What to do if your hot tub control panel is not working?

If your hot tub control panel still isn’t working properly or displaying properly then there are a number of things that you can try to see if you can get it working again. However, if your hot tub is still under warranty then you should consult your dealer rather than trying to fix the problem yourself.

What does it mean when your hot tub light is blinking?

Blue Logo “Power” indicator blinking = Heater high-limit thermostat tripped. • Disconnect power for at least thirty seconds to reset heater high limit. If it will not reset, check for clogged filters. If tripping continues, call for service. Sn1 = Nonfunctional high temperature sensor.

Why does my hot tub have an error message?

Hot tub control panel error messages – If your hot tub control panel has been showing an error message you will want to know how to clear it. Even if you have sorted out the problem that the error message is indicating it might still be continuing to show as a problem on the control panel.

What to do when your status light does not blink?

If the status light does not start blinking after 90 seconds, release the gas control knob, turn the gas valve off, and wait 10 minutes before attempting to relight the pilot. On newly installed water heaters, it may take up to 2-3 lighting attempts before the pilot lights and the status light starts blinking.

Why does my hot tub control panel keep blinking?

If there is any condensation, dry it off. A blinking red light on the control panel may indicate it needs to be reset. For most models, you will need to turn off the power to the spa for a minute or two and then turn it back on again. Turn on the lower amp breaker first if you have a hot tub powered by 240 volts.

Where is the control panel on my hot tub?

For a control panel that is built into the hot tub if you have a look inside the service bay of the hot tub you will probably see that it is also connected to the hot tub via a cable which will no doubt be plugged in somewhere. Again check for corrosion.

Why does my hot tub have a flashing Flo message?

If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter. It’s very important to remember that if you just finished fresh filling your spa then you could also have had an air lock that caused a Flashing FLO message. By removing the filter you just removed the air lock.

Examine the panel to see if any moisture is inside the display. See if the panel or any buttons are cracked or if it could have possibly gotten wet. If only part of the control panel is not working, check for any blinking lights or error messages.

What does the topside Control Panel on a hot tub do?

And that’s all the topside control is – a control panel, think of it as a remote control for your hot tub, wired into your spa controller, which is really the brains of the spa system. The spaside control panel, it’s just a convenient way to turn things on and off, and view equipment status lights and water temperature.

How to troubleshoot a spa side control panel?

Spaside Control Panel Buttons Not Working Correctly 1 Check for moisture under glass or on contacts 2 Check cable for any rodent damage, crimping or melting 3 Clean plug-in cable connections at both ends 4 Membrane or touch pad buttons may be faulty 5 Inspect circuit board for damage and correct power output 6 Replace topside control

Why does my hot tub keep Tripping the GFCI?

The tripping of the GFCI may be caused by a component on the spa or by an electrical problem. Such electrical problems include, but are not limited to, a faulty GFCI breaker, power fluctuations or a miswire.

What to do if your Spa circuit board is not working?

When your hot tub or spa is not working like it should, the circuit board is one of the first things to check. If it turns out it is working fine, then you can move on to other systems in your hot tub. The first thing to do, just like with your old personal computer, is to turn off the spa and turn it back on.

Why are there flashing dots on my spa control panel?

If the spa has shut itself down before an actual overheat, Temperature and/or Hi-Limit sensors may be faulty. Nothing is operating, and there is an error code or flashing dots or lights on my control panel. There are as many different error messages as there are different brands of spas.

What does blinking red light on hot tub control panel mean?

Blinking Red Light. A blinking red light on the control panel may indicate it needs to be reset. For most models you will turn off the power to the spa for a minute or two and then turn it back on. Turn on the lower amp breaker first if you have a hot tub powered by 240 volts.

What’s the reset button on an old spa?

Older spas used mechanical Temperature and Hi-Limit switches. This type of Hi-Limit can usually be reset by pushing in its reset button, a red or black button located on the heater or equipment pack (see your spa manufacturer’s instruction manual for exact location on your spa).

How to troubleshoot an issue with your spa?

To troubleshoot an issue with your spa, locate your specific problem in the chart below to help determine a probable cause, and then apply the right solution. Do you need to call a professional technician? Do you need to call a professional technician? Adjust the total alkalinity and pH.

Why does my dead Spa have no power?

The greater disappointment is not being able to use the spa at that moment. If you’ve ever found a “dead spa” with no power, no indicator lights, nothing at all – this post is for you. Here, we outline the seven most common reasons that a hot tub has no power.

What to do if your Bullfrog spa pump is not working?

The wet-end of the pump has a bleed valve—loosen this until all the air escapes and water starts to drip out, or loosen the union on the pump to let the air out until you see water. Do not attempt this while the spa pump is running. If you need help doing this or this does not resolve the problem, please contact your authorized Bullfrog Spa Dealer.

What does it mean when your hot tub is not heating?

Please try again later. Here’s some helpful advice if your hot tub is not heating. If your hot tub “heat light” or “heat icon” is showing up on the display but the water is not warm then that usually means that you have a bad circuit board. Visit for more advice. Thank you! Loading…

Is the heat indicator light on on my hot tub?

No, It Is Not: If you are not getting any error messages in the display screen (blinking dots is an error message) then please proceed, otherwise find the steps below to troubleshoot error messages. In order for the spa to heat, the heat indicator light needs to be on on the topside control.