What should the circulation pump settings be on a Sundance spa 880?
I have a Sundance Spa 880 Series at my new residence and I am wondering what the recommended setting is for the filter/circuation pump. Currently it is set on “Standard Mode” and continuously runs. In my previous residence I had an Arctic Spa that was set to circulate intermittently.
Why does my water pump make a humming sound?
If your water pump has stopped pumping out water entirely while making this buzzing sound, there’s no cause for panic. The humming sound means the pump is working but there’s no water to move, so your pump is running dry. If your pump has lost prime, or is running dry, this is due to a loss of water.
Why does my hot tub pump hum when I turn it on?
When I turn on the power to my hot tub at the breaker, I can hear the relays closing and the pump hums for a short while, but it doesn’t turn. I recently drained and filled my hot tub. After refilling, I ran the pump for a few minutes to circulate some chemicals, so it was working at the time.
How often should I Run my Sundance spa?
Most people run your Series of Sundance spa in Standard mode with a 24hr circ pump run time 12 months a year. Setting it up this way and always having a clean micro filter lessens the chance of the water chemistry and water clarity getting away on you. Also make sure that your ClearRay Uv lamp has not expired and or your ozone is still operational.
What to do if your Sundance spa heater is not turning on?
Heater is deactivated and pump may not turn on. Flow/pressure switch is defective. These steps should only be taken after checking and testing the above steps. With the circ pump and the main pump off, test switch operation with an ohmmeter in the continuity position, test for continuity across switch terminals.
What kind of circulation pump does Sundance Spa use?
Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.
Why does my circ pump make a humming noise?
Gurgling, humming or grinding noises on a spa circulation pump are good indicators of a problem. It could be Air, Scale or a Clogged Impeller. Maybe a dirty spa filter. Or, it could be the bearings in the motor going bad. AIR IN THE LINES: If you have just drained the spa, you may have an air lock on the circ pump.
When I turn on the power to my hot tub at the breaker, I can hear the relays closing and the pump hums for a short while, but it doesn’t turn. I recently drained and filled my hot tub. After refilling, I ran the pump for a few minutes to circulate some chemicals, so it was working at the time.
Heater is deactivated and pump may not turn on. Flow/pressure switch is defective. These steps should only be taken after checking and testing the above steps. With the circ pump and the main pump off, test switch operation with an ohmmeter in the continuity position, test for continuity across switch terminals.
Why is my Spa 2 speed pump not working?
II have a 2002 Optima spa. Several months ago the button on the top-side control panel for the 2 speed pump (#1) stopped working. There’s a second, smaller control panel on the opposite side of the tub which also will not work. But when the preset filter cycles occur the pump will come on and the icon comes on on the display.
II have a 2002 Optima spa. Several months ago the button on the top-side control panel for the 2 speed pump (#1) stopped working. There’s a second, smaller control panel on the opposite side of the tub which also will not work. But when the preset filter cycles occur the pump will come on and the icon comes on on the display.
What are the manuals for the Sundance spa?
Find out how to use, care for, and program your Sundance ® spa by browsing the manuals and guides below. (2020) 880™ Series Manual – (Aspen®, Maxxus®, Optima®, Cameo®, Altamar®, Marin®, Cambria™, Capri®) (2020) 780™ Series Manual – (Chelsee®, Hamilton™, Montclair™, Bristol™, Hanover®, Dover™)
How long does a Sundance Spa hot tub last?
The hot tub is programmed with a default setting starting at 12:00 AM and lasting for 8 hours, but this can be changed. This cycle addition to the normal operation. filter cycle. For example, the primary filter cycle is set to 8 hours every water after the cycle has finished. The next primary filter cycle will only be for 6 hours not 8 hours.
How to do 24 hour filtration at Sundance spa?
Select 12 AM for 24 hour filtration. Press the check mark button to confirm and activate the setting. Press the “Return” button (Top right hand corner) to return to the “Heat & Filter” menu. Back on the “Heat & Filter menu”, Press “2” for Secondary Filter, and select “Infrequent”, “Frequent” or “Away” mode.
What’s the start time on a Sundance 880?
880 & 980 Series: Press the “Menu” button to enter the settings menu. Select “Heat & Filter”. Select “1” for Primary Filter. Adjust “Start Time” as required and press the check mark button to confirm and activate the setting. Select 12 AM if you are planning on using 24 hour filtration.
