What to do if your spa pump is not working?

One preventative measure you can take is to try and place your spa pump in an area free from dirt and leaves. Inactive Motor If your motor isn’t working, check to make sure the power switch is on. If it is and it’s still inactive, check for failed relays, burned out wires, or possibly a blown fuse.

When do I need to replace my hot tub pump?

A common problem with older spas is pump failure. We will guide you through spa pump replacement, restoring your hot tub for many years of enjoyment. If your system is more than 2-3 years old, replace the entire pump, not just the motor or wet end. You’ll have fewer headaches in the long run.

How does a spa pump work in a hot tub?

A spa pump is vital piece of equipment for any spa or hot tub. It is responsible for drawing water into the spa’s filtration system where its momentum pushes the water through the filter, heater and spa jets before the water is returned to the spa. A spa pump is comprised of two main components: the motor and the wet end.

When to change the seal on a spa pump?

It’s highly recommended to change out the pump seal when you replace your pump to ensure a tight, leak-free fit. If your water pressure is low, there may be obstructions preventing the impeller from turning. Check and remove any debris to prevent further jamming.

With over 25 years of experience, we’re equipped to help with any spa issues you have or to discuss a new spa. When your spa pump is making noises… This usually happens if you recently drained the spa. Open the lock nut until you hear air hissing, then tighten up again as water begins to leak.

Can You troubleshoot a hot springs pool pump?

Troubleshooting a pump is a no-brainer for many, but if you have any doubts of what to do, then call the professionals here at Hot Springs Pools & Spas! We care about your safety first and deal with spas on a daily basis, so we can identify a problem quicker than a regular handy-man.

When to fill up a hot tub for the first time?

12. 24 to 48 hours after the spa has been operational, check alkalinity and pH with test strips or test kit—adjust accordingly. Do not complete this step until this water is hot and has been in for 24 or more hours. 13. Do Timely Maintenance as directed, and most importantly, ENJOY YOUR SPA!

Is the low speed pump on my hot tub working?

Hot tub topside control is completely blank and buttons are unresponsive. After power is on for about 4 minutes the low speed pump comes on and … read more Journeyman Service Techni…

Why does my spa pump not turn on?

Rick alot of the Balboa paks have a lockout for the pump ie when the water is cool like after a fresh fill the circulation pump will work til the spa heats within a certain range of your set temperature so like 20 degrees within your set temp. That could be the reason why the jet pump won’t turn on.

What to do if your hot tub circulation pump is not working?

Disconnect the plumbing and turn it on very briefly to see if any funny noises are made. Depending on the location of the problem, a replacement of the bearings, motor, entire circulation pump will be required. Pro-Tip: Your spa circulation pump should run with as little noise as possible.

How to know if your sump pump is bad?

Common Signs of Sump Pump Problems 1 The sump basin is filled with water but the pump doesn’t turn on. 2 The performance of the pump is reduced and it removes water slowly. 3 The pump is running non-stop or too often, even if the basin is empty. 4 You can hear loud or strange noises while the system operates. 5 The basin refills quickly.

What to do when your hot tub is not filling up?

One jet may be the ozonator jet and may not appear to be working, this is okay. You can also check the clear tube coming out of the small circulating pump, (at equipment system inside of the cabinet) and going into the heater housing, to see if the water is flowing properly. 7. Run jets for 2-3 minutes with the heat still in the OFF position. 8.

Why does my spa pump make a noise?

When your spa pump is making noises… This usually happens if you recently drained the spa. Open the lock nut until you hear air hissing, then tighten up again as water begins to leak. Cut off your power, close valves on each side of the pump, and remove the wet end cover plate to inspect the impeller.

How to fix a flow problem in a hot tub?

How to fix a hot tub water flow problem 1 Check water level 2 Release any pump airlocks 3 Clean your hot tub filter 4 Check the pressure/flow switch 5 Check the pump is working

When does a hot tub pump have a problem?

And when the spa pump ain’t happy, ain’t nobody happy – that’s because without water flow, there is no filtration, no sanitation and no heating. Spa pumps need to operate every day to maintain clean and hot spa water – so when your hot tub pump has problems, it’s an emergency.

What kind of pump does a hot tub have?

Spas and hot tubs with one pump usually have a 2-speed motor, operating on low speed most of the time, and on high speed when using the tub with the jets. Here’s a simple way to troubleshoot your spa or hot tub pump. Hot Tub Blogs should do this more often – These are our most Frequently Asked Questions about spa pump repair.

Why does the spa pump need to be on high?

They provide the circulation for the spa filter and heater and give an extra boost when turning the spa jets on high. And when the spa pump ain’t happy, ain’t nobody happy – that’s because without water flow, there is no filtration, no sanitation and no heating.

Nicolas try and disconnect your remote panel near the bottom of the Sentry control box. If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance spa. Sundance series 880 spa temperature increase button does not work. All other panel functions work.

Why is the increase button on my spa not working?

If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance spa. Sundance series 880 spa temperature increase button does not work. All other panel functions work. John if the decrease button works and the increase button does not you could have a bad topside control.

What’s the reset button on an old spa?

Older spas used mechanical Temperature and Hi-Limit switches. This type of Hi-Limit can usually be reset by pushing in its reset button, a red or black button located on the heater or equipment pack (see your spa manufacturer’s instruction manual for exact location on your spa).

