What to do if your Sundance Spa is having trouble shooting?
Very Important: DO NOT measure by placing your probe on L1 or L2 and the other probe on Ground, you will get a 120 Volt reading which is not correct. Continuity Test or Ohms test: Turn off the power to the spa and with your probe set to a continuity check, probe the 2 heater terminals at the same time.
What does a hot tub circuit board do?
Hot tub circuit boards handle all of the spa program modes, monitors the operation of spa equipment, and most importantly, keeps the spa hot and ready to use.
What kind of circulation pump does Sundance Spa use?
Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.
How can I troubleshoot my Spa circuit board?
Check all of the bits on the board for any signs of damage, looking closely also at the wire or cable connection points on the board. Check that all the wire connections are tight, and look for any signs of water damage to the board. Some damage may be only visible on the opposite side of the board.
What to do if your Sundance Spa hot tub is not working?
If condition persists, contact your Sundance Spas dealer or qualified service technician. If the hot tub water is more than -7C cooler than the temperature set point, jets pump #1 and heater will automatically activate to provide freeze protection.
What are the functions of a Sundance Hot Tub?
There are a number of unique functions designed into your Sundance hot tub to protect it from damage and/or to aid in troubleshooting. The indicator light located on the front cabinet panel of the spa is an early detection system that will notify you when the spa needs immediate attention.
Hot tub circuit boards handle all of the spa program modes, monitors the operation of spa equipment, and most importantly, keeps the spa hot and ready to use.
Where is the white light on a Sundance spa?
The indicator light located on the front cabinet panel of the spa is an early detection system that will notify you when the spa needs immediate attention. A solid white light indicates that all operations are normal.
Why is there no power in my hot tub?
Consult an electrician to find the source, if not readily apparent (burnt wires, water, insects or rodent damage, etc.). Some spas and hot tubs have internal fuses, which are meant to blow when voltage spikes occur. These fuses protect your spa equipment, including pumps, blowers and heaters.
Why does my dead Spa have no power?
The greater disappointment is not being able to use the spa at that moment. If you’ve ever found a “dead spa” with no power, no indicator lights, nothing at all – this post is for you. Here, we outline the seven most common reasons that a hot tub has no power.
Can a high limit switch shut down a hot tub?
In some spas, the heater’s high limit switch can cause a complete power shut down. But this is what it’s meant for! The purpose of a high limit switch is to protect spa equipment (and you!) from harm.
Very Important: DO NOT measure by placing your probe on L1 or L2 and the other probe on Ground, you will get a 120 Volt reading which is not correct. Continuity Test or Ohms test: Turn off the power to the spa and with your probe set to a continuity check, probe the 2 heater terminals at the same time.
Consult an electrician to find the source, if not readily apparent (burnt wires, water, insects or rodent damage, etc.). Some spas and hot tubs have internal fuses, which are meant to blow when voltage spikes occur. These fuses protect your spa equipment, including pumps, blowers and heaters.
The greater disappointment is not being able to use the spa at that moment. If you’ve ever found a “dead spa” with no power, no indicator lights, nothing at all – this post is for you. Here, we outline the seven most common reasons that a hot tub has no power.
In some spas, the heater’s high limit switch can cause a complete power shut down. But this is what it’s meant for! The purpose of a high limit switch is to protect spa equipment (and you!) from harm.
Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.
