What to do if your master spa pump is not working?
While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump. Run a hot tub temporarily with filters out of the hot tub and see if the problem continues.
What to do if your Master Spa has an error code?
Unplug sensor and switch sensors around. If the problem switches to SnB, then you have a bad sensor. If the problem stays SnA, then you have a bad PC board. Same with the error SnB. Find replacement PC board. Sensors are out of balance. If this alternating with the temp, it may just be a temporary condition.
How often does a Master Spa hot tub filter?
Your hot tub is only scheduled for filter 2 times a day for 2 hours. This may cause your water temp to not be at what you have it set at. The hot tub is in Sleep mode. While in Sleep mode your hot tub will filter 2 times a day for 2 hours a piece. Your hot tub does NOT heat during this time in this mode. The hot tub is in Standby mode.
What kind of control panel does Master Spa have?
The touchscreen control panel is featured on the following Master Spas products Twilight Series Hot Tubs, Michael Phelps Legend Series Hot Tubs, Michael Phelps Signature Swim Spas and most H2X Swim Spas. Although the size and shape of these panels may look different they all operate the same.
What to do if your Master Spa is not working?
While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump. Run a hot tub temporarily with filters out of the hot tub and see if the problem continues. If error message goes away you have dirty filters. If the problem continues make sure circulation pump is moving water.
Your hot tub is only scheduled for filter 2 times a day for 2 hours. This may cause your water temp to not be at what you have it set at. The hot tub is in Sleep mode. While in Sleep mode your hot tub will filter 2 times a day for 2 hours a piece. Your hot tub does NOT heat during this time in this mode. The hot tub is in Standby mode.
Why do I get error messages on my Master Spa hot tub?
In addition to Master Spas hot tub error messages. You may also get a ‘periodic reminder message‘. These are designed to help you remember to undertake proper water care and maintenance.
Why does my Master Spa have two heating modes?
There are also two heating modes, when your unit does have a circulation pump it will always be in ready mode, which allows for on-demand heating so that your water will always be at at set temperature. On hot tubs without a circulation pump, if you want to keep your water at a set temperature make sure to leave it on the ready mode.
What does it mean when your Master Spa says dry?
A substantial difference between the temperature sensors was detected. This could indicate a flow problem. For the error messages of HFL, LF, Dr, or DRY. This means that there is a flow issue through your heater. Try and clean your filters.
What to do if your Master Spa code is not listed?
Below is a list of Master Spa error codes. The code on Master Spa is normally an easy fix, however, if your Master Spa code is not listed, please call customer care 855-308-2149; we do offer limited technical support. No message on display. Power has been cut off to the spa. Check your breaker and turn back on, if off.
Is there a replacement pump for Master Spa?
Get all the parts you need to fully assembly your replacement spa pump. The Master Spas Circ Pump, Top, Center Discharge, 120V G.G./Olympian is specifically designed as a replacement for select models.
How does a circulation pump work in a Master Spa?
Many hot tubs today, however, come with separate circulation pumps to keep water flowing and clean. Most master spas have two different types of pumps, one for hot tub circulation and one for jet power. Jet pumps pull the spa water through a filter and push it back out through the jets.
What are the parts of a Master Spa?
Our Master Spa Legend Series hot tubs are ultra-premium hot tub spas, which look and feel luxurious with high-end parts such as Master Spa Legend Series control panels and high-performance Master Spa Legend Series filters.
What to do when your Master Spa shuts down?
Try unplugging topside and plugging into another port. Check the fuse for topside. Find replacement fuse. “Overheat”- The spa has shut down. On some systems, an alarm will sound. One of the sensors detected 118°F at the heater. Remove spa cover and let the water cool down. After the water has cooled, push any button to reset.
