What to do if your jacuzzi is flashing FL-1 code?

If you have a Jacuzzi and the topside is flashing FL-1 code and the heat is not working ? This is your DIY ( How Fix My Spa VIDEO ) In this video I will show you STEP BY STEP what to look for and check to figure out what is the problem and why the heat is not working along with TIPS on how to get your Jacuzzi heating and running again…

What does FL1 mean on a hot tub?

FL1/FL2. This code means any of the following: the flow switch is malfunctioning open (FL1) or closed (FL2), the filter cartridge needs to be changed or cleaned, or there is an “air lock” condition at the circulation pump intake. The hot tub heater and jets pump will likely deactivate, so now is a great time to call a service tech.

What to do if your jacuzzi heater is not working?

Purge air lock from jet pump 1 by loosening the upper pump head drain screw for a few seconds. Then retighten. 5. If problem persists. Contact your dealer. The pressure switch is malfunctioning or closed. Heater is deactivated. 1. Turn power off to the spa. 2. Check water level. Should be one inch below lowest pillow. Add water if necessary. 3.

Why do I get error message on my Jacuzzi hot tub?

Contact your local dealer or a qualified technician. This error is associated with the UV system. A bulb needs replaced. 1. Press and hold Jet pump 1 + Cooler button together for 3 seconds. 2. The screen will display two menus. 3. If ‘U’ is displayed then press jet pump.

What is the error code on my jacuzzi heater?

If you power the spa back on and these steps don’t correct the error code, it is time to start troubleshooting the circuit board, sensors, and possibly the heater or topside (though not likely). Q:My control panel reads the error code “SN1.”

How to fix jacuzzi brand hot tub error messages?

Press either + or -. This will change the display to = and will disable the countdown timer that creates the original message. Contact your dealer for replacement. Next up are the hot tub error messages for the newer Jacuzzi® series, J-400 and J-500 series. They have a full digital display, which will indicate what is wrong.

How to fix no heat on Jacuzzi in Arizona?

Flashing FL-1 code and no HEAT on Jacuzzi (DIY) Step by Step how to FIX. Arizona Hot Tub Factory Flashing FL-1 code and no HEAT on Jacuzzi (DIY) Step by Step how to FIX. Arizona Hot Tub Factory Flashing FL-1 code and no HEAT on Jacuzzi (DIY) Step by Step how to FIX.

Do you really need a jacuzzi in a spa?

Jacuzzi J-325) Arizona Hot Tub Factory Myth-Busting…Does Size Really Matter in a Hot Tub or Spa that is ? This was just a simple experiment will the water in a larger spa fill a smaller spa without over filling and spilling over.

How to troubleshoot a flashing Flo for a spa?

First verify your spa is receiving the specified incoming voltage into the circuit board as well as out of the circuit board to the transformer. Also, check all fuses for continuity. Next, check the service tag on the side of your circulation pump. This will tell you approximately what voltage your circulation pump should be getting.

Do you need a manual for an Aruba hot tub?

I need a manual for a 1060 Aruba hot tub. When we try to turn the pump on it says FL 1. what do the error codes mean?

What are the error codes for a hot tub?

1) Hot Tub Error Codes (Alphabetical) * * * (3 flashing dots under temp displa Flow/Pressure switch either Open or Clos * * * (as above, & red LED lit up on boa High Limit Fault – – – , – – – ‘Watchdog’ – 48C reached, electronic fau – 01 Hi-Limit fault – 02 Temp sensor fault

What is the FL1 error code for Sundance spa Constance?

We have a Sundance Spa Constance (2011) and today also noticed the FL1 error code. In addition to the code, noticed that the pool is registering 72 degrees when it is set to 101. We have never had a problem with the hot tube, until now. We changed the UV bulb last summer and changed out the filters. Any assistance would be helpful.

What does it mean when your spa says FL1?

