When did the Aqua logic salt system come out?

When did the Aqua logic salt system come out?

Introduced by Hayward in 2003, the Aqua Logic salt system is a multi-function pool controller used to fully manage your pool/spa system. It can control pumps, valves, lighting, heaters, and chlorination. It was designed to handle the automation and purification needs of swimming pools up to 40,000 gallons and to utilize the T-15 cell.

Is the salt level on the Hayward Aqua plus wrong?

I have a hayward aqua plus controller which is not showing the proper salt levels; however, when I bring a water sample in the pool store – my salt level is correct. The controller is about 2000 PPM off so it is never producing chlorine. I have tried a new salt cell but the same result.

When does Aqua logic P4 show low salt?

My experience, 10 years with an Aqua Logic P4, and currently on my 3rd cell, is that I get low salt when the salt is not low for some time before the cell completely dies. So, yeah, probably new cell time for you. You must log in or register to reply here.

How do I recalibrate my Hayward pro salt sensor?

Hayward Goldline AquaRite Salt Chlorination System stopped making chlorine. Display shows all settings but salt is zero. Cell tested … read more I just installed a new mother board on my Aqua logic PS4. I just installed a new mother board on my Aqua logic PS4.

I have a hayward aqua plus controller which is not showing the proper salt levels; however, when I bring a water sample in the pool store – my salt level is correct. The controller is about 2000 PPM off so it is never producing chlorine. I have tried a new salt cell but the same result.

Introduced by Hayward in 2003, the Aqua Logic salt system is a multi-function pool controller used to fully manage your pool/spa system. It can control pumps, valves, lighting, heaters, and chlorination. It was designed to handle the automation and purification needs of swimming pools up to 40,000 gallons and to utilize the T-15 cell.

Why is the salt level on my Aqua logic so low?

Looked at the control panel For my Hayward Aqua Logic AQL-P-4 shows low salt. I just added a bunch of salt about a month ago and it was working fine.

When do I reset the salt level in my Hayward pool?

Follow these steps ONLY if Salt Chlorination is Enabled. The Average Salt level needs to be reset after initial start up, after a board replacement, following major pool chemistry adjustments, and when a cell is replaced. Press the (+) key to replace the existing average with this new

What do I need for a Pro Logic pool?

Use the chart below to select the Pro Logic Pool/Spa control system you need and related optional features such as salt water system, wireless and wired remotes, pH and chlorine automation.

What does average salt reading on Goldline mean?

When attempting to recalibrate the average salt reading (default reading {2700-3400ppm}) the pump needs to be running. If the pump is not running, the system will show “NO FLOW”, if flashing this is just a warm up process and the unit is waiting for the water to begin moving through the cell to carry the chlorine out to the pool.

How to check the active salt reading on ProLogic?

The active salt readings ~instant salt appears in the Diagnostic Menu. Press the Menu button repeatedly, until the Diagnostic Menu appears. Then press (>) one time. If all zeros or if Chlorinator Off Percentage Met, press ~+ key. IF, after a short countdown delay, the display does not revert to zeros, refer to step 3.

How much salt is in Hayward Pro Logic salt sensor?

I resently purchased and … read more have pro logic automation and chorine system readings shows 1800 ppm salt but when water is tested at Leslies says it is 5000 ppm. How do I calibrate … read more

Use the chart below to select the Pro Logic Pool/Spa control system you need and related optional features such as salt water system, wireless and wired remotes, pH and chlorine automation.

When attempting to recalibrate the average salt reading (default reading {2700-3400ppm}) the pump needs to be running. If the pump is not running, the system will show “NO FLOW”, if flashing this is just a warm up process and the unit is waiting for the water to begin moving through the cell to carry the chlorine out to the pool.

What do you need to know about Aqua logic?

AquaLogic. Introduced by Hayward in 2003, the Aqua Logic salt system is a multi-function pool controller used to fully manage your pool/spa system. It can control pumps, valves, lighting, heaters, and chlorination. It was designed to handle the automation and purification needs of swimming pools up to 40,000 gallons and to utilize the T-15 cell.

Is the AMP limit on Aqua logic salt too high?

In the future, I will turn off my turbocell before adding salt. 2nd: the motherboard has a 20 amp fuse on it. Unfortunately it seems the Amp limit on the relay is 20 amps too. It has been strongly recommended to replace the 20 amp fuse with a 15 Amp fuse to thus protect the relay and the K1 solder point.

How does the Pro Logic work in a pool?

The Pro Logic includes a Sense and Dispense option that tests and controls the pH and chlorine levels. The Pro Logic automatically converts salt into free chlorine which kills bacteria and algae in the pool/spa. The chlorine will revert back to sodium chloride (salt) after killing bacteria.

Why is the salt level in aqua logic too high?

It is common for old cells that are just starting to fail to read low salt, when the salt level is actually fine. Adding salt allows the older cell to continue working for a while longer. By the time the old cell fails, your salt level can be quite high. The new cell will suddenly read the salt level correctly, and show it as being very high.

How to reset Hayward Aqua rite high salt light?

Each cell is equipped with 500 operational hours and requires a manual reset once it expires. To reset the cell, hold down the ‘Diagnostic’ button for 3-5 seconds. The ‘High Salt’ light is exactly what it says There is literally a higher recommended amount of salt in your pool.