What to do if your Cal spas heater wont turn on?

Raise the temperature on the control panel. If the HL or HFL message appears on the control panel, the pressure may be defective. This will shut down the heater. Call your dealer or Cal Spas customer service. A heating mode may not be selected. See control panel instructions in your owner’s manual.

Why does my calspa hot tub overheat?

1) Is the filter timing (FC, F2, F4, F6, FC, etc…) set to the proper code? I found on my CalSpa if it was set at F6, F8, or FC, it would overheat the water and shut-off. This is because it requires an additional motor for those cycles.

How to reset spa message on calspas.com?

Press any button to reset or wait 15 minutes and spa will automatically reset. If message spa does not reset, call customer service. Insufficient water detected in heater. Spa is shut down. (Displays on third occurrence of dr message.) Follow directions for dr message and press any button to reset spa.

What should the temperature be when the power goes off on a spa?

Contact your dealer for more assistance. If power to the spa was shut off, the temperature may have reset after the power was restored. The automatic default for temperature is 100°F. If power goes off and then comes back on, the spa may reset to factory default temperature of 100°F.

How to troubleshoot a problem with a Cal spa?

Troubleshooting 1 Message on the control panel. A message on the control panel may indicate a problem. 2 Problems starting up. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. 3 Power and electrical problems. 4 Heat problems 5 Jet problems 6 Water pressure problems

What’s the code for a Cal Spa hot tub?

I’ve learned the F2, F4, F6, F8, and FC codes from Cal Spa’s current manuals. I get a OH code (I assume Over Heating) and the tub gets 108+. I have it set on F2 (sometimes F4: I understand F8 or FC can be a problem unless there is a special motor). However, the tub still gets to 105+.

When did I start priming my Cal spa pump?

Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. Beginning with the 2014 product line, Cal Spas pumps have a different method of priming. See the 2014 owner’s manual for a full description. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier.

How does a caldera hot tub pump work?

In a Caldera Vacanza® Series spa, you’ll find the main pump that powers the jets and a circulating pump that maintains the water’s condition and temperature. Above both is a PVC pipe and a fitting (a union) that joins the pipes to the water pump.

What happens when the water pump is off in a spa?

1. Water temperature is unknown. 2. Spa is in Economy or Sleep mode. 1. After pump has been running for 2 minutes temperature will be displayed.breadcrumb breadcrumb 2. In Economy or Sleep mode, the pump may be off for hours outside a filter cycle.

What kind of heater does a Cal Spa use?

Spa Components replacement heater for select Cal Spas that use a 15 1/2 inch x 2 inch heater. This 4.5kW heater is part B24045G that replaces heater models 20-00422 , 20-00429 , 48-3300-10-321H , B24045G , B24055G , C2450-0521 , C2550-0321-A

Is there a problem with my caldera hot tub pump?

This doesn’t mean that there’s an issue with the pump; it simply means that you’ll have to rule some things out to get to the root of the actual problem. As always when troubleshooting, have your Owner’s Manual handy. On Caldera Utopia® Series spas, the logo light serves as a helpful and visible diagnostic tool.

What kind of heater do you need for a Coleman hot tub?

4kW 240V (or 1kW at 120V) replacement spa heater used in Coleman and other brand hot tubs. This heater comes WITH PRESSURE SWITCH INCLUDED. Free shipping in the continental USA. C2400-0535-TPS is a Balboa Instruments style stainless steel heater… Spa Components replacement heater for select Cal Spas that use a 15 1/2 inch x 2 inch heater.

What does it mean when your spa heater is disabled?

Heater Flow is Reduced-means there is inadequate water flow to heater to carry heat away from the spa unit’s heating element. The heater is disabled. Check to determine conditions such as closed valves, suction flow restrictions, pump prime, low water level, trapped air and too many closed jets. Heater starts again after 1 min.

Why is the heating element on my spa not working?

