What kind of circuit board do I need for a hot tub?
1. Balboa M7 Circuit Board: The reading across the two pins where both the “A” & “B” sensor plug in should read .5 volts DC. 2. Gecko Circuit Board: If you have three flashing dots on the display and there is a red light illuminated on the circuit board then the high limit sensor needs to be replaced.
When to replace a gecko hot tub circuit board?
Gecko Circuit Board: If you have three flashing dots on the display and there is a red light illuminated on the circuit board then the high limit sensor needs to be replaced. If the red light is not on, then there is a flow issue or faulty pressure switch. See “error codes/blinking dots” above. 3.
What should the temperature be on a circ pump?
The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. Over heat. The spa is at a temperature above 108° . Do not use spa when temperature is flashing or the OH message is displayed. Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.
What should the voltage be on a hot tub circuit board?
If you DO have 220 volts across both hot wires coming from the house, then next measure the voltage across both heating element pins. You should see 220 volts. If you do not, then the circuit board is faulty and will need to be replaced or sent to us for repair.
What kind of circuit boards are used in radios?
PCBTF100F, PCBF1, PC560 Printed Circuit Board, Used in Final PA of Atlas Radios, PC501 Printed Circuit Board, Used in Final PA of Atlas Radios, PA10-70B KLM Amplifier Plan Set w/ Circuit Board, Schematic, and Parts list. (10w input / 70 watt output), PC500E Atlas 210X / 215X Printed Circuit Board, Used in Final PA of Radio,
Gecko Circuit Board: If you have three flashing dots on the display and there is a red light illuminated on the circuit board then the high limit sensor needs to be replaced. If the red light is not on, then there is a flow issue or faulty pressure switch. See “error codes/blinking dots” above. 3.
Why does my hot tub keep Tripping the circuit board?
If the GFCI holds, then you have found the cause of the GFCI tripping. It will need to be replaced. If you have everything unplugged (including the main pump) and it still trips, then there may be an issue with the transformer that is soldered or plugged into the circuit board. If the transformer plugs into the board it can be easily replaced.
How to troubleshoot a spa control panel problem?
Reset the control panel if it only displays dashes and not error messages. Turn the power off for one hour and then turn it back on. If the control panel is displaying strange messages or have lights blinking at the same time, it could be a software issue with the circuit board. Check if there is corrosion or condensation.
What to do if your hot tub pressure switch is defective?
To check to see if the pressure switch is defective or miscalibrated, please do the following: Power down the circuit board. Unplug the pressure switch cable from the circuit board, thus revealing two pins. Power up the system. As soon as the low/filter pump turns on, jump the two pressure switch pins on the board with alligator clips.
What is the error code on the Sundance Spa hot tub?
Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.
What to do if the main pump is off in Sundance spa?
If debris is present, remove debris, install switch and test system. If condition still exist, replace switch.) if switch measures infinite (no continuity) with pump off, switch is OK, Turn on Main pump and measure across switch terminals for continuity. If continuity is measured, switch is OK.
How can I tell if my Sundance spa filter is defective?
The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation.
What are the error codes on the Balboa spa?
Balboa Spa Side Error Codes pd Power supply, unit running on battery ba OH Sensors reading 112-118° F. OHH Overheat. Spa has shut down. One sensor OHS Overheat. Spa has shut down. One sensor
