for a hot water heater?

Identify the circuit for the hot water heater and make sure it is turned off. If the incoming electrical circuit has a black, red, white and ground wire then the white or neutral wire is caped off and not connected unless your water heater requires a separate neutral wire.

Why is the DSi light on on my suburban water heater?

During electric operation switch light willl go off and DSI light will come on. Unit continues to operate and gas operation is not on. If use is in gas mode when tur … read more Hello. My Suburban hot water heater model#s sw6d-sw6de-sw6dem wont light. I turn on the inside switch it tries but goes to reset.

Why does my Suburban sw6de water heater not stay on?

My Suburban SW6DE DSI Water Heater will not ignite and stay… 1988 Jayco Jay 27′ Class C. Original WH didn’t have 12v DSI, so no existing wires to connect to. I purchased a new Suburban SW6DE water … read more Vocational, Technical or Tra… Vocational, Technical or Tra… Dsi light wont stay on for water heater. Dsi-flt light

Can a suburban 10 gal water heater ignite and stay on?

Vocational, Technical or Tra… My DSI Suburban 10 gal water heater fires up then you canhear the igniter stays on. After a few seconds the burner turns off. Then it repeats to light … read more

How many sw6de water heaters are left in stock?

Only 6 left in stock (more on the way). . Only 12 left in stock (more on the way). . Only 18 left in stock (more on the way). . Only 3 left in stock – order soon. . Only 6 left in stock (more on the way). . Only 8 left in stock – order soon.

How does a 6 gallon gas water heater work?

The Suburban® Direct Spark/Electric 6 Gallon Water Heater has a direct spark “on” switch that when combined with the optional remote wall plate turns on the water heater wherever you install the switch (remote switch sold separately). Love dry camping far away from the hustle and bustle of the city?

Can you leave the water heater on on a new trailer?

On a new trailer, to turn it on the first time, you have to remove the cotter pin and rock the switch to the ON position. You can leave the switch ON permanently. But be aware that when you winterize, the water heater tank will be emptied, and if subsequently, a visitor turns on the inside 110V switch, the element will be ruined.

Can a water heater be replaced if there is no water?

If there’s no water, the heating element will burn out very quickly and will have to be replaced. Of course, even if your trailer is in warranty, burning out the electric element is considered user error, which is not covered by the warranty against manufacturing defects.

What to do if your water heater won’t stay lit?

Thermostatic Control or Gas Valve If your gas water heater doesn’t stay lit, you may have a defective control thermostat. This control is part of the gas valve assembly and normally has a dial that will allow for temperature adjustment and will also have a probe that monitors the water temperature.

What to do if your tankless water heater has no hot water?

No hot water is one of the most common tankless water heater problems. The first things you should check are the electric power, water, and gas supply to the water heater. Check the shut-off valves, as they might be in the closed position.

What to do if your electric water heater is not working?

Re-connect the AC power wires to the water heater element. It does not matter which color wire connects to which screw. Do not over-tighten, one quarter turn past hand tight should suffice. Replace cover to seal electric heater element.

How to troubleshoot and fix RV water heater electrical problem?

This Suburban water heater repair manual is very helpful for troubleshooting the electrical power circuit to diagnose potential problems. Follow the steps it contains for tracing power through the system to locate any short or break that may be causing the element to not heat up. NOTE: Do not “dry fire” the electric water heater element.

Product Description. Suburban 6 Gallon Hot Water Heater. Model: SW6DEL. DimensionsSuburban SW6DEL 6 Gal Combo Gas/Elect DSI RV Camper Water Heater: 12-1Suburban SW6DEL 6 Gal Combo Gas/Elect DSI RV Camper Water Heater1/16″ 12-11/16″ 19-3/16″. Weight: 34 lb.Suburban 6 Gallon Hot Water Heater. Model: SW6-DEL. Dimensions: 12-11/16″ 12-11/16″ 19-3/16″.

What kind of board does a suburban water heater use?

Fits Suburban Water Heaters: SW4D/ SW6D/ SW6DE/ SW6DEL/ SW6DEM/ SW6DM/ SW10D/ SW10DE/ SW10DEL/ SW10DEM/ SW10DM/ SW12D/ SW12DE/ SW12DEL/ SW12DEM/ SW16D/ SW16DE/ SW16DEL/ SW16DEM What other items do customers buy after viewing this item?

Is the suburban 520814 module board defective?

Update: the new board failed in about 7 months. In that 7 months, i might have switched on the water heater only 20 times. These boards seem to be defective. It started taking a long time to light the water heater. Then, it started lighting but would shut off the water heater a few minutes later.

Which is the leading supplier of RV water heaters?

Suburban® is the leading supplier of RV furnaces, water heaters, kitchens, cooktops, and ranges and ovens. At Suburban, they start with performance, design, materials, and style but they don’t stop until the product meets their standard of quality.

What’s the difference between Atwood and suburban water heaters?

Atwood water heaters have just a drain plug while the Suburban water heater’s drain plug is actually an anode rod. Because they are steel tanks the anode rod serves to protect the steel tank from rusting. Because Atwood tanks are aluminum, they do not require an anode rod.

What should I do if my Atwood water heater fails?

This can cause the water heater to fail before its time! The next step is to drain the water heater by removing the drain plug. Atwood water heaters have just a drain plug while the Suburban water heater’s drain plug is actually an anode rod.

Where is the relay box on a sw6de water heater?

Vocational, Technical or Tra… Have new sw6de water heater. It has relay box where + and – Have new sw6de water heater. It has relay box where + and – are located, which original heater does not. Relay also has orange wire. There is … read more Vocational, Technical or Tra…