What kind of power does a LRZ pool heater use?

The Legacy Model LRZ electronic heater gets electrical power from an external 120VAC or 240VAC source and provides a dual electronic thermostat control system for pool/spa combinations or preheat convenience.

What kind of pool heater does Zodiac use?

Consult Zodiac Pool Systems, Inc., or local factory representative, with any questions regard- ing this equipment. Certain sections of this manual are specific to either United States or Canadian installations, and are labeled as such. The Legacy model LRZ millivolt heater is a self contained standing pilot unit and requires no external power.

How to check your heater’s power to high limits?

Check wires to Fusible Link, replace Fusible Link. Correct excessive heat problem in cabinet. Possible rollout. YES STEP 8 –Check power to High Limits 24 VAC between Black (8) wire on PIB and Yellow (1) wire on Transformer? NO Recheck power at Blue (7) wire. If 24 VAC at Blue but not Black, replace PIB. STEP 9 Check thru High Limits

What should the water temp be in a Zodiac Pool?

Zodiac Pool Systems, Inc. offers the following recommendations to help conserve fuel and minimize the cost of operating your pool heater without sacri- ficing comfort. 1. The American Red Cross recommends a maximum water temperature of 78°F (25°C). Use an accurate pool thermometer.

What makes a Jandy pool heater so good?

Providing industry-leading engineering, Jandy’s innovative line of pool heaters and heat pumps are designed to deliver quality, energy-efficient heating solutions so you can enjoy a longer swim season in your pool. The perfect pool is neither too hot nor too cold.

Is the pool supply unlimited still working Jandy?

Jandy has quit the internet, but Pool Supply Unlimited is still working 7 days a week to get you the products necessary for a beautiful backyard oasis Parts for this item are available, click here.

Can a LRZ heater be used in a swimming pool?

The Legacy Model LRZ electronic heater is specifically designed for heating fresh water swimming pools and spas, and with proper installation and care, they will provide years of reliable service. Do not use the heater to maintain pool or spa water temperature below 70°F (21°C).

Jandy has quit the internet, but Pool Supply Unlimited is still working 7 days a week to get you the products necessary for a beautiful backyard oasis Parts for this item are available, click here.

How does the JXI pool and spa heater work?

VersaFlo Integrated Bypass Technology The JXi™ with VersaFlo is the first and only swimming pool heater that automatically directs the flow of water through the heat exchanger when heat is needed and around the heater when heating is not needed — allowing you to save money on the filtration pump electric bill.**

What’s the name of the pilot light on a gas heater?

Bad Thermocouple. The thermocouple is the co-pilot to the pilot light in electronic heaters. It senses when the flame of the pilot is hot enough to trigger ignition of the natural gas or propane that fuels the burner.

Why does my gas burner not light up?

Surface burners are often slow to light or will not light at all because the burner or burners are wet or dirty, the electrode is not seated properly, or because the burner head and cap are not matched up properly. Check the following if the unit has power but is not lighting.

When does the pilot flame go out on a gas furnace?

The intermittent pilot flame goes out after the heating cycle and remains off until the next time the thermostat calls for heat. The furnace gas valve for this type of furnace is identifiable with its solenoid designations: MV, PV, and PV/MV — where MV = main valve, PV = pilot valve, and PV/MV = common. Continue to 4 of 5 below.

Why does my water heater pilot light but not the burner?

If I understand correctly, your pilot flame is lighting correctly. But the main burner won’t turn on because the electronics in the Gas Control Valve don’t acknowledge the pilot is lit. There are two likely faults: Circuit Board in the Gas Control Valve is defective. To test for case 1, use a multimeter to measure the Thermopile output.

Why are the main burners not turning on?

Main burners did not turn on after a few minutes. I then tapped on the gas valve and what I think is a regulator a few times, and the main burners came on. I did not hear any valve open, but the flames were strong. The pilot light burns blue and strong the whole time.

Why does the standing pilot light not come on?

The standing pilot light is burning. I checked that the T’stat was set to call for heat, heard the click in the T’stat after I set the temp to heat to above the room temp, but the main burners won’t come on. This furnace was working fine earlier. I believe it might be a millivolt system.

What does it mean when your oil burner wont run?

If there is oil flowing freely at the oil line and all of the above check out, we suspect that the fuel unit is not pumping. No ignition: oil comes out of the nozzle but there is no ignition.

Can a legacy pool heater be used in a spa?

The Legacy heater is specifically designed for heating fresh water swimming pools and spas, and with proper installation and care, they will provide years of reliable service. Do not use the heater to maintain pool or spa water temperature below 70°F.

What did I do to my Jandy pool heater?

So I opened up our Jandy Legacy LRZ 399,000 to replace the insulation panels. While doing so I disconnected the unit to make examining the heat exchange easier. Once done trying to turn on the heat threw FAULT-CHECK IGN CONTROL.