When to use Spa when temperature is flashing?
Do not use spa when temperature is flashing or the OH message is displayed. HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational. SESH = Sensor short, nonfunctional.
What does the Oh message on the spa mean?
The spa is at a temperature above 108° . Do not use spa when temperature is flashing or the OH message is displayed. HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected.
What to do when your spa light goes off?
Shut the spa power off, remove the filter and make sure all the jets are open. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.
Why is the blinking light on my spa not working?
Sensor plugged into jack B is not working. SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected.
Do not use spa when temperature is flashing or the OH message is displayed. HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational. SESH = Sensor short, nonfunctional.
Why does my hot tub have a flashing Flo message?
If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter. It’s very important to remember that if you just finished fresh filling your spa then you could also have had an air lock that caused a Flashing FLO message. By removing the filter you just removed the air lock.
What does it mean when spa light is blinking?
SnA = Spa is shut down. Sensor plugged into jack A is not working. Snb = Spa is shut down. Sensor plugged into jack B is not working. SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down.
What does it mean when spa is shut down?
SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected. Could indicate a flow problem. LF = Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours).
When to use the spa and hot tub light?
The low speed pump or circ. pump will operate continuously until the temperature rises above 45° F. OH = Over heat. The spa is at a temperature above 108° . Do not use spa when temperature is flashing or the OH message is displayed.
How to troubleshoot a problem with a Cal spa?
Troubleshooting 1 Message on the control panel. A message on the control panel may indicate a problem. 2 Problems starting up. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. 3 Power and electrical problems. 4 Heat problems 5 Jet problems 6 Water pressure problems
What are the message codes on Cal spa?
Beginning with the 2014 product line, Cal Spa control panels display different message codes. For a description of these message codes, see the owner’s manual. Use the problem message from the “Problem Messages” Column to diagnose problem
What should water temp be to turn off spa?
Spa functioning is then disabled. Once water temperature is below 108°F (42.2°C), the System will then auto reset. Check for high ambient temperatures or extended pump operation.
Beginning with the 2014 product line, Cal Spa control panels display different message codes. For a description of these message codes, see the owner’s manual. Use the problem message from the “Problem Messages” Column to diagnose problem
Troubleshooting 1 Message on the control panel. A message on the control panel may indicate a problem. 2 Problems starting up. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. 3 Power and electrical problems. 4 Heat problems 5 Jet problems 6 Water pressure problems
When did Cal spas start making hot tubs?
Cal Spas was founded in 1979, and they currently offer more than 250 product models. Each of their hot tubs can be customized from a list of thousands of options, and the company places an emphasis on innovative touches and quality workmanship.
SnA = Spa is shut down. Sensor plugged into jack A is not working. Snb = Spa is shut down. Sensor plugged into jack B is not working. SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down.
How do you check the water temp in a spa?
• Check the water temperature with an accurate temperature thermometer. Remove the spa cover and allow the water to cool. Adding cool water may be necessary. Touch any button to reset the system. If the water is still hotter than the set temperature]
If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter. It’s very important to remember that if you just finished fresh filling your spa then you could also have had an air lock that caused a Flashing FLO message. By removing the filter you just removed the air lock.
What does the logo light on a spa mean?
When the spa senses an issue, the diagnostic logo light may turn off, blink, or the colors may flash independently. Specific logo light behaviors alert you to specific problems: A flashing orange light indicates a problem with the temperature sensor. No orange light means that water temperature is outside of 2° F of the set temperature.
Why does my hot tub have a flashing orange light?
A flashing orange light indicates a problem with the temperature sensor. No orange light means that water temperature is outside of 2° F of the set temperature. A flashing gray light indicates that the heater high-limit thermostat has tripped, meaning that the spa water is above an acceptable temperature range or that there is a flow issue.
