What kind of pump does Cal Spa use?

Pumps used by Cal Spas on their hot tubs, from different pump manufacturers. The Ultra Jet pumps are new Ultra Jet® pump components assembled on new high quality U.S. Motors or AO Smith/Century motors, and are replacement pumps compatible with Balboa Water Group® Ultra Jet® Pumps.

What should I do if my spa pump is not working?

Fill the spa with water level at 4 to 6 inches from the top. Open the gate valves. Noise may be a sign of damage or age. After you have tried all other troubleshooting, contact your dealer for service Let pump cool for an hour and try operating the spa for a shorter time Spa. Pump will reset automatically.

Why is the circ pump on my Sunrise spa not working?

If the circ pump is not operating it could produce the FLO message. A locked up pump could also cause the GFCI breaker to trip. The pump motor could need a new start capacitor or the motor itself could be on the way out. If all else fails contact your local Spa Service Support Desk to book a Diagnostic and Repair of your Sunrise Spa.

Can you operate a spa with the gate valves closed?

Never operate your spa with the gate valves closed! Fill the spa with water level at 4 to 6 inches from the top. Open the gate valves. Noise may be a sign of damage or age. After you have tried all other troubleshooting, contact your dealer for service Let pump cool for an hour and try operating the spa for a shorter time Spa.

Can a 2 speed spa pump be used?

One Speed Pump Configuration: A 2-speed spa pump can serve single-speed duty by using only the common and high speed terminal connections, while leaving the low speed terminal blank. *If your spa filtration or heating cycle comes on with high speed instead of low speed, this indicates that the high and low speed wires need to be switched.

What is the size of a spa pump?

Spa main pumps will have a size of either 48 frame, which are approx. 5.5” diameter, or 56 frame, which are approx. 6.5” diameter. Some motors will have the frame size on the unit.

How many amps does a 120 volt spa pump use?

Note that a 120 volt pump drawing 16 amps uses virtually the same amount of power (wattage) as a 240 volt pump drawing 8 amps. Spa pumps are available in two different frequency configurations: 50hz and 60hz. In North America, the line frequency is 60 HZ.

Spa main pumps will have a size of either 48 frame, which are approx. 5.5” diameter, or 56 frame, which are approx. 6.5” diameter. Some motors will have the frame size on the unit.

How many Cal spas swim pros are there?

We offer 6 different models in our Swim Pro™ line. Cal Spas Swim Spas X-Series combines our best models from the Swim Pro™ line and takes it to the next level of visual and ergonomic design with new features such as Elite™ cabinets, Cal Grip™, Cal Touch4 Control™ and Cal Armor™.

Which is the best pump for a hot tub?

Each switchless pump has a 50% thicker and longer shaft than standard pumps for increased durability and output. Shop for the perfect spa pump for your hot tub that will not only deliver an intense hydromassage, but will keep your spa water circulating for a clean and warm water spa experience.

What kind of pump does Cal flame BBQ use?

CAL FLAME BBQ PARTS By Brand: Select Pump Brand All Brands Artesian Be By Horsepower: Pick Horsepower Range 0 – 2 HP 2 – 4 HP By Cal Spas #: ContentPlaceHolder1_tbCalSpasPartNo By Waterway #: ContentPlaceHolder1_tbWaterWayPartNo

What’s the best replacement pump for Cal spas?

PRC603 spa replacement pump, PRC-603 Power Right spa pump replacement, 56F 2″ 1 speed 230v 10A for Cal Spas 3.1″ OD threaded connections. These are new Power Source pumps .. see full description replacement for PUUM2202582FR Spa Pump 230 Volt 8.0-8.8A 56 Frame Two Speed 2″SD/CS Cal Spas, PUUMC2202562FR, 1016010

Why is my Spa 2 speed pump not working?

II have a 2002 Optima spa. Several months ago the button on the top-side control panel for the 2 speed pump (#1) stopped working. There’s a second, smaller control panel on the opposite side of the tub which also will not work. But when the preset filter cycles occur the pump will come on and the icon comes on on the display.

What are the functions of the spa pump?

The Spa is recirc and temperature controlling correctly and the pumps are working during the daily auto cycle with an LCD icon on display. The main control panel looks fine (no misting), is backlit, the light buttons work correctly, but no other button functions are working (Temp, Pumps, Programming).

Can a DS pump run on low speed?

Below is a diagram of the correct and incorrect wiring of a DS pump. In the example above, the motor will only run at low speed when switched to high speed. If the wire from the H position on the switch is connected to HIGH and the L is connected to COM, the motor will only run on low speed.

What is the frequency of a spa pump?

Spa pumps are available in two different frequency configurations: 50hz and 60hz. In North America, the line frequency is 60 HZ. In Europe and elsewhere around the world it is 50 HZ. Some Island nations also use 60 HZ.

What to do if your hot tub pump is not working?

Because of the high cost of having a spa pump repaired by a technician, replacing it with a new Master Spas hot tub pump from Master Spa Parts will likely be your most economical option. Plus, Master Spa Parts typically ships same day if order is placed before 3pm CST, so you can have your hot tub up and running again in no time.

How does a caldera hot tub pump work?

In a Caldera Vacanza® Series spa, you’ll find the main pump that powers the jets and a circulating pump that maintains the water’s condition and temperature. Above both is a PVC pipe and a fitting (a union) that joins the pipes to the water pump.

What causes an air lock on a hot tub pump?

This situation is known as an “air lock”. When the jet button is pressed and the pump tries to prime itself and fill the plumbing and cavity around it with water, an air pocket may be trapped, causing water to not flow properly.

Is there a problem with my caldera hot tub pump?

This doesn’t mean that there’s an issue with the pump; it simply means that you’ll have to rule some things out to get to the root of the actual problem. As always when troubleshooting, have your Owner’s Manual handy. On Caldera Utopia® Series spas, the logo light serves as a helpful and visible diagnostic tool.

What to do if your hot tub pump has worn out?

If troubleshooting your hot tub pump doesn’t fix the issue, contact your local spa dealer for support. A hot tub service professional can perform a thorough hot tub pump check-up and diagnose each component of your spa. If your hot tub pump has worn out or has become damaged, a trained technician can replace it.

Is the hot tub at Cal spas safe?

Cal Spas is proud to offer our customers the highest quality, safest home resort products at the industry’s best prices. It’s arguably the most important part of your spa. It circulates your water while it heats up your hot tub. It helps create the blast of pressure that makes your jets so wonderful to enjoy!