When do I Turn on Economy mode on my spa?
Note that the last measured spa temperature displayed is current only when the pump has been running for at least 1 minute. “St” or “Std” will appear on the display momentarily when you switch into Standard Mode. Economy mode heats the spa to the set temperature only during filter cycles.
What does it mean when your Spa is in sleep mode?
“Ec” or “Ecn” will appear solid when the temperature is not current and will alternate with the temperature. Sleep mode heats the spa to within 20 F (11 C) of the set temperature only during filter cycles. “Sl” or “SLP” will appear on the display until mode is changed.
How does the ThermoSpas work in standard mode?
Pressing the ‘Pump 1’ button will change the mode to Standard and display the Economy-in-Standard icon. The spa will automatically revert to Economy mode after one hour (or instantly if you press ‘Mode/Prog’). Sleep Mode heats the spa to within 20° of the temperature set-point, but only during filtration cycles.
How do you set the timer on a caldera spa?
Press and hold down the “Set” button for three seconds until the “F1” or “F2” icon flashes in the display. Press “Light” to select between Filter Cycle 1 or 2. Then select the “Temp Up” or “Temp Down” arrows to choose the length of the filter time preferred.
When to turn on the hot tub screen?
We can access that by pressing 2 on the filter screen, this cycle is usually turned off. If you do need it due to your hot tub or swim spa being used a lot you can turn it on by pressing 2 again. We’ll set this cycle to run from 10:30 p.m. to 11:30 p.m.
Press and hold down the “Set” button for three seconds until the “F1” or “F2” icon flashes in the display. Press “Light” to select between Filter Cycle 1 or 2. Then select the “Temp Up” or “Temp Down” arrows to choose the length of the filter time preferred.
Can a hot tub be left on rest mode?
On hot tubs without a circulation pump, if you want to keep your water at a set temperature make sure to leave it on the ready mode. However, if you’re ok with your water temperature fluctuating slightly you can keep it on the rest mode and it will only heat during established filtration cycles.
Pressing the ‘Pump 1’ button will change the mode to Standard and display the Economy-in-Standard icon. The spa will automatically revert to Economy mode after one hour (or instantly if you press ‘Mode/Prog’). Sleep Mode heats the spa to within 20° of the temperature set-point, but only during filtration cycles.
Why is the power button on my spa not working?
If you do not hear anything when the button is pressed the button may not be working. First cut off the power to the spa, then locate the electrical box inside the spa, it is normally located under the controls.
What to do if your spa does not come on?
Test or replace .3amp fuse next to terminal box where wiring attaches to the spa. If spa will still not come on test power coming to the spa using a voltage meter. If you do not have a voltage meter wait 6 minutes after turning on the power to see if the pump comes on then call support with findings.
What happens to the temperature of a spa?
Spa will only heat during filter period. Temperature will remain close to desired, but it will drop between filter periods. If users can get in a routine, filter period should overlap the usage time by a half hour. This will have spa temperature closest to the desired temperature.
Why are there no bubbles in my spa?
Low water levels will allow the spa to suck in air unnaturally into the filter. This can result in improper flow of water and air in the spa. 6 Open the valves inside the spa. Valves help move air and water through the internal plumbing of the spa. Partially or fully closed valves will restrict bubbles in the spa.
Do you use the same troubleshooting techniques at the spa?
DISCLAIMER: We at the Spa Care Center use the same troubleshooting techniques that have been provided to you and are fully confident that they work. But, when dealing with water and electricity, it always provides a danger that must be respected.
What do you need to know about SPA will not heat?
NOTE: If you have a Printed Circuit Board (PCB) in the main control box please click here for circuit board troubleshooting. The information below is for mechanical control boxes, without circuit boards. “My spa will not heat” is the number one complaint we hear, it accounts for almost every repair that is sent in to Spa Care Center.
What to do if your Bullfrog spa pump is not working?
The wet-end of the pump has a bleed valve—loosen this until all the air escapes and water starts to drip out, or loosen the union on the pump to let the air out until you see water. Do not attempt this while the spa pump is running. If you need help doing this or this does not resolve the problem, please contact your authorized Bullfrog Spa Dealer.
