What to do if your Bullfrog spa pump is not working?

The wet-end of the pump has a bleed valve—loosen this until all the air escapes and water starts to drip out, or loosen the union on the pump to let the air out until you see water. Do not attempt this while the spa pump is running. If you need help doing this or this does not resolve the problem, please contact your authorized Bullfrog Spa Dealer.

Why is my Bullfrog hot tub making a burning noise?

If your spa pump is creating a burning smell or making excessive noise, the pump motor is defective. This can happen when running the pump during high ambient outside temperatures or due to excessive run times. Please contact your authorized Bullfrog Spas dealer for replacing the pump.

Where is the serial number on a bullfrog spa?

letin from Bullfrog Spas. Your spa’s serial number is located both on the base under the equipment door and the Manufacturing ID Label located inside the equipment compartment of your spa. For the safety of all those who utilize your spa and its surroundings, please make sure your spa and any adjoining installations, including the electri-

How to prevent airlocks in a bullfrog hot tub?

To prevent airlocks when filling your spa, be sure to open all valves in the JetPaks and all other jets in the spa before filling to allow as much air as possible to escape from the system during the filling process. Fill your spa through the filter by taking the filter cap off and put the hose directly in the filter.

How many hot tubs does Bullfrog Spa have?

There are 8 spas in the premium A Series from Bullfrog Spas. This luxury series has hot tubs with upgraded features that come standard, including: a rigid cover, an EternaWood cabinet, 2 dual speed pumps, a circulation pump, interior and exterior LED lights and stainless steel jets.

When to drain a bullfrog hot tub manifold?

If the leak is at a jet, manifold or in other areas of the plumbing, it is probably a good idea to drain the spa before doing any of the repairs to avoid a new frog swamp near the spa.

Where are the service valves on a bullfrog hot tub?

Service valves are located to the left and right of the spa pack and each of the main pumps to facilitate repairs without needing to drain the spa. (Service or slice valves are not available on models 331, 231, 251, 362, 131, 151, or 162.)

How to troubleshoot a bullfrog hot tub breaker?

Disconnect one component at a time from the control board and try restarting the spa. If the breaker trips, reconnect the component then try again by disconnecting a different component. Continue repeating this process until the breaker does not trip. Components include pumps, heaters, lights, stereos, ozone, etc.

What should water temp be in Bullfrog hot tub?

Open the cover for several minutes, long enough to allow the water to cool down. Repeat a couple times weekly as necessary. For safety reasons, never leave your spa unattended with the cover open. If OHH is displayed on the control panel, this means that the thermometer has detected spa water temperature above 110 degrees F.

How to clean hard water stains on a bullfrog hot tub?

To clean hard water stains, remove light scratches and protect your spa shell, contact your authorized Bullfrog Spa dealer. With normal use of the spa, oils, lotions, and hair spray will build up on the surface of the water. This can leave a residue line around the perimeter. This can be easily removed using a spa surface cleaner or its equivalent.

Where can I buy a bullfrog hot tub?

Your local authorized Bullfrog Spa dealer will help you purchase, install, and service your hot tub. Design Studio allows you to choose the spa model and layout you want, the JetPaks you need, and the colors that complement your home and landscape. Design the best hot tub for you and your needs. Still Have Questions?

Are there any problems with a bullfrog spa?

Built without wood or metal, your Bullfrog Spa will never rot or corrode. Unnecessary holes and plumbing used in conventional spas were eliminated to prevent leaks and failures. Rest easy knowing you’re investing in a trouble-free spa.

What are the chase ways on a bullfrog spa?

Each Bullfrog Spa is manufactured with three electrical access chase ways in its base to allow conduit to be run to the spas control system. These chase ways are marked by stickers indicating access points.

Where can I find the owner’s manual for Bullfrog?

All Bullfrog Owner’s Manuals are available in Adobe Acrobat format (PDF). If you are not able to view the manual’s please download Adobe Reader. Owner’s Manual files are large and may take a few minutes to download. You are unique and your hot tub should fit your unique life.

If the leak is at a jet, manifold or in other areas of the plumbing, it is probably a good idea to drain the spa before doing any of the repairs to avoid a new frog swamp near the spa.

What’s the best way to do a frog pump?

Squeeze your abs and glutes as you push your hips towards the ceiling. Hold this position for a few seconds, tensing your abs and glutes the whole time. Slowly lower your hips towards the ground. This is one whole frog hip thrust. Repeat for the desired number of reps.