What kind of circulation pump does Sundance Spa use?

Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.

What are the instructions for the Sundance 850?

Programming Instructions Adjusting the Time of Day Changing the Filter Cycles Start Up Instructions 850 Models Operating Instructions 850 Models View Light.

Where can I Find my 1998 Sundance Hot Tub?

Locating Your Sundance Hot tub Tango Model Only A Tango model to be connected to 120V electrical service must be located close enough to a grounded. grounding type electrical outlet so that the power cord included can be plugged directly into it.

What should I do with my 1998 Sundance 750?

Draining and Refilling ‘Economy Mode 29 30 30 31 31 32 32 33 34 .34 35 35 36 36 36 37 .37 38 38 40 42 44 Cleaning the Interior of the Hot tub. Pillow Care. Maintaining the Wood Cabinet. Maintaining the Cover …… Winterizing Restarting your Hot Tub in Cold Weather Water Maintenance. pH Control. Sanitizing.. Other Additives…

Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.

Why does my Sundance spa go into Oh error code?

Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code

What to do if your Sundance spa switch is defective?

Disconnect wires from Switch terminals. Set ohmmeter in the continuity position. Measure resistance across switch terminals for infinite resistance with pump off. If continuity is measured with pump off, the switch is defective. (Or debris blockage, l which you have to remove switch and inspect.

What to do if your Sundance Spa is having trouble shooting?

Very Important: DO NOT measure by placing your probe on L1 or L2 and the other probe on Ground, you will get a 120 Volt reading which is not correct. Continuity Test or Ohms test: Turn off the power to the spa and with your probe set to a continuity check, probe the 2 heater terminals at the same time.

What to do if your waterfall is not working?

One of the wall grates would be a prime candidate. Then fill the pump basket up as much as you can (it shouldn’t fill up) and put the lid back on it. Then run the pump and see if it primes. If it does, switch the valves on the “not sure” lines one way and then the other.

Why is my Sundance spa Flo not working?

If you ave one and the jets work, it’s even more likely that it’s a bad pressure switch. Good luck. If the circ pump is buzzing and hot to the touch most likely it is the culprit. If you can remove the equipment access panels, locate the flow switch to see if it is in the closed position or even moving/fluctuating.

What happens when Sundance spa goes into watchdog?

When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.

What does Flo code mean on Sundance heat pump?

I found it easily at the Sundance site online and keep a copy on my computer for reference. Nine times out of ten, a flo code means the pressure switch isn’t working, and ergo your circa pump wont work right, nor usually the heat. It’s a cheap part and won’t take a repair guy more the 20 minutes to fix.

What’s the wet end on a Sundance pump?

Complete Wet end for Sundance Spas Emerson 48 Frame motors used up to 2009. Contains front and rear housing, impeller, o-ring, seal and screws. Comes fully assembled. SUNDANCE SPAS wet end for 1.5 Hp Pump. Can be used on all SUNDANCE SPAS Pumps from 1998-2004/2009. 2 inch Suction and Discharge. (3 inch OD). 48 Frame.

When do I need to replace my Sundance spa pump?

New Pump Replacement for SUNDANCE SPAS Palermo 2000-10/2002. Has the old style welded foot on the motor. Click MORE INFO for applications.

Why does my Sundance spa not heat up?

It sits 3. I have noticed that that I have a constant FLO error, and the water will NOT heat unless the jets are running. I also believe that my circulation pump is causing these issues. It buzzes and is warm to the touch, but I can’t feel the water moving at all. I just don’t think it is working properly.

What are the replacement parts for a Sundance spa?

In this section you will find all replacement spa parts that we stock for Sundance Spas including Air Blowers, Circuit Boards, Heaters, Pumps, Covers, Ozonators, Control Boxes, Pillows, Jets, Filters, Topside Control Panels and many others.

How can I tell if my Sundance Spa is having problems?

The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation. Is there voltage going to pump, Is there adequate Flow coming out of Heater Port in Spa?

What kind of circulation pump do I need for my jacuzzi?

If you are still having trouble trying to determine exactly what part you need for your hot tub, then please get in touch or if you simply want more information, you can contact us by email or call us. Sundance Spas specific circulation pump that comprises of a 2″ XP2 wet end and Aqua-flo Circ Master motor.

Can a Sundance pump be used with an Emerson pump?

Sundance® Spas LX 56 Pump. These are the newest Pumps from Sundance® Spas. The components are NOT interchangeable with the Emerson 56 Frame or Aqua-Flo Pump/Motor.

