Where are the slide outs on a Newmar?
Combinational Slide-Out DOO DOO Voice Intellltec LOCATION STOP ADJUSTMENT AOJUSTMENT DEPLETE/DUMP AIR IN COACH SUSPENSION. SHOULDER SHOULDER SO ‘88404 s,’i6-te RIVET HOLD – HEX ‘52757 – 5/16-18 e Sec±lon E —E WITH PLATE Modeli RTS MAR 342 BEARINGS MOUNTING BEARING BEARINGS 133 14 BUSHING MOUNTING FLANGE BEARINGS _SO_SHAFT 450
What was the problem with my Newmar Northern Star?
I have spent the better part of a week off and on dealing with diagnostics to determine what happened to our kitchen slide on our 2005 Newmar Northern Star. After leaving Tucson and arriving in Lordsburg, NM (for a bomb cyclone layover) our kitchen slide would not deploy.
How to troubleshoot a Newmar slideout Control Board?
I tackled the project methodically by first searching for the problem on the internet. Doing this search revealed a troubleshooting guide for our 2005 Newmar’s slideout control boards. This is what I used for my diagnosis. So, I tested as follows: Test – for the correct incoming voltage for the control board.
Why does my Newmar coach not slide out?
The control board also relies on input from the ignition key position, meaning that if the key is in the on position (motor running or not) the controller assumes you are trying to move the coach with the slides extended and will not allow you to move the coach. I don’t know if this feature works yet.
I have spent the better part of a week off and on dealing with diagnostics to determine what happened to our kitchen slide on our 2005 Newmar Northern Star. After leaving Tucson and arriving in Lordsburg, NM (for a bomb cyclone layover) our kitchen slide would not deploy.
The control board also relies on input from the ignition key position, meaning that if the key is in the on position (motor running or not) the controller assumes you are trying to move the coach with the slides extended and will not allow you to move the coach. I don’t know if this feature works yet.
What should I test Newmar slideout controller for?
Doing this search revealed a troubleshooting guide for our 2005 Newmar’s slideout control boards. This is what I used for my diagnosis. So, I tested as follows: Test – for the correct incoming voltage for the control board. I had 12.8 Volts DC present – No issue with the circuit that supplies power to the controller.
Doing this search revealed a troubleshooting guide for our 2005 Newmar’s slideout control boards. This is what I used for my diagnosis. So, I tested as follows: Test – for the correct incoming voltage for the control board. I had 12.8 Volts DC present – No issue with the circuit that supplies power to the controller.
I tackled the project methodically by first searching for the problem on the internet. Doing this search revealed a troubleshooting guide for our 2005 Newmar’s slideout control boards. This is what I used for my diagnosis. So, I tested as follows: Test – for the correct incoming voltage for the control board.
Why is my Newmar slideout not working properly?
By moving the axle and cogs I must have accidentally re-aligned the two halves of the sensor thus allowing the control board to see that the conditions were right to operate the slide briefly. The motor was so loose that there was some lag between when the momentary button was depressed and the drive axle started to move.
When to extend slide out on Newmar Ventana Le?
During our walk-through of our new-to-use Newmar Ventana LE this past Thursday (3/21/19) at National Indoor RV Center in Lewisville, TX, the technician we had said the guidance from Newmar is to extend/retract slide-outs while the coach is at “ride height”.
Where are the cogs on a Newmar slideout?
There is a cog at each slide support rail. The rails support the weight of the slide and provide a track with holes in it to bring the room in or out in conjunction with the momentary switch, motor, axle, and cogs. Pulling myself back inside, I noticed that the axle had play in it. It rotated a bit not much, perhaps 1/8″-3/16″ of an inch.
During our walk-through of our new-to-use Newmar Ventana LE this past Thursday (3/21/19) at National Indoor RV Center in Lewisville, TX, the technician we had said the guidance from Newmar is to extend/retract slide-outs while the coach is at “ride height”.
How big are the slide outs on Newmar motorhomes?
This “procedure” came about a few years ago when Newmar began installing full wall, “flush mount” slide-outs in their 40 foot plus motorhomes.
Why is my Newmar slide out not working?
Check – Insure the slide out wall locking arms are in the released position. This was quite a task as one was visible (the forward lock) and I could see that it was retracted and not holding the room in. But the aft or (rearward lock) was not visible because it was hidden by our refrigerator wall.
When did the new Newmar slide outs come out?
New for motorized product in 2001, a including a voice message warning the way of the room’s movement”. wi ea Front Black @ ROOM. Front O/_H White DRIER’S KSDP. VTDP. DSDP, ATME PASS.
How to use Newmar slide out kitchen slide?
SLIDE- OUT OUT KITCHEN SLIDE— 9 d 16 PNK 12 REDWHT —S O 6 VIO WHT 2—SWlTC OTO ORG HT 2-SWITC 12 ED EL 6 VIO -1 -SWÍTCH Arms Combinational Slide-Out DOO DOO Voice Intellltec LOCATION STOP ADJUSTMENT AOJUSTMENT DEPLETE/DUMP AIR IN COACH SUSPENSION.
Where are the magnetic sensors on a Newmar slide?
There are also supposed to be magnetic position sensors located on the room. The slide is supposed to have two pairs of these sensors. Two on the coach body, and two on the slide. When the coach sensor contacts the slide sensor, a signal is sent to the control board telling the motor that the slide is fully closed and to shut off.
How old is the Newmar motor coach brochure?
Throughout our 50-year, history we’ve made some incredible coaches and major breakthroughs for the RV industry. Explore all of our historical motor coach records here, and download brochures from previous model years.
