What to do if you get flashing Flo error code?
1. First thing to do is remove your filter (s). If the error goes away, then it would be a good idea to replace those filters. While it is not a 100% guarantee this is your issue, it could be a contributing factor. 2. Next thing to do is open your cabinet and take a look at your flow switch.
How to troubleshoot a flashing Flo for a spa?
First verify your spa is receiving the specified incoming voltage into the circuit board as well as out of the circuit board to the transformer. Also, check all fuses for continuity. Next, check the service tag on the side of your circulation pump. This will tell you approximately what voltage your circulation pump should be getting.
What does a flashing Flo on a circ pump mean?
Typically Solid FLO msgs are related to a blockage, bad Flow switch and or connection, summer logic, bad PWA. Typically the circ pump would be off with a Solid FLO. A Flashing FLO msg could mean other things like a soiled filter, low water level, stuck weir door (not enough water supply to circ pump).
What to do if your GFCI is flashing Flo?
Make sure there is nothing in the filter area and turn your GFCI back on again. If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter.
1. First thing to do is remove your filter (s). If the error goes away, then it would be a good idea to replace those filters. While it is not a 100% guarantee this is your issue, it could be a contributing factor. 2. Next thing to do is open your cabinet and take a look at your flow switch.
Typically Solid FLO msgs are related to a blockage, bad Flow switch and or connection, summer logic, bad PWA. Typically the circ pump would be off with a Solid FLO. A Flashing FLO msg could mean other things like a soiled filter, low water level, stuck weir door (not enough water supply to circ pump).
What should I do if I get a Flo error on my spa?
Some of them may require a skilled technician to come out and work on your spa for you. 1. The first thing to do if you have a FLO error is to remove your filter and clean it. A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter.
What does Flo mean on a water heater?
I have an Aquacal heat pump as well. The code FLO means “Low or No Water Flow Detected”. It is a self-protection mechanism that prevents the heater from operating if there isn’t enough water moving through the heat exchanger.
Which is most common error code FL1 or Flo?
The flow errors FL1 and FLO are the most common error codes we get calls about. As people read through their owners manual, it is easy for people to quickly come to the conclusion that the first thing they need to replace is their flow switch.
Some of them may require a skilled technician to come out and work on your spa for you. 1. The first thing to do if you have a FLO error is to remove your filter and clean it. A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter.
What does Flo error on my Sundance spa mean?
A FLO error is going to indicate something is wrong with your circulation system, so start with the simplest problem: your filter. Even if you think it should be fine, give it a try. Sometimes we can’t see the problem with our eyes.
The flow errors FL1 and FLO are the most common error codes we get calls about. As people read through their owners manual, it is easy for people to quickly come to the conclusion that the first thing they need to replace is their flow switch.
Why did my Sundance 880 get a FlO2 error?
Have a 2010 Sundance Optima 880 spa (OXO3LCD-100378459-0710) giving me FLO2 error. After dropping the curtain to look for the flow switch (and giving it 2 power cycles) it came back to life. When it wasn’t running, flow switch open—closed once flow resumed.
When do I need to replace my flow switch?
If your flow switch appears visually closed, and you test across those two wires, your should be getting roughly 0 ohm’s or no resistance. If you are showing any other results, then you most likely need to replace the flow switch. 5.
Why does my hot tub have a Flo message?
The message can also be caused by soiled filters, plugged or bad Flow switches or a bad connection from the Flow switch to the PWA. In rare instances a bad PWA could cause a solid FLO message. If the pump checks out try and look at the filter, the circ line, the wiring to the Flow switch and the Flow switch.
Does the FlO2 display tell me to replace flow switch?
Standing by. the tub is a 2005 majesta series 880 by sundance. yes i am at the tub now. i do have the panel open Thank you for that information. That means that your particular hot tub uses a flow switch to detect flow through the heater. FLO2 in your case, means the flow switch was closed before the circulation pump started.
If your flow switch appears visually closed, and you test across those two wires, your should be getting roughly 0 ohm’s or no resistance. If you are showing any other results, then you most likely need to replace the flow switch. 5.
What to do if your spa error code is Flo flow?
Proceed step by step, and you should be able to find the cause of the FL, FLO, FLOW or LF error code. If you need further assistance with spa trouble codes, feel free to give us a call at 800-770-0292.
What does F8 E1 or LF or Lo fl error code mean?
If the washer has an F8 E1, LF, or LO FL error, the door will be locked, and the control will be unresponsive. Press the power button, and the washer will start a drain routine which takes approximately 8 to 10 minutes, during which time the pump will run continuously.
Proceed step by step, and you should be able to find the cause of the FL, FLO, FLOW or LF error code. If you need further assistance with spa trouble codes, feel free to give us a call at 800-770-0292.
If the washer has an F8 E1, LF, or LO FL error, the door will be locked, and the control will be unresponsive. Press the power button, and the washer will start a drain routine which takes approximately 8 to 10 minutes, during which time the pump will run continuously.
How to test the flow switch on a circ pump?
Now, if your circ pump is running and the flow switch appears physically in the closed position, then test the flow switch. 4. To test the flow switch, set your meter to ohm’s. If your flow switch appears visually closed, and you test across those two wires, your should be getting roughly 0 ohm’s or no resistance.
Now, if your circ pump is running and the flow switch appears physically in the closed position, then test the flow switch. 4. To test the flow switch, set your meter to ohm’s. If your flow switch appears visually closed, and you test across those two wires, your should be getting roughly 0 ohm’s or no resistance.