Redesigned 240v Circulation Pump $295.00 $199.00 Redesigned Circulation Pump For Jacuzzi® Hot Tubs & Sundance® Spas 6000-125NA OEM 230/240v circulation pump for select Jacuzzi® & Sundance® Spas. This new style pump is OEM equipment designed…

What to do if your Sundance spa heater is not turning on?

Heater is deactivated and pump may not turn on. Flow/pressure switch is defective. These steps should only be taken after checking and testing the above steps. With the circ pump and the main pump off, test switch operation with an ohmmeter in the continuity position, test for continuity across switch terminals.

Why is my Spa 2 speed pump not working?

II have a 2002 Optima spa. Several months ago the button on the top-side control panel for the 2 speed pump (#1) stopped working. There’s a second, smaller control panel on the opposite side of the tub which also will not work. But when the preset filter cycles occur the pump will come on and the icon comes on on the display.

What to do if your circ pump is not working?

Check that your power is on, the breaker or GFCI test button are not tripped, all valves are in the open position. Follow the circ pump plumbing, and look for any kinks in the hose.

How often should I Run my Sundance spa circ pump?

Most people run your Series of Sundance spa in Standard mode with a 24hr circ pump run time 12 months a year. Setting it up this way and always having a clean micro filter lessens the chance of the water chemistry and water clarity getting away on you.

What are the circulation settings on Sundance spa?

Currently it is set on “Standard Mode” and continuously runs. In my previous residence I had an Arctic Spa that was set to circulate intermittently. I have the manual and see how to change the circulation time/durations but wanted to know what was recommended by the professionals before changing anything.

How long does a Sundance Spa hot tub last?

The hot tub is programmed with a default setting starting at 12:00 AM and lasting for 8 hours, but this can be changed. This cycle addition to the normal operation. filter cycle. For example, the primary filter cycle is set to 8 hours every water after the cycle has finished. The next primary filter cycle will only be for 6 hours not 8 hours.

When did the Sundance jacuzzi pump come out?

This new style pump is OEM equipment designed… 2002-2006 2 SPEED JACUZZI® & SUNDANCE® 240V THERAMAX PUMP 6500-343 Original style Jacuzzi Theramax pump/motor assembly with fixed moutning bracket. Fits all years but originally used from 2002-2006.

What is the error code on the Sundance Spa hot tub?

Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.

Is the Balboa hot tub circuit board obsolete?

This Balboa Circuit Board, HS200M7 Digital, 53864-01 is OBSOLETE. See generic replacement 52320, or consider a new replacement controller that comes with a new heater, topside panel and cords. This Balboa Circuit Board, PHX15 Digital, 52941-01 is OBSOLETE.

What is the circuit board for hot springs?

Hot Springs/Watkins Secondary Circuit Board, for IQ2020 System, 2001-2008 Model, onboard 2 Heater Relays. OEM part number 77119. This Heater Relay Board Retrofits into IQ-2020 and Advent

How old should a Spa circuit board be?

If you need a spa circuit board that is not listed here, contact us for availability and pricing. If your spa controller is more than 3 years old, we recommend replacing the spa controller rather than just the circuit board. Circuit boards that have worked for a couple of years tend not to go bad just by themselves.

Sundance® Spas LX 56 Pump. These are the newest Pumps from Sundance® Spas. The components are NOT interchangeable with the Emerson 56 Frame or Aqua-Flo Pump/Motor.

What does the Sundance Chelsee seat do for You?

UV-resistant synthetic cabinetry with tool-free EZ Access Door makes maintenance a breeze. This opens in a new window. Deep-tissue pressure makes pain and tension from your neck to your calves fade away. This series-exclusive seat is designed to banish fatigued muscles, stress and tension.

What kind of pump do I need for my jacuzzi?

Components for the Jacuzzi® Spas, Sundance® Spas Theraflo, Theramax Pumps. 06/2009+ 48 Frame (Emerson) Pumps. For parts and pieces Click Here! For Complete Pumps please check out the lower section of this page.

What are the dimensions of a Sundance Optima spa?

The Sundance Optima Spa has an overall height of 37.5” (95.3 cm), width of 89” (226.1 cm), and length of 89” (226.1 cm). It seats 6-7 people and has a total volume of 410 gal (1552 L).

What do you need to know about Sundance maxxus?

Additional factory installed layer of insulation between the frame and siding of the spa to conserve heat in the coldest climates. Plus, upgraded spa cover designed for cold, harsh climates. 4. Professional Delivery & Installation Required (Additional Cost) Please consult with your local dealer about professional delivery and installation services.