What to do if your hot tub has an error code?

In some instances it may be more prudent to contact a local hot tub service company to assess and repair the spa pack as some diagnose procedures require special equipment. Please note that the Balboa Error Codes cover all circuit board manufactured by Balboa including Cal Spa, Marquis Spa, Master Spa and many others.

What are the message codes on Cal spa?

Beginning with the 2014 product line, Cal Spa control panels display different message codes. For a description of these message codes, see the owner’s manual. Use the problem message from the “Problem Messages” Column to diagnose problem

What does the code OH mean on a hot tub?

OH : Overheat. Spa temp over 108°. HLoH : Hi Limit Over Heat. Hi limit sensor is disconnected, shorted, or spa temp is above 112° F. SEoP : Sensor open or disconnected. Heater disabled but spa operational. SESH : Sensor short, nonfunctional. Heater disabled but spa operational.

What do you need to know about Cal spas?

Cal Spas. Consumers can add a Spa Surround to any of the company’s hot tubs that makes the whole hot tub area look custom to their backyard. Cal Spas is one of the oldest manufacturers of hot tubs in North America and with that comes tremendous experience and a quality product.

Are there error codes for digital hot tubs?

The best thing about digital spas and hot tubs – those with a spa side control panel – is that you are given error codes for most equipment problems. Spa error codes can be somewhat cryptic, but when you have the BIG LIST of CODES, you can immediately define the two or three digit source of trouble.

Why does my hot tub have an OH code?

It is almost always a flow problem. When it’s not a flow problem, it’s usually a bad temp sensor, high limit switch or a stuck relay. Here’s another Cal Spa troubleshooting flowchart for spa error codes OH, including testing the spa heater element for excessive resistance.

What is the spa error code for high temp?

Like our previous discussions on spa error codes, FLO and OH, the sensor codes Sn, Sn1, Sn2… are very much water flow dependent. If water is not flowing through the heater chamber fast enough, it gets too hot, and the safety high temp sensors go into action – just doing their job.

To do this, either turn the wheel or the screwdriver slot on the pressure switch counter-clockwise one full turn (two at the most). If this does not make the code go away, then send the board in for repair or replace it. See complete list of error codes here.

What do you need to know about SPA will not heat?

NOTE: If you have a Printed Circuit Board (PCB) in the main control box please click here for circuit board troubleshooting. The information below is for mechanical control boxes, without circuit boards. “My spa will not heat” is the number one complaint we hear, it accounts for almost every repair that is sent in to Spa Care Center.

What should I do if my spa pressure switch is not working?

Put the wires back on the pressure switch. Run the spa without the filter, if you see the contactor close and you have the proper readings at the heating element then you’ve solved the problem (Replace the Filter). If removing the filter didn’t solve the problem, then the pressure switch should be replaced.

What does the light on the side of a spa mean?

IMPORTANT: Some spas have the thermostats located on top. These are called Spa Side Controls, they have built in air buttons and orange indicator lights. One of the indicator lights says heater, this light comes on regardless if the spa is heating or not. Do not troubleshoot using this light, it could confuse you. Why Does The Hi Limit Switch Trip?

Which is the correct error code for spa?

(Displays when first powered up after refill). Spa operating in Standard Mode. Spa operating in Economy Mode. Safety Suction, Spa is shut down. Spa operating in Standard-in-Economy Mode. Overheat Protection (Heater is deactivated, pumps low speed is activated). Spa water is more than 20° F cooler than the temperature set point.

What does an error code on Sundance spa mean?

Indicates that the flow switch is malfunctioning. The system is disabled in this case and system startup has shorted or has a closed flow switch in this situation. Contact the dealer or a service technician. Indicates that spa needs a new UV bulb. Purchase new UV bulb from dealer and reset countdown timer.

Where can I find a Sun spa review?

You can get to this page by clicking the link in any review, by clicking the red “See the Details Now” banner on the home page, and by clicking the Purchase Private Details link in the navbar at the top of every page Physical Description: Pretty face, nice natural bust – probably C’s.

How long does a Sundance Hot Tub last?

Sundance Spas can last up to 20 years if properly maintained. Sundance Spas come with a warranty that covers five years on parts and labor and 10 years on the shell. How long does it take to heat a Sundance spa? A Sundance hot tub can take anywhere from four to eight hours to heat, depending on outside temperature and the location of the spa.

What should I do if my hot tub heater is not working?

Before proceeding make absolutely sure that the pump which circulates water through the heater is passing water through the heater and also make sure you see water movement in the spa! If you don’t confirm water is moving in the hot tub and through the heater do not proceed with the next step as in doing so may burn out the heating element.

What should the voltage be on a hot tub circuit board?

If you DO have 220 volts across both hot wires coming from the house, then next measure the voltage across both heating element pins. You should see 220 volts. If you do not, then the circuit board is faulty and will need to be replaced or sent to us for repair.

Is the heat indicator light on on my hot tub?

No, It Is Not: If you are not getting any error messages in the display screen (blinking dots is an error message) then please proceed, otherwise find the steps below to troubleshoot error messages. In order for the spa to heat, the heat indicator light needs to be on on the topside control.

What should the water temperature be in a hot tub?

For most healthy adults, a water temperature of 100 degrees F is safe, according to the US Consumer Product Safety Commission (CPSC). At this temperature, you will receive all of the benefits from warm water therapy and a great relaxation experience. According to the CPSC, water temperature should never exceed 104 degrees F.

What should the temperature be in a spa heater?

Temperature in the spa heater housing is below 40° F. Status of the heater element is unknown. The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. Over heat. The spa is at a temperature above 108° . Do not use spa when temperature is flashing or the OH message is displayed.

