What is the error code on the Sundance Spa hot tub?

Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.

When did Sundance Spas start making hot tubs?

Sundance® Spas has been manufacturing hot tubs since 1979. They are based out of California, and their products are sold in more than 60 countries. Sundance® Spas focuses on creating acrylic spas, and they are rated as the top worldwide distributor and manufacturer of this particular style. They also produce in-ground and portable hot tub models.

What to do if your Sundance spa switch is defective?

Disconnect wires from Switch terminals. Set ohmmeter in the continuity position. Measure resistance across switch terminals for infinite resistance with pump off. If continuity is measured with pump off, the switch is defective. (Or debris blockage, l which you have to remove switch and inspect.

Can a hot tub circuit board be replaced?

Circuit boards that have worked for a couple of years tend not to go bad just by themselves. Instead, something has caused them to go bad. And whatever that is, it’s not being fixed by replacing the circuit board. Consequently, the life expectancy of a replaced circuit board is less than that of a new spa controller.

How big are the control panels at Sundance spa?

Sundance Spa Control Panel 6600-038 SMT System 2 Pump 6600-038 or SUN6600-038 Control panel is about 10 1/8 inches wide and 3 1/8 inches high. shows 6 buttons including Temp up, Temp down, jets 1, jets2, light and mode. Sundance Spa 2 Pump SMT System… Sundance Spa control panel SUN6600-425 as used in 880 Series spas (2013-2014).

Are there control panels for a hot tub?

Sundance Spas control panels for hot tubs are on sale at Hot Tub Outpost. We offer fast shipping and great prices on Sundance Spas 400, 600, 650, 700, 750, 800, 850, 880 series control panels, We also offer Sweetwater 680, 780,850E Portofino control panels as well as the newer I-Touch and programmable controls.

What happens when Sundance spa goes into watchdog?

When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.

What to do if the main pump is off in Sundance spa?

If debris is present, remove debris, install switch and test system. If condition still exist, replace switch.) if switch measures infinite (no continuity) with pump off, switch is OK, Turn on Main pump and measure across switch terminals for continuity. If continuity is measured, switch is OK.

What causes Flo error message on Sundance Altamar spa?

I have a Sundance Altamar spa, and I’ve occasionally had that FLO error message too in the past. If I recall it might have been caused by air in the lines (not filling tub properly?) or possibly from obstruction. I had one of the small cotton intake covers get sucked into pipes before.

How can I tell if my Sundance Spa is having problems?

The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation. Is there voltage going to pump, Is there adequate Flow coming out of Heater Port in Spa?

How to turn off heater on Sundance spa Aqua-Tech?

Activate the spa’s air blower and let it run for approximately 30 seconds.” I looked at the heater on my 2013 Sundance Optima and I don’t see any switch or plug to turn off the heater. Is it OK to turn the power breaker back on for 30 seconds with an empty tub or can you tell me how to shut off the heater?

Is the Sundance Optima a well insulated spa?

The Sundance Optima is a very well insulated spa. You still may gain some heat just because of the insulation but reducing your filter pump and circ pump cycles and keeping the spa in Economy will keep down heat that you may gain kinetically from the pumps.

How to turn off heater on Sundance Optima?

One step says: “Next, locate your spa heater, and turn it off. … Activate the spa’s air blower and let it run for approximately 30 seconds.” I looked at the heater on my 2013 Sundance Optima and I don’t see any switch or plug to turn off the heater.

How can I tell if my Sundance spa filter is defective?

What are the error codes on the spa side?

Flow Switch (heater is deactivated. Pump may also be deactivated). Panel sensors have been pressed too many times in a short period of time. Circuit Board temperature has exceeded acceptable limit. Freeze protection. No action is necessary. Freeze protection. No action is necessary. Communication between the panel and circuit board is faulty.

What do you need to know about SPA will not heat?

NOTE: If you have a Printed Circuit Board (PCB) in the main control box please click here for circuit board troubleshooting. The information below is for mechanical control boxes, without circuit boards. “My spa will not heat” is the number one complaint we hear, it accounts for almost every repair that is sent in to Spa Care Center.

What do you need to know about Sundance spa?

We have Sundance, Spas, parts, pillow, control panel, circuit board, parts, Sundance Spa pumps, Sundance Spa circuit board, Sundance Spa pcb, Sundance Spa pillows, Sundance Spa filters, Sundance Spa heaters, Sundance Spa control panel, Sundance Spa touch pad, Sundance Spa controller, Sundance Spa motor, Sundance Spa parts, filumps, sensors.

What does summer logic mean on a Sundance spa?

These are the error codes and display messages that a Sundance® Spa may display, along with what they mean and any actions required: “Summer Logic” occurs when the actual water temp for the spa climbs to 2°F (1°C) above set temperatures and is more likely in extremely hot weather.

Why do I get an error on my Sundance Spa hot tub?

In the first 4 years we basically used one filter and never got this error message. Last year we bought 2 new filters and we switch between them so they are basically hardly used. Both filters have been cleaned in a tub overnight with FilterBrite. We have turned the hot tub off and on numerous times and tried both filters with no luck.

Do you need a cover guy for a Sundance spa?

If you are needing a replacement hot tub cover for your Sundance® Spa The Cover Guy is your answer. With all Sundance® Models on file The Cover Guy can easily provide you with a new hot tub cover without you having to measure.

What to do if you have an airlock on your Sundance spa?

Remove your filter and stick the garden hose in that hole with a rag wrapped around it to force water into that line and hopefully alleviate a potential airlock. Alternatively you could locate the suction line where it is attached to the circulation pump, loosen the gear clamp and the hose and bleed the airlock from there.

What is the FL1 error code for Sundance spa Constance?

We have a Sundance Spa Constance (2011) and today also noticed the FL1 error code. In addition to the code, noticed that the pool is registering 72 degrees when it is set to 101. We have never had a problem with the hot tube, until now. We changed the UV bulb last summer and changed out the filters. Any assistance would be helpful.

What do you need to know about the Sundance spa?

As you surrender ot the warm, bubbly water of a Sundance® spa, you’ll be whisked away by the right blend of heat, buoyancy and massage that will change thehway you fee. Our patented Fluidix® jets were co-developed with Bowels Fluidics Corp, experts in the field of Fluid Dynamics.

Why is my spa control panel not working?

Reset the control panel if it only displays dashes and not error messages. Turn the power off for one hour and then turn it back on. If the control panel is displaying strange messages or have lights blinking at the same time, it could be a software issue with the circuit board.

What kind of circulation pump does Sundance Spa use?

Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.

Who is the owner of the Sundance spa?

Our patented Fluidix® jets were co-developed with Bowels Fluidics Corp, experts in the field of Fluid Dynamics. Discover how you can enjoy the next generation of spa ownership, making it easier than ever to use and maintain your Sundance® spa.

What kind of error does Sundance certa 780 have?

My Sundance Certa 780 Series hot tub is showing an error of FL1. I went through the manual diagnostics and the error is still there. I contacted Aquatech and they suggested I clean the filter with the FilterBrite.

How long can I go without pain at Sundance spa?

After 20 min a day I can go without pain for 1-2 hr.” Schedule a site design consultation with a certified expert. Test out your spa of interest with a private wet test. Browse our latest guide showcasing all of our Spas. Call us at 1-844-602-6065 or submit a Contact Us request with any questions.

Is it normal for hot tub to not heat up in summer?

During the summer, it may not be a big problem: many people will keep their hot tubs at 80 or 90 degrees to use like a swimming pool. Just make sure you get it taken care of before winter.