What is the error code for the spa?

PSoL = Pressure switch open with low pump. PSoH = Pressure switch open with high pump. ToE = Time out error. Rare system error. Spa unusable. Contact ACC. OHH = Overheat. Spa has shut down. One sensor has detected 118º Fat heater. OHS = Overheat. Spa has shut down. One sensor has detected 110ºF. SnA = Spa is shut down.

Are there any error codes for a jacuzzi?

Hence the need for a BIG LIST of CODES. The alphabetical list of hot tub error codes below covers all major manufacturers of spa controls, including ACC, Balboa, Brett Aqualine, CTI, Dream Maker, EasyPak, Gecko, Hurricane, Jacuzzi, Len Gordon, Maax, Pinnacle, Spa Builders Group, Spa Quip, Sundance and Vita Spas.

What are the spa side error codes for gecko?

Gecko Spa Side Error Codes FLO Pressure switch failure, switch open FLC Pressure switch failure, switch closed Prr Temp sensor failure Prh Hi-limit sensor failure HL Sensor measuring 119 degrees

Why is the sensor on my artesian spa not working?

The sensor plugged into sensor “A” jack is malfunctioning. Contact the dealer or service company if you continue to see this problem. Keep in mind this error may display itself temporarily also in situations of overheating. It should disappear when the heater cools off. Means that the sensors are not in balance.

Is there an error code on my hot tub?

Below is a list of common error codes from the top manufacturers of control equipment for hot tubs. Note: The control system brand name is usually different from the hot tub brand name. You can often determine the make of the control system by looking inside the spa’s equipment area.

What causes the spa side error code to go away?

Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. Shut the spa down, remove the filter and make sure all the jets are open. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

Why do I get error messages on my Master Spa?

For the error messages of HFL, LF, Dr, or DRY. This means that there is a flow issue through your heater. Try and clean your filters. While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump.

Why are there error messages on my artesian hot tub?

Some of these can indicate that you have a fault. Others will display operational messages to ensure optimal usage of the hot tub. There are six different ranges within Artesian Spa. They may display different codes. These ranges are: Download the full owner’s manuals here.

Why do I keep getting the F1 error code?

If the F1 error is gone, this could be due to the removal of the blockage or simply because of the restart of the machine. If you are still getting the F1 error code, the cause of the problem could be the control board, so check out our next repair technique.

Which is the correct spa code for PSOL or psoh?

PSoL = Pressure switch open with low pump. PSoH = Pressure switch open with high pump. ToE = Time out error. Rare system error. Spa unusable.

What should I do if my Master Spa wont reset?

One of the sensors detected 118°F at the heater. Remove spa cover and let the water cool down. After the water has cooled, push any button to reset. If the spa doesn’t reset there is an issue with sensors onPC board. Find replacement PC board

How often does a Master Spa hot tub filter?

Your hot tub is only scheduled for filter 2 times a day for 2 hours. This may cause your water temp to not be at what you have it set at. The hot tub is in Sleep mode. While in Sleep mode your hot tub will filter 2 times a day for 2 hours a piece. Your hot tub does NOT heat during this time in this mode. The hot tub is in Standby mode.

What does it mean when your Master Spa says dry?

A substantial difference between the temperature sensors was detected. This could indicate a flow problem. For the error messages of HFL, LF, Dr, or DRY. This means that there is a flow issue through your heater. Try and clean your filters.

What does EC stand for on a hot tub?

The “EC” stands for Economy mode, which in this mode does not allow the heater to heat up all the way. There are 3 different modes, Economy (EC), Sleep (Sl) and Standard (St).

What does cover guy on Vita spa stand for?

The Cover Guy provides all Vita Spa replacement covers so you are guaranteed a perfect fit every time. These are the error codes and display messages that a ThermoSpas Hot Tub may display, along with what they mean and any actions required: Stands for “Overheat”- and the tub shuts down.

What’s the phone number for a Vita spa?

Call us at (805) 654-9000 to set up a private appointment. The steel sub-structure used in Vita Spa’s 700 and 500 Series has the highest strength to weight ratio of any building material available.

How long has the Vita spa been around?

For over 30 years, Vita Spa has been synonymous with quality, comfort, and innovation. It’s called Hydrotherapy, and it’s at work in a Vita Spa. Hop in, shift gears and just let the world stand still for awhile.

Why does my Vita spa not turn on?

Overheating condition where a water temperature sensor has detected water temperatures of 110°F (43.3°C). Spa functioning is then disabled until temps fall below 108°F (42.2°C).Could indicate a pump operating at low speed for an extended time, constant filtering due to a programming error or a faulty pump. DO NOT GET INTO THE WATER!

What is the error code on the Sundance Spa hot tub?

Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.

What to do if your spa has an EO2 error?

Reset, test, reset (If your pump has a have PRCD). Debris screens can become blocked especially in hard water areas due to calcium build-up. Step 2: Empty the spa fully of water and place a running hose inside the pipes. Repeating from outside and inside the spa. Step 4: Restart pump. Reset, test, reset (If your pump has a have PRCD).

Why is the power button on my spa not working?

If you do not hear anything when the button is pressed the button may not be working. First cut off the power to the spa, then locate the electrical box inside the spa, it is normally located under the controls.

What is the lazy spa error code E02?

If you are curious about what is Lazy Spa E02 and how to fix Lazy Spa Error Code E02? Here is your answer This is an error code which displays on the control panel of Lay z Spa due to lay z spa pump problems. Here are some common Reasons Why Lazy Spa E02 And Lazy Spa E08 occur:

What does it mean when your spa sensor is out of balance?

Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. Substantial difference between temperature sensors detected. Could indicate a flow problem. Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours).

How to troubleshoot Lay z spa pump error codes?

Lay Z Spa pump Troubleshooting with error codesE01 : Unplug the pump. With one hand hold the pump and with the other hit the pump three times strong enough t… Lay Z Spa pump Troubleshooting with error codesE01 : Unplug the pump.

PSoL = Pressure switch open with low pump. PSoH = Pressure switch open with high pump. ToE = Time out error. Rare system error. Spa unusable.

Is there an error code for Leslie’s pool?

Leslie’s is proud to partner with Hot Tub Works to bring you this helpful content on lesliespool.com. The best thing about digital spas and hot tubs – those with a spa side control panel – is that you are given error codes for most equipment problems.

What are the error codes on the spa side?

Flow Switch (heater is deactivated. Pump may also be deactivated). Panel sensors have been pressed too many times in a short period of time. Circuit Board temperature has exceeded acceptable limit. Freeze protection. No action is necessary. Freeze protection. No action is necessary. Communication between the panel and circuit board is faulty.

Why is my spa not showing up on my computer?

If display shows only this message (blinking) spa is shut down Multiple causes; open sensors, bad connection to panel, improper voltage, etc. Time out error. Rare system error. Spa unusable.

Is there a problem with my caldera hot tub pump?

This doesn’t mean that there’s an issue with the pump; it simply means that you’ll have to rule some things out to get to the root of the actual problem. As always when troubleshooting, have your Owner’s Manual handy. On Caldera Utopia® Series spas, the logo light serves as a helpful and visible diagnostic tool.

What to do if your hot tub has a flow sensor error?

1. I am getting a Flow Sensor Error. Solution 1: If you get a flow sensor error on your hot tub, you will want to turn off your spa. Make sure your spa is full. Then you will want to pull out the filter and put the