What to do when your slideout is not working?
If your slide does not have a means to prevent further movement when the seals are fully engaged, do not continue pushing the button. Many slides have an electrical switch, called a potentiometer, which is a device to prevent excessive slide seal pressure. These devices are adjustable. Proper adjustment is critical.
Why is my slide out motor not working?
RV Slide Motor not Working. The bad news is that one of your slide out motors may have died. The good news is that the failure is due to a faulty wire or connection which caused a short and tripped a breaker. The latter may not be the case if you have 2 motors on your slide out and one is still working.
Why does my Forest River slideout not work?
The slides on some rigs (like Forest River) will not operate with the ignition or engine running. Safety issue. Other rigs are different. A friend in our chapter had this same problem that he fought for several years. His slideout operated with an electric motor driving 2 parallel rack and pinion sets from a single shaft.
Is it OK to operate drivers side slide?
My owner`s manual states that you should NOT operate the slides until the motor home is level to avoid binding and other damage to the slides. Also, I found out the hard way that the drivers side slide has a motor control board that is riveted upside down in the motor compartment.
What happens if you don’t have the Jacks down on a slide?
Everyone knows real men don’t read instructions! If you are already on a level surface, and you do not have your jacks down, the slide if it is big enough will tilt your coach slightly to one side where it wont be level anymore..
Can you extend slideouts without leveling jacks?
Can you extend the slides without your leveling jacks, or can this cause damage, frame/chassis flexing, the slides binding, etc.? If you are already on a level surface, and you do not have your jacks down, the slide if it is big enough will tilt your coach slightly to one side where it wont be level anymore..
Do you use jacks first or slideouts first?
Yes, jacks first is the more common procedure. BUT, some coach makers have theirs designed to deploy slides first. Just follow the recommendation of the coach manufacturer you choose. Yes, I was surprised by Herman’s response. Our Monaco Windsor owners manual indicates slides move in and out at ride height and leveling comes after.
When to put the Jacks down or air level?
For me that means either air level or put the jacks down. The bottom line is the coach needs to be level before extending the slides. Five is correct, the coach needs to be level before extending the slides. This will help in preventing them from binding. I have made is part of setting up to relevel once the slides are out.
Why does my slide not retract after new motor?
After the new motor was installed, the slide still would not retract. The “square rods” connected to the motor were detached to assure the new motor was functioning. We found that power to the motor existed only when the “out” part of the slide’s in/out button was pushed. There was no power to the motor when the “in” side of the button was pushed.
Are there any problems with the slide out on an RV?
Troubleshooting RV Slide Out Problems: One main problem with slide outs is that they may get out of alignment. The good news here is that each slide can be adjusted separately. All you have to do to fix it is take your RV to a dealer and let them make an adjustment.
Is the retract / expand RAM on a slide system positive?
The retract/expand ram (s) on most slide rooms is not affixed positive to the bracket on the slide itself. The nut is generally not pulled tight to the bracket. This is to allow the ram to work up and down in the bracket. There are numerous slide systems.
If your slide does not have a means to prevent further movement when the seals are fully engaged, do not continue pushing the button. Many slides have an electrical switch, called a potentiometer, which is a device to prevent excessive slide seal pressure. These devices are adjustable. Proper adjustment is critical.
After the new motor was installed, the slide still would not retract. The “square rods” connected to the motor were detached to assure the new motor was functioning. We found that power to the motor existed only when the “out” part of the slide’s in/out button was pushed. There was no power to the motor when the “in” side of the button was pushed.
The retract/expand ram (s) on most slide rooms is not affixed positive to the bracket on the slide itself. The nut is generally not pulled tight to the bracket. This is to allow the ram to work up and down in the bracket. There are numerous slide systems.
How to override the slideout system in an RV?
There are two versions of the controller. For version 1, unplug the (6) pin wiring harness from the controller. For version 2, remove one of the motor leads, either the motor I or motor II lead from the controller. 3. Locate the slideout motor. It will be mounted to one of the slideout rails.
Why does my rear slide out not work?
Rear slideout won’t engage. 2007 crossroads cruiser ct32. Rear slideout won’t engage. There is 12v at the motor, when switch engages it drops to zero. Running power to the … read more I have 5 electric slides and one won’t work. The fuses all I have 5 electric slides and one won’t work. The fuses all look fine. … read more
What happens when you push the slide out button on an RV?
If your RV or motorhome doesn’t have the juice, your slide outs aren’t going to budge! If you push your slide-out button and nothing happens, double check to make sure that the path of the slide out is unobstructed.
Is there an electrical problem with the slide out?
Finding an apparent electrical button, the control panel was removed and the wires for the stuck slide were placed on another slide “in/out” button. Again, there was no power to the stuck slide when the “In” was pushed. The two young mobile repair techs were now perplexed and did not have the skill to trouble-shoot the electrical issue.
Troubleshooting RV Slide Out Problems: One main problem with slide outs is that they may get out of alignment. The good news here is that each slide can be adjusted separately. All you have to do to fix it is take your RV to a dealer and let them make an adjustment.
Are there any problems with the slide out?
Most slide out problems are not that difficult to trace and then solve. There will be those that require the help of a professional technician to repair. The key would be to get to know your system and learn when the task is beyond your abilities to handle .
Rear slideout won’t engage. 2007 crossroads cruiser ct32. Rear slideout won’t engage. There is 12v at the motor, when switch engages it drops to zero. Running power to the … read more I have 5 electric slides and one won’t work. The fuses all I have 5 electric slides and one won’t work. The fuses all look fine. … read more
What to do if your slide out gets stuck?
If your slide out gets stuck and has problems extending or retracting, there are some straightforward ways to determine the problem. First make sure the slide out isn’t locked in position, then determine if there is a power supply problem.
