What kind of controller does mastertemp heater use?
The MasterTemp heater also comes equipped with the Pentair multifunction temperature controller which shows, at a glance, the proper functioning of the heater. All MasterTemp heaters are designed with a direct ignition device, HSI (hot-surface ignition), which eliminates the need for a standing pilot.
When to turn off Pentair mastertemp 250 service heater?
Always make sure that the heater is off at least 10 minutes before the pump shuts off. Heat trapped in the heater increases the risk of scale. If you want a less aggressive chemistry towards copper I would suggest either using CLR or Lime-Away.
Is the Pentair mastertemp pool heater salt water?
MasterTemp Natural Gas heaters are designed to be quiet, they’re certified for low NOx emissions, and are eco-friendly, making them a dependable and safe heater for you and the environment. The 460732 is a standard unit, equipped with a copper heat exchanger making this unit not suggested for salt water.
Is the mastertemp pool and spa heater under warranty?
The MasterTemp pool and spa heater is sold with a limited factory warranty. Specific details are described on the warranty registration card which is included with the product. Return the warranty registration card after filling in the serial number from the rating plate inside the heater.
The MasterTemp heater also comes equipped with the Pentair multifunction temperature controller which shows, at a glance, the proper functioning of the heater. All MasterTemp heaters are designed with a direct ignition device, HSI (hot-surface ignition), which eliminates the need for a standing pilot.
What should the temp be on a Pentair mastertemp heater?
Display should change from water temp to exhaust temp. Normal temps should be in the range of 290-350. 350-500 is considered high and you should look for: Sooted exchanger (external) due to improper gas pressure or lack of proper venting. either supply of fresh air or exhaust, or both.
When did mastertemp high performance pool heater come out?
Pentair Water Pool and Spa StaRite and Mastertemp pool heaters manufactured between December 22, 2020 and January 6, 2021 recall. 4.7 out of 5 stars. Read reviews for MasterTemp High Performance Pool Heater This action will navigate to reviews. 5 out of 5 stars. I love installing mastertemps.
What does error code E01 mean on mastertemp 400?
MasterTemp 400 heater, when started, heats water for about two minutes, then shuts off and Service Heater light comes on with error code E01. On the circuit board, LED11 & J5 Temp-Fault lights are lit red. Thermistor was recently replaced. E01 is an indication that something is wrong with the temperature circuit.
When did Pentair replace the lid on their mastertemp heater?
For Heaters Manufactured after 1/12/09 (Clamp Lid Tub Design). For Heaters Manufactured After 11/16/13 (New 9-bolt lid tub design). This 6 pin board replaces the now obsolete 42001-0096S which was a 9 pin board.
Pentair Water Pool and Spa StaRite and Mastertemp pool heaters manufactured between December 22, 2020 and January 6, 2021 recall. 4.7 out of 5 stars. Read reviews for MasterTemp High Performance Pool Heater This action will navigate to reviews. 5 out of 5 stars. I love installing mastertemps.
MasterTemp 400 heater, when started, heats water for about two minutes, then shuts off and Service Heater light comes on with error code E01. On the circuit board, LED11 & J5 Temp-Fault lights are lit red. Thermistor was recently replaced. E01 is an indication that something is wrong with the temperature circuit.
When do you turn off the filter pump on a Pentair mastertemp?
A time clock controlling the filter pump should have a low-voltage Fireman’s Switch that switches off the heater at least 15 minutes before shutting off the pump. The “Fireman’s Switch” is a poor name for the 2 wire 24 volt AC remote control system of the heater.
What is the fireman’s switch on a Pentair mastertemp heater?
The “Fireman’s Switch” is a poor name for the 2 wire 24 volt AC remote control system of the heater. The Fireman’s Switch is a 2 wire control that can connect to automation such as the EasyTouch or IntelliCenter or to a timer. The current is less than 500 milliamps (0.5 amps).
How tall does a Pentair mastertemp gas heater need to be?
A natural gas or propane heater needs an optimum mixture of air and gas. If the air/gas mixture is incorrect you will have an orange yellow flame instead of a good blue flame. At higher latitudes the gas needs to be adjusted for the proper air/gas mixture. The Pentair Mastertemp is good to 9,000 feet.
How to troubleshoot a Pentair mastertemp pool heater?
Our Pentair Mastertemp Troubleshooting Guide starts with the error codes shared by both models, and follows into a 6 page flowchart to step by step troubleshoot a Pentair or Sta-Rite pool heater, and get it firing again fast! The burners on this type of MasterTemp/Max-e-Therm heater are quite unique from previous generation pool heaters.
The “Fireman’s Switch” is a poor name for the 2 wire 24 volt AC remote control system of the heater. The Fireman’s Switch is a 2 wire control that can connect to automation such as the EasyTouch or IntelliCenter or to a timer. The current is less than 500 milliamps (0.5 amps).
