Where are the sensors on a Balboa hot tub?

Note: The below images refer to a Toronto Spa for the location of the control system. Placement varies from spa to spa, but in any case it will be located along the same side of the hot tub as the main control panel. Step 3: Locate the heater’s sensor wires and trace them to where they plug into the circuit board (pictures below).

How do you reset the Balboa control panel?

How do you reset the Balboa control panel? Remove the spa cover and allow water to cool. At 107¡F (approximately 41.7¡C), the spa should automatically reset. If spa does not reset, shut off the power to the spa. Standby Mode has been activated by pressing a button combination on the user panel. How do you check a hot tub fuse?

What are the error codes on the Balboa spa?

Balboa Spa Side Error Codes pd Power supply, unit running on battery ba OH Sensors reading 112-118° F. OHH Overheat. Spa has shut down. One sensor OHS Overheat. Spa has shut down. One sensor

How do I Reset my hot tub control panel?

To reset a hot tub heater you need to locate the red reset button which will probably be on the heater in the service bay of the hot tub. All you need to do is to press it to reset it and everything should be good to go.

Where is the reset button on my hot tub?

Remove the spa cover and allow water to cool. At 107¡F (approximately 41.7¡C), the spa should automatically reset. If spa does not reset, shut off the power to the spa. Standby Mode has been activated by pressing a button combination on the user panel. How do you check a hot tub fuse? – Shut off all power to the spa at the breaker and spa pack.

How to reset the sensors in a Balboa bp501 control system?

Step 3: Locate the heater’s sensor wires and trace them to where they plug into the circuit board (pictures below). Step 4: Disconnect the sensor wires from the circuit board.

What to do if your spa has a sensor balance error?

Step 10: Once the spa has been powered up and running for a few minutes, there should be no more sensor balance error codes displayed. If the Sensor Balance Error continues, please contact us at 1- (877)-347-7727 or create a Support Ticket by clicking HERE to inquire about further assistance.

What is the installation manual for a Balboa spa?

End User Warning This Installation Manual is provided solely to aid qualified spa service technicians in installing spas with control systems manufactured by Balboa Water Group. Balboa controls have absolutely no end user serviceable parts.

Where can I find the Balboa BP troubleshooting manual?

42211 C Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group. Balboa’s BP Troubleshooting & Service Manual SPA CONTROL SYSTEMS PANELS60 Hz BP500 BP2000G1 TP900, TP800, TP600, TP400 THIS MANUAL COVERS THE FOLLOWING:

What are the spa panel messages on Balboa?

Common Spa Panel Messages 1 Low Water Level. 2 Blocked Suction Fitting. 3 Blocked Skimmer. 4 Dirty Filter. 5 Too Many Closed Jets. 6 Closed Slice Valve. 7 Heat Related Pump Not Running. 8 Heat Related Pump Not Primed. 9 Contact your Dealer or Service Organization.

Do you need a Balboa spa control system?

Balboa Direct provides cutting edge, reliable, high value control systems that Balboa Water Group has been known for. Whether you are looking to purchase a retrofit kit, a Balboa spa control system, or need replacement parts on your existing spa control system, you can buy with confidences knowing that Balboa has the right system pack for you.

Can you return a hot tub control system?

Check the label on your current spa pack or know your spa make and model/serial number. Electronics are non-returnable items since they cannot be resold as news. When you buy a spa pack from Hot Tub Outpost you always get a brand new, mint control system with manufacturer’s warranty. Contact us if you need assistance.

Do you need a circuit board for a spa?

It is also why spa manufacturers throughout the world continue to rely on us for all of their spa designs. So whether you are building a spa or replacing a circuit board on an older spa model, or need a generic circuit board to retrofit, Balboa is the right solution for you.

Where can I get a new hot tub Control Board?

We have new circuit boards for your hot tub and spa! Get your spa running again with a new control board at a great price. To narrow search results, enter the manufacturer’s name and the circuit board’s part number into the search box above.

What kind of controller do I need for my Balboa hot tub?

