What should I do when filling my Sundance Hot Tub?
When adding new water to your Sundance hot tub, Put your hose into the filter well so that it runs through the pipes as it fills up, This will help prevent air locks upon re-start. Once your hot tub is filled, You can turn the power back on so it can begin heating up (Do not power up the hot tub until the hose has been removed).
How big of a leak do you need for a hot tub?
For all types of spas, hot tubs, and pools. For leaks in walls, floor, housing, return lines, suction lines, skimmers, fittings, etc. For water loss in spa / hot tubs of less than 3 mm per day. For water loss in pools of less than 5 cm or 50 mm of water per day. For hot tubs with a salt level up to 3000 ppm.
What causes a water leak in a hot tub?
Hot tub valves can be a possible leakage spot. There are various designs of hot tubs valves and the type of the valve determines what needs to be done for its repair. Such as, the knife look-a-like valves have two halves fastened together having a seal in-between which can fail and cause a water leak.
Can a hot tub leak be a real pain?
Having a leak in your hot tub can be a real pain, especially if you don’t know what you’re looking for and how to find it. Following a few simple steps, you should be able to find the source of the leak and be able to decide how to proceed with a repair, without a lot of headache.
How to drain, clean and re-fill your Sundance Hot Tub?
If your hot tub has Diverter Valves, turn them to the centre position. If your hot tub has air controls, turn them to the off position. Run Jet pumps for 2 hours (make sure all jets are running and have not been manually turned off). You will need to turn the jets back on every 20 minutes. You are ready to begin draining your Sundance Hot Tub.
For all types of spas, hot tubs, and pools. For leaks in walls, floor, housing, return lines, suction lines, skimmers, fittings, etc. For water loss in spa / hot tubs of less than 3 mm per day. For water loss in pools of less than 5 cm or 50 mm of water per day. For hot tubs with a salt level up to 3000 ppm.
What do you need to know about the Sundance spa?
As you surrender ot the warm, bubbly water of a Sundance® spa, you’ll be whisked away by the right blend of heat, buoyancy and massage that will change thehway you fee. Our patented Fluidix® jets were co-developed with Bowels Fluidics Corp, experts in the field of Fluid Dynamics.
How can I tell if my hot tub is leaking?
How to Detect a Hot Tub Leak. One common way to pinpoint where your leak is coming from, is to use dye or food coloring to color the water. Wherever you see dark water appearing first should indicate the leak location.
How to reset the timer on Sundance spa Aqua-Tech?
1. Press and hold the Jets pump 1 and Cooler button at the same time for 3 seconds. 2. Press the Warmer button until the display shows “0.” 3. If the counter has reached “0”, pressing the Jets pump 1 button will reset the timer. If the timer is not at “0” pressing the Jets pump 1 will not reset it.
Why is my Sundance Spa having trouble shooting?
1. Dirty Filter: even when you have cleaned the filter, the filter may be impacted and be time for a new filter. The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter.
What kind of circulation pump does Sundance Spa use?
Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.
What kind of pillow fits a Sundance 880?
Please enter a question. Fits 2009 to 2017 Sundance 880 Series Spas. Also known as 6455-484. Two tone pillow with ball socket connect on the back. Contoured for back of head comfort. Batteries Included?
Are there replacement headrests for Sundance cameo 880?
The old ones were disintegrating and kinda ick-ing me out. Replacement Headrests for Sundance Cameo 880 Spa. Our original headrests were falling apart. The paint-like surface was disintegrating on all of them and floating throughout the spa. Also the mount screw would no longer hold them in place.
How to replace the gasket on a Sundance spa?
Replacement Parts for Sundance Spa. 1 O-Ring/Gasket, Waterway 2″. Product ID: 711-4030. $1.50. $2.00. Add to Cart. 2 Barb Plug, 3/4″ Slip, Shur-Grip. 3 PTFE Tape, 1/2″ x 520″. 4 Barb Plug 3/4″ (For New Smartplumb Manifolds) 5 Gasket, 2″ Pump Union.
What should I use to re-fill my hot tub?
Using harsh cleaning products will result in foamy water when you re-fill your hot tub. A product such as The Tub Scrubber can be used to remove any residual waterline build up.
How much sun boom to add to hot tub?
After making any adjustments to the Alkalinity or pH (in that order) that are needed, you should add 1 Capful (30g) of Sun-Boom to the water, and boom! You’re ready to get your hot tub party on!
How often should I add Spa shock to my hot tub?
Spa Shock works together with Sun-Boom to maintain water clarity. Add 30ml (2oz) of Prevent II once a week to prevent stain, scale and calcium build up. When you are adding chemicals to your hot tub water, don’t add multiple chemicals at once. Your chemicals are more effective when they are added separately.
What should the hardness of my hot tub be?
The “Total Hardness” level (the bottom square on your test strip) is generally in the okay range unless you use a well to fill your hot tub or have a water softener system. If the water is too soft, use “Cal Rise” to increase levels.
How often should I add Sun boom to my hot tub?
Add Sun-Boom (30 grams / 1 Capful) as required (When the Total Chlorine reading on your test strips is at 0). Most people will add Sun-Boom 2-3 times a week (based on average use of 3-4 times per week).
What to do if your hot tub is low on power?
Many models require turning off the power for a few minutes and turning back on. For hot tubs powered by 240 volts, turn on the lower amp breaker. If your hot tub is 120 volts, unplug and re-plug after two minutes. Red and green blinking lights mean low water flow. Reset your spa by turning the power off and turn back on.
Why does my dead Spa have no power?
The greater disappointment is not being able to use the spa at that moment. If you’ve ever found a “dead spa” with no power, no indicator lights, nothing at all – this post is for you. Here, we outline the seven most common reasons that a hot tub has no power.
When did Sundance Spas start making hot tubs?
Sundance® Spas has been manufacturing hot tubs since 1979. They are based out of California, and their products are sold in more than 60 countries. Sundance® Spas focuses on creating acrylic spas, and they are rated as the top worldwide distributor and manufacturer of this particular style. They also produce in-ground and portable hot tub models.
What is the error code on the Sundance Spa hot tub?
Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.
When to turn off circulation pump on Sundance spa?
Allison from November 1st to April 31st you should run the spa in Standard mode with the Circulation pump set to run 24hr duration. Between May and November depending on the ambient air temperature you may experience overheat of the water especially in July and August.
What to do if your Sundance spa switch is defective?
Disconnect wires from Switch terminals. Set ohmmeter in the continuity position. Measure resistance across switch terminals for infinite resistance with pump off. If continuity is measured with pump off, the switch is defective. (Or debris blockage, l which you have to remove switch and inspect.
When adding new water to your Sundance hot tub, Put your hose into the filter well so that it runs through the pipes as it fills up, This will help prevent air locks upon re-start. Once your hot tub is filled, You can turn the power back on so it can begin heating up (Do not power up the hot tub until the hose has been removed).
Why does my Sundance spa go into Oh error code?
Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code
Why is my Radio not working on my Sundance 880?
After dropping the curtain to look for the flow switch (and giving it 2 power cycles) it came back to life. When it wasn’t running, flow switch open—closed once flow resumed. Ran spa for about an hour and all was well. After putting the right hand panel with the radio back together, I found the radio was not working.
What happens when Sundance spa goes into watchdog?
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.