Select 12 AM for 24 hour filtration. Press the check mark button to confirm and activate the setting. Press the “Return” button (Top right hand corner) to return to the “Heat & Filter” menu. Back on the “Heat & Filter menu”, Press “2” for Secondary Filter, and select “Infrequent”, “Frequent” or “Away” mode.
How to set heating mode on Sundance spa 680?
Here are the instructions for setting the Heating Mode on your Sundance Spa. 680 Series: Press the “Menu” button repeatedly until you get to the “HEAT” menu. Use the temperature up or down buttons to scroll through heating options.
Where does Sundance Spas make their hot tubs?
They are based out of California, and their products are sold in more than 60 countries. Sundance® Spas focuses on creating acrylic spas, and they are rated as the top worldwide distributor and manufacturer of this particular style. They also produce in-ground and portable hot tub models.
What does an error code on Sundance spa mean?
Indicates that the flow switch is malfunctioning. The system is disabled in this case and system startup has shorted or has a closed flow switch in this situation. Contact the dealer or a service technician. Indicates that spa needs a new UV bulb. Purchase new UV bulb from dealer and reset countdown timer.
Why is my Sundance Spa having trouble shooting?
1. Dirty Filter: even when you have cleaned the filter, the filter may be impacted and be time for a new filter. The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter.
880 & 980 Series: Press the “Menu” button to enter the settings menu. Select “Heat & Filter”. Select “1” for Primary Filter. Adjust “Start Time” as required and press the check mark button to confirm and activate the setting. Select 12 AM if you are planning on using 24 hour filtration.
I have a Sundance Spa 880 Series at my new residence and I am wondering what the recommended setting is for the filter/circuation pump. Currently it is set on “Standard Mode” and continuously runs. In my previous residence I had an Arctic Spa that was set to circulate intermittently.
How long does it take to drain a Sundance Hot Tub?
Run Jet pumps for 2 hours (make sure all jets are running and have not been manually turned off). You will need to turn the jets back on every 20 minutes. You are ready to begin draining your Sundance Hot Tub. Once you are ready to drain your Sundance hot tub, switch the power off at the GFCI breaker.
1. Dirty Filter: even when you have cleaned the filter, the filter may be impacted and be time for a new filter. The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter.
What’s the fastest way to drain a Sundance Hot Tub?
In addition to these drains, there are other options available to you. The Quick Drain, Available at all 5 locations of The Sundance Spa Store ( Burlington, Mississauga, Oakville, St. Catharines & Vaughan) is up to 5 times faster than the gravity drain, removing 10-12 gallons of water per minute and there is no extension cord required!
How long does a Sundance Hot Tub last?
Sundance Spas can last up to 20 years if properly maintained. Sundance Spas come with a warranty that covers five years on parts and labor and 10 years on the shell. How long does it take to heat a Sundance spa? A Sundance hot tub can take anywhere from four to eight hours to heat, depending on outside temperature and the location of the spa.
What is the error code on the Sundance Spa hot tub?
Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.
What kind of warranty does Sundance Spas have?
Each Sundance Spas series comes with a warranty that covers the shell, cabinets, plumbing, equipment, controls, components, parts and accessories. The Sundance Spas warranty also protects against water loss caused by defects in the shell for five to 10 years, depending on the model you purchase.
What to do if your Sundance spa switch is defective?
Disconnect wires from Switch terminals. Set ohmmeter in the continuity position. Measure resistance across switch terminals for infinite resistance with pump off. If continuity is measured with pump off, the switch is defective. (Or debris blockage, l which you have to remove switch and inspect.
Most people run your Series of Sundance spa in Standard mode with a 24hr circ pump run time 12 months a year. Setting it up this way and always having a clean micro filter lessens the chance of the water chemistry and water clarity getting away on you. Also make sure that your ClearRay Uv lamp has not expired and or your ozone is still operational.
Why does my Sundance spa go into Oh error code?
Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code
What happens when Sundance spa goes into watchdog?
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.
Who is the owner of the Sundance spa?
Our patented Fluidix® jets were co-developed with Bowels Fluidics Corp, experts in the field of Fluid Dynamics. Discover how you can enjoy the next generation of spa ownership, making it easier than ever to use and maintain your Sundance® spa.
What are the different types of Sundance Spas?
We have spa parts for all Sundance Spas models such as maxxus, maximus, optima, cameo, majesta, altamar, capri, caprio, hamilton, chelsee, aspen, certa, montclair, dover, denali, tacoma, ramona, peyton, mckinley, burlington, bahia, palermo, kingston, claremont