January 31, 2014. Reply. Dan typically when you have an FL1 code it means the spa is not heating and won’t heat until the FL1 code is addressed so you want to check with an external thermometer if your water is 72 degrees.

How to troubleshoot FL1 or flashing Flo error codes?

3. First verify your spa is receiving the specified incoming voltage into the circuit board as well as out of the circuit board to the transformer. Also, check all fuses for continuity. Next, check the service tag on the side of your circulation pump. This will tell you approximately what voltage your circulation pump should be getting.

Why is the FL1 code flashing on my Sundance spa?

the TB1 terminal block and then power up the spa. If the pump doesn’t run you could have a bad pump. I have a 2004 Sundance Lagunas Spa that also has the Fl1 error code. I have had them in the past, and was able to reset it with the hose up to the intake trick on many occasions, but not this time.

What to do when your jacuzzi hot tub is not working?

Take off the spa cover to allow the water to cool down and reduce thermostat settings. Switch spa to Programmable Mode in order to turn the heater on solely during programmed filter cycles. Shut the power down to the hot tub and contact the dealer or service technician if the problem continues.

How long does it take to flush a j-335 hot tub?

Automated Operations Approximately two minutes after power is applied to the spa, the first skimming/ heating cycle turns on pump 1. In J-335 and J-345 models, an automatic five minute “blow-out” function also activates pump 2 for a period of five minutes to flush all lines.

What’s the error code on my 2007 jacuzzi?

I have 2007 Jacuzzi J-315 that is showing an FL1 error code. I have 2007 Jacuzzi J-315 that is showing an FL1 error code. I have replaced the flow switch, removed the filters, and put a hose theough the filter connection.

What is the owner’s manual for a jacuzzi?

Control Panel LED Series Hot Tub Owner’s Manual J-315, J-325, J-335, J-345 Models 6530-377, Rev. A Attention New Spa Owner! Congratulations on the purchase of your new Jacuzzi® spa! The following is a list of automated functions performed by your spa.

What to do if your jacuzzi pump is not working?

If the pump seems fine then next would be to check that the pressure switch is not looking corroded or the cable to the pressure switch is making good contact and is not loose. Let me know what you find but no doubt so far either there is a failing circulation pump or most likely the pressure switch is failing and needing replacing.

Is the circulation pump on my jacuzzi working?

Customerreply replied 6 years ago As it turns out, it was not the circulation pump but the flow switch. Took flow switch apart, gummed up at base and burn line in plastic sensor. Replaced flow switch and everything working fine.. Pool and Spa Expert: Mike R., Plumber replied 6 years ago

What does FL2 mean on a hot tub?

While an FL1 error code means the spa isn’t sensing enough water flow to close the flow switch, the FL2 error code means exactly the opposite. So when you are troubleshooting an FL2 error code, we want to determine why the spa thinks the flow switch, or the pressure switch, is providing a closed circuit instead of an open circuit.

What does FL1 mean on a hot tub control panel?

Q: My control panel is flashing the error code “FL1.” What does that mean? A: This is absolutely the most common error code for a service call. However, most of the time, there really is nothing wrong with the spa. Turn your breaker off. Remove your filters.

What to do if you get flashing Flo error code?

1. First thing to do is remove your filter (s). If the error goes away, then it would be a good idea to replace those filters. While it is not a 100% guarantee this is your issue, it could be a contributing factor. 2. Next thing to do is open your cabinet and take a look at your flow switch.

Why does my hot tub have an error code?

Some of the most common hot tub error codes are FLO, FL1 or FL2, and are picked up by flow or pressure switches. The most common causes for this are a dirty or damaged filter, low water levels, air in the pipework or a faulty pump or sensor..

What does no action required mean on a jacuzzi?

No action required.Note: this condition often occurs when filling the spa with water since tap water is usually cold. This only occurs when spa is in Economy mode and stands for “Ice;” means the system has detected a potential condition for freezing and will cause the system to implement freeze protection. No action is needed.