The Balboa Spa Controller VS510SZ Kit is configurable. Internal component circuits are setup to work with your existing pumps, blower and ozone, so you don’t have to do any internal wiring. OEM The Balboa Spa Controller VS520SZ Kit is configurable.

What kind of circuit do you need for a hot tub?

Hard-wiring the spa into a ground fault circuit interrupter (GFCI)-protected 220 to 240V, 50- or 60-amp dedicated circuit. Installing a manual disconnect device, often called a spa panel, between your home’s electrical breaker panel and the spa. This guide on how to wire a hot tub will emphasize the steps that show how to install a spa panel.

Is there a retro fit Balboa spa controller?

Complete retro-fit spa controller that comes with Controller, Heater, Touchpad & Cables. Replaces all older Balboa series that have 1 or 2 pumps, or 1 pump & 1 blower. Perfect replacement for the obsolete SCS 501, GS501, SIG10.

Why is my spa button not working on my Balboa?

Cause: There is an “Over Heated Heater” (OHH or HH) Condition. One of the Water Temp Sensors has detected 118°F (47.8°C) In the Heater and Spa Functions are Disabled. You Must Press Any Button to Reset when Water is below 108°F (42.2°C).

Is the Balboa gs501z complete spa control system?

Balboa GS501Z complete spa control sy… Covid-19 Supply Information: In Stock until Sold Out. Due to Covid-19 supply chain delays, once stock is depleted, these will be available on BackOrder only. All Backorders are sent Express Post once items arrive. See here for ETA information.

How to check spa panel messages on Balboa direct?

1. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode. 2. After about 45 Seconds, Check for Error Messages on the Topside Panel Display. If there is No Error Message, Select “No Error Message” Below. If there is Now an Error Message, select Message Other than CrC or CHKSUM FAIL below.

What kind of products does Balboa Spa have?

Whatever your need, Balboa offers a complete line of products: spa and bath pumps, topside control panels, retrofit kits, spa control systems, circuit boards, ozone equipment, lighting, remote electronic controls, and more. Due to the continued loyalty of our customers, Balboa remains the leading global supplier for the water leisure industry.

Are there any end user serviceable parts for Balboa?

Balboa controls have absolutely no end user serviceable parts. Balboa Water Group does not authorize attempts by the spa owner/user to repair or service any Balboa products. Non-qualified users should never open or remove covers, as this will expose dangerous voltage points and other dangerous risks.

What to do if your Balboa hot tub is not working?

Before you call out a Balboa service technician, though, try to do some troubleshooting with your Balboa hot tub parts. Much of what can go wrong with a hot tub is in the pump. Try to identify the problem you are experiencing before attempting to correct a misbehaving part.

What are the different types of Balboa panels?

Balboa Panel and Manual Reference Guide A reference guide showing commonly used Balboa panels, what systems they work with, and their operating manuals. 42018 B May 12, 2011 TP600 TP901 TP Panel Line-up MLM990S ML900 ML700 ML554 ML553 ML Panel Line-up J1 J2 BL LT HT FC OZ Select Jets 1 Jets 2 Blower Light 102º F

What do I need to know about Balboa direct?

1. Make sure the system has the proper incoming voltage. 2. Check for proper wiring inside the system box and look for any loose connections or cut wires. 3. Plug in a new transformer. Why does the panel display “FLO” constantly and nothing works? 1. This is an indication of a pressure switch stuck in the closed position. 2.

How to check water temp on Balboa hot water heater?

Make sure that the water temperature displayed on the topside panel is at least 1 degree below the heater set temperature and set the control to standard mode. 2. Check voltage across the two connections to the heater. Your meter should read either 120 or 240 volts depending on your installation.

How to replace a bulb on a Balboa hot tub?

How do I replace the Topside Bulb Replacement (on Balboa topsides): Another panel problem may be burned out backlighting bulbs. These bulbs can easily be replaced. With the power off, gently pry up the topside control panel with a screwdriver. Next, locate the gray bulb holes in the back of the panel.