If for any reason one of these components fail then the required voltage to the coil will be jeopardized and the contactor will not close in order to send power to the heating element. As mentioned above, it is usually one of these components that will cause a spa not to heat.

How can I tell if my Spa is heating or cooling?

IMPORTANT: Some spas have the thermostats located on top. These are called Spa Side Controls, they have built in air buttons and orange indicator lights. One of the indicator lights says heater, this light comes on regardless if the spa is heating or not.

How big is a Cal Spa hot tub heater?

Cal Spa 5.5kW Heater HEA14100451 that connects to 2 inch inner diameter plumbing. This is a 19 1/2 inch total length heater that includes the tailpieces. Titanium heater for longer lasting heat. Titanium flow through type heater…

When did Cal spas start making hot tubs?

Cal Spas was founded in 1979, and they currently offer more than 250 product models. Each of their hot tubs can be customized from a list of thousands of options, and the company places an emphasis on innovative touches and quality workmanship.

When do I need to Reset my spa heater?

A spa heater may need to be reset if it has tripped or stopped working. Using the high-limit reset switch and checking all breakers and GFCI outlets can reactivate the spa’s heater. A spa heater has a high-limit reset button.

When to replace a Cal Spa hot tub?

We also carry replacements for major components such as pumps, blowers, heaters, and controllers If your Cal Spas ® hot tub is broken and your spa pack is over 8 years old, your surest and most economical solution is to replace the entire spa pack rather than to try to fix the one broken component.

Are there any replacement parts for Cal spas?

Spa Guts provides universal replacement fits for all brands of spas, including Cal Spas ®. Spa Guts hot tub parts are not manufactured or endorsed by Cal Spas ®, nor is Spa Guts in any way associated with Cal Spas ® .

Is there a warranty on a Cal spa?

Spa Guts spa packs and controls are backed by our 3-year warranty . Our customers who own Cal Spa ® hot tubs report greater satisfaction with our spa packs than with their original ones. If this is all new and confusing to you, start here . Spa Guts provides universal replacement fits for all brands of spas, including Cal Spas ®.

What to do if your spa does not reset?

If spa does not reset, shut off the power to the spa and call customer service. Spa is shut down. The sensor that is plugged into the sensor “A” or “B” jack is not working. If the problem persists, call customer service. (May appear temporarily in an overheat situation and disappear when the heater cools.)

What causes a heater in a spa to not heat?

Some other things to check are: 1 Faulty heater Contactor 2 Burnt wires 3 Fuses and/or breakers at spa or house 4 Faulty thermostat

What to do if your spa pump is not working?

With over 25 years of experience, we’re equipped to help with any spa issues you have or to discuss a new spa. When your spa pump is making noises… This usually happens if you recently drained the spa. Open the lock nut until you hear air hissing, then tighten up again as water begins to leak.

What are the message codes on a Cal spa pump?

Beginning with the 2014 product line, Cal Spa control panels display different message codes. For a description of these message codes, see the owner’s manual. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. Beginning with the 2014 product line, Cal Spas pumps have a different method of priming.

What does message on Cal spa control panel mean?

A message on the control panel may indicate a problem. Note: The message troubleshooting shown here applies to Cal Spa control panels built in 2013 and earlier. Beginning with the 2014 product line, Cal Spa control panels display different message codes. For a description of these message codes, see the owner’s manual.

What should I do if my spa water is overheating?

Under this mode, the pump will run the low speed every 30 minutes approximately to check the water’s temperature and to start heating if required. Please leave the Spa Cover off for a few hours and either reduce the set temperature or change the heating mode to Rest Mode to allow the pump to cool down.

What do you need to know about SPA will not heat?

NOTE: If you have a Printed Circuit Board (PCB) in the main control box please click here for circuit board troubleshooting. The information below is for mechanical control boxes, without circuit boards. “My spa will not heat” is the number one complaint we hear, it accounts for almost every repair that is sent in to Spa Care Center.