What kind of error does Sundance certa 780 have?

My Sundance Certa 780 Series hot tub is showing an error of FL1. I went through the manual diagnostics and the error is still there. I contacted Aquatech and they suggested I clean the filter with the FilterBrite.

What are the manuals for the Sundance spa?

Find out how to use, care for, and program your Sundance ® spa by browsing the manuals and guides below. (2020) 880™ Series Manual – (Aspen®, Maxxus®, Optima®, Cameo®, Altamar®, Marin®, Cambria™, Capri®) (2020) 780™ Series Manual – (Chelsee®, Hamilton™, Montclair™, Bristol™, Hanover®, Dover™)

Is there an error code on my Sundance Hot Tub?

Why is my Sundance spa not flashing FL1?

If this does not correct the flashing FL1 msg you could have a blockage in the circulation line or at the flow or psi switch or you could have a bad connection at the flow or psi switch or a bad flow or psi switch. If all else fails contact our Service Support Desk to book a diagnostic and repair of your Sundance Spa.

When do I get FL1 flashing on my Sundance spa?

HI, I just plugged in my Sundance spa and I’m getting the code FL1 flashing. Even before I hit any buttons. When I go to turn pump 1 on both speeds work.

What happens when Sundance spa goes into watchdog?

When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.

What kind of circulation pump does Sundance Spa use?

Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.

How to set heating mode on Sundance spa 680?

Here are the instructions for setting the Heating Mode on your Sundance Spa. 680 Series: Press the “Menu” button repeatedly until you get to the “HEAT” menu. Use the temperature up or down buttons to scroll through heating options.

What’s the start time on a Sundance 880?

880 & 980 Series: Press the “Menu” button to enter the settings menu. Select “Heat & Filter”. Select “1” for Primary Filter. Adjust “Start Time” as required and press the check mark button to confirm and activate the setting. Select 12 AM if you are planning on using 24 hour filtration.

How big is the Chelsee 780 series hot tub?

Specifications Series 780 Seats 6 – 7 Dimensions 7’5″ x 7’5″ x 36″ (226 cm x 226 cm x 92 Spa Volume 520 US Gal (1,968 liters) Total Jets 40 Patented Jets (6 Varieties)

When did the Sundance microCLEAN filter come out?

This is the genuine Sundance product for Sundance 780 series spas built after about 2006. If your spa is older, check with your local dealer. Sundance tries to drive business for parts or refills to their retailers. This filter fit my Sundance 850 Series perfectly. The filter does what it’s suppose to do.

Why do I get an error on my Sundance Spa hot tub?

In the first 4 years we basically used one filter and never got this error message. Last year we bought 2 new filters and we switch between them so they are basically hardly used. Both filters have been cleaned in a tub overnight with FilterBrite. We have turned the hot tub off and on numerous times and tried both filters with no luck.

How many Sundance Spas are there in the world?

The Kingston™ delivers seating for 6-7 adults and delivers all the favourite features of Sundance® Spas hot tubs. Sundance® Spas can be found in more than 750 retails locations in 75 countries worldwide. Finding your nearest Sundance Spas dealer is easy! Use our store finder to find your local retailer.

When did the Sundance Spas 880 series start?

2007 880 Series �� 1

How big is a 2007 Sundance spa blower?

Hand Rails: 2 High quality stainless steel handles Rail: 6570-5, Grommets: 6540-65 (4) Filter: MicroClean Plus Filter 6540-507 or Standard Filter 6540-488 2 Year: 2007 Model:Optima Size: 89″ x 89″ x 37�5″ Series:880 Blower: 1hp 240V blower motor assembly 6500-148 Board:

What is the FL1 error code for Sundance spa Constance?

We have a Sundance Spa Constance (2011) and today also noticed the FL1 error code. In addition to the code, noticed that the pool is registering 72 degrees when it is set to 101. We have never had a problem with the hot tube, until now. We changed the UV bulb last summer and changed out the filters. Any assistance would be helpful.

What should I do with my 1998 Sundance 750?

Draining and Refilling ‘Economy Mode 29 30 30 31 31 32 32 33 34 .34 35 35 36 36 36 37 .37 38 38 40 42 44 Cleaning the Interior of the Hot tub. Pillow Care. Maintaining the Wood Cabinet. Maintaining the Cover …… Winterizing Restarting your Hot Tub in Cold Weather Water Maintenance. pH Control. Sanitizing.. Other Additives…

What are the instructions for the Sundance 850?

Programming Instructions Adjusting the Time of Day Changing the Filter Cycles Start Up Instructions 850 Models Operating Instructions 850 Models View Light.

Where can I Find my 1998 Sundance Hot Tub?

Locating Your Sundance Hot tub Tango Model Only A Tango model to be connected to 120V electrical service must be located close enough to a grounded. grounding type electrical outlet so that the power cord included can be plugged directly into it.

What kind of warranty does Sundance circuit board have?

This circuit board is brand new and carries a 6 month manufacturer’s warranty from the date of purchase. It can only be returned for warranty issues if installed.

2007 880 Series �� 1

How can I tell if my Sundance spa filter is defective?

The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation.

HI, I just plugged in my Sundance spa and I’m getting the code FL1 flashing. Even before I hit any buttons. When I go to turn pump 1 on both speeds work.

What is the error code on the Sundance Spa hot tub?

Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.

When did Sundance Spas start making hot tubs?

Sundance® Spas has been manufacturing hot tubs since 1979. They are based out of California, and their products are sold in more than 60 countries. Sundance® Spas focuses on creating acrylic spas, and they are rated as the top worldwide distributor and manufacturer of this particular style. They also produce in-ground and portable hot tub models.

How much does a Sundance 780 hot tub cost?

Starting at $9,960. The 780™ Series is designed to enhance your life. We combined new technologies with old-fashioned know-how to craft intuitive outdoor hot tubs that are a delight to use, with low profiles and a variety of seats to create the perfect backyard sanctuary. Explore All Models.

How many seasons are there of Sundance Spas?

2006 680 Series �� 30

How to contact Sundance spa for replacement filters?

Browse our latest guide showcasing all of our Spas. Call us at 1-844-602-6065 or submit a Contact Us request with any questions.

What kind of PWA does a Sundance Hot Tub use?

Compatibility Fits 1995 to 1999 two pump Sundance 850 Series Spas, Cameo, Optima, Altamar Features Black finish with Sundance logo. 1 ribbon connector to attach to the PWA. 1 ribbon connector for remote panel 3M strip included to secure panel to your spa shell.