When to turn off the heater in a spa?

The Hi-Limit shuts off the heater or spa equipment when it detects a water temperature of 109° – 116°. The Hi-Limit on most newer spas can be reset by turning off the spa’s main power supply, and allowing the water to cool to below 100°.

What to do if your spa breaker trip?

Test for pump 1 or circulation pump and heater Turn spa power OFF at the breaker and unplug all the accessories and pumps with the exception of pump one or the circulation pump. Turn spa power ON at the breaker and press the temp button. Either pump 1 will operate at low speed or the circulation pump will come on. Did the breaker trip?

Why is my GFCI breaker tripping my hot tub?

Many people make the mistake of calling their Electrician first and costing them a wasted service call fee. Or they rush out to the Big Box Store and plunk down a hundred bucks for a new GFCI Breaker, only to find out, once installed the new Breaker still trips.

How do you turn off a power breaker on a hot tub?

If you carefully loosen and remove each of the to 3/8″ Nuts, then lift off the strap or Wire, therefore disconnecting the heater from the Circuit Board. Third: Once the heater is disconnected, Turn the power breaker back on.

Why does my water pump not work after I refill the tub?

The pump won’t work if you forget to open those valves before restarting the pump. And check that the jets of the pump are clear. Turning off the pump while you drain and refill the tub may have loosened debris from a deteriorated internal pump part and this may clog the jets.

Do you have to keep refilling your hot tub?

Because your spa takes care of you, it’s only fair that you give it a little TLC in return. It doesn’t take much to maintain your spa on a regular basis —just keep the water clean, and periodically drain it, clean it, and refill it.

What to do if your hot tub is not working?

Answer: Yes. Contact your local spa supply store to check what chemical to use and your local water conditions. Check air valve or clean the air pipe. (Refer to BBF error code checking flow). If still not working, replace the power board or air generator

How long does it take for air to come out of hot tub pump?

So water’s going to come out, some air’s going to come out. And then that pump is going to surge and it will start running again. It might take up to 3-4 minutes. Then once it’s running again, you will have more water, because it’s going to be able to pressure will be coming out.

What does a circulation pump do in a hot tub?

Hot tub circulation pumps are low-flow pumps that constantly circulate in water as slowly as possible to provide your spa a continued filter, heat and chemically treated water.

How long does a hot tub pump last?

While these pumps are known to last 5-10 years, at some point your pump is going to see problems that need some instant attention— unless you enjoy non-chemically treated spawater, which we hope you don’t! Seeing foam in your hot tub could be a sign that your pump is not working correctly.

Is there a pump that has only one speed?

This pump is a 3 hp jet pump that is only a single speed, which normally means there’s another pump somewhere else that runs the water through the heating element, I’ve never seen a spa that only has one speed, and with that pump, the only speed would be high speed all the time.

What does a circulation pump do in a spa?

Circulation pumps are low-flow pumps that constantly circulate in water as slowly as possible to provide your spa a continued filter, heat and chemically treated water.

Why does my Sundance spa not heat up?

It sits 3. I have noticed that that I have a constant FLO error, and the water will NOT heat unless the jets are running. I also believe that my circulation pump is causing these issues. It buzzes and is warm to the touch, but I can’t feel the water moving at all. I just don’t think it is working properly.

What are the functions of the spa pump?

The Spa is recirc and temperature controlling correctly and the pumps are working during the daily auto cycle with an LCD icon on display. The main control panel looks fine (no misting), is backlit, the light buttons work correctly, but no other button functions are working (Temp, Pumps, Programming).

How can I tell if my Sundance Spa is having problems?

The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation. Is there voltage going to pump, Is there adequate Flow coming out of Heater Port in Spa?

What happens when a spa goes into the watchdog?

When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model).

Is there a problem with my caldera hot tub pump?

This doesn’t mean that there’s an issue with the pump; it simply means that you’ll have to rule some things out to get to the root of the actual problem. As always when troubleshooting, have your Owner’s Manual handy. On Caldera Utopia® Series spas, the logo light serves as a helpful and visible diagnostic tool.

What does it mean when your hot tub stops working?

When the GFCI detects an issue with the power supply, such as a ground fault or a short circuit, it cuts off all electricity to your spa. When that happens, it’s called “tripping” the GFCI. To reset the GFCI and restore power to the spa, simply press the GFCI’s reset button.

What to do if your circ pump is not working?

Check that your power is on, the breaker or GFCI test button are not tripped, all valves are in the open position. Follow the circ pump plumbing, and look for any kinks in the hose.

What causes a spa pump to stop working?

Other causes of a non-working pump may be: 1 Pump cycle ended – press the button to turn the pump on. 2 Slice valves closed – open the slice valves. 3 No power – check pump connection in spa control box. 4 Blockage in line – clear obstructions in the filter assemblies.

What does a surging hot tub pump mean?

Surging pumps can indicate the following: Water level is too low – add water according to instructions in your manual. A blockage or restriction – empty the filter basket and clean suction drain covers. 4. Pump (s) Not Priming Priming is an important process that purges air from the plumbing lines of your hot tub.

When do I need to run a spa pump?

Sometimes the topside controls indicate that you need to run pumps to purge air after the tub is full and in use. This priming should take no more than two minutes, by which time water should flow (not surge) from all of the jets (assuming the jets are clean ).