What should I do if my hot tub is overheating?

Turn off all power to the hot tub as soon as you realize it is overheating. The spa should have an automatic shut off when the water temperature reaches about 112 degrees fahrenheit. Call your hot tub dealer or manufacturer for service options.

When does a hot tub need to be shut off?

The spa should have an automatic shut off when the water temperature reaches about 112 degrees fahrenheit. Call your hot tub dealer or manufacturer for service options. There are a variety of conditions that could lead to the overheating of your hot tub, but may differ in various hot tub models and brands.

When do I need to reset my hot tub control panel?

If your hot tub control panel isn’t working then when it can be really frustrating. Having said that, sometimes all you need to do is a simple reset on your hot tub control panel to clear the problem and to get it back into action.

Do you need serial number for hot tub?

Keep your spa’s serial number on hand in case you need to reference it for more troubleshooting advice or official parts and repairs. You don’t have to be tech savvy to solve some of the common problems that arise with regular hot tub use; just learn to be more proactive.

What to do when your hot tub pump is not working?

When your hot tub pump is dead… If there is no action coming from your circulation pump, see if your control panel is giving you an error code, typically a FLO or OH error when dealing with a dead pump. Check that your power is on, the breaker or GFCI test button are not tripped, all valves are in the open position.

How to know if your hot tub is overheating?

Hot Tub Topside Keypad Error Codes & Messages 1 Balboa. OH = Sensors reading 112-118° F. OHH = Overheat. Spa has shut down. One sensor has detected 118° F at heater. 2 Brett Aqualine 3 CTI. OH = Overheating, water over 112° F. System will restart when temp. drops. HL = High limit switch tripped. 4 EasyPak 5 Gecko 6 Hercules 7 Hurricane 8 Hydro-Quip

What does it mean when your hot tub is dry?

Newer hot tubs have a digital display for error codes that can assist with troubleshooting. A message such as “dr” or “dry” or “heater dry” is a warning that there’s no water in the heater tube, says Niagara Hot Tubs.

How to fix spa code of ” Dr ” and ” dry “?

Also when the tub is initially powered up the blowers go on and remain on regardless of me turning them on/off via my balboa TP600 top side panel. Would you happen to know a way that I can troubleshoot or correct those error codes? Any help would be greatly appreciated. Re: Spa code of “Dr” and “Dry”. How does one fix this issue? PLEAS HELP!!

What is the code for a gecko hot tub?

Gecko Error Codes also cover any control box manufactured by Gecko and Spa Builders. Click on any Blue error code below for a description of causes, troubleshooting and repair information. CoLd : Temp in heater housing is below 40° F. Low speed / circ pump will operate continuously until the temp rises above 45° F. OH : Overheat.

What does blinking red light on hot tub control panel mean?

Blinking Red Light. A blinking red light on the control panel may indicate it needs to be reset. For most models you will turn off the power to the spa for a minute or two and then turn it back on. Turn on the lower amp breaker first if you have a hot tub powered by 240 volts.

Can you lock a hot tub when not in use?

Any amount of locks will not work unless you keep the hot tub cover on when not in use. Make it a priority that when the hot tub is not being used, that the cover will be replaced and locked. If you do have a gate, that should also be closed and locked.

What is the Hi limit on a hot tub?

Hi Limit Over Heat. Hi limit sensor is disconnected, shorted, or spa temp is above 112° F Circuit Board temperature has exceeded acceptable limit. System will restart when temp. drops Freeze protection. No action is necessary Freeze condition. 55ºF detected. Low speed pump and heater will activate until spa reaches 65ºF

Why does my hot tub have an error message?

Hot tub control panel error messages – If your hot tub control panel has been showing an error message you will want to know how to clear it. Even if you have sorted out the problem that the error message is indicating it might still be continuing to show as a problem on the control panel.

Where is the control panel on my hot tub?

For a control panel that is built into the hot tub if you have a look inside the service bay of the hot tub you will probably see that it is also connected to the hot tub via a cable which will no doubt be plugged in somewhere. Again check for corrosion.

What to do if your hot tub is not working?

If the error signal continues on the control panel then you will need to consult your hot tub manual to see what the problem is. If the control panel simply seems not to be working you can check the connections to it and also see if any water has got in it which could be the problem.

What to do if your Sundance Spa hot tub is not working?

If condition persists, contact your Sundance Spas dealer or qualified service technician. If the hot tub water is more than -7C cooler than the temperature set point, jets pump #1 and heater will automatically activate to provide freeze protection.

If however you have the fault then the first thing to do is shut the spa down, do not empty, remove the filter and make sure all the jets are open (as best you can). Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

What to do if your Hydropool Hot tub does not reset?

Remove the spa cover and allow water to cool. Once the heater has cooled, reset by pushing any button. If the hot tub does not reset, shut off power to the spa and call your supplier for a service. DO NOT ENTER THE WATER. Remove the spa cover and allow water to cool. At 41.7 the spa should automatically reset.

What to do if your hot tub high limit switch is damaged?

Simply reset by pressing the big red button on your spa pack. The high limit switch may be housed in a thermowell. If the water temperature in the thermowell is the same as the water temperature in the rest of the spa, the switch is damaged and needs to be replaced.

Why is my Beachcomber Hot Tub not resetting?

My Beachcomber Hot tub control panel is showing “FL” and will not reset. What is the possible fault and can I do My Beachcomber Hot tub control panel is showing FL and will… When the door was closer and the cycle was started it started making a clanging sound and the FL code symbol was showing.

What causes a FL2 error code on a hot tub?

Generally speaking, an FL2 error code is caused by one of two components, and for three different reasons. The first reason would be that the flow switch/pressure switch has failed and is delivering a closed circuit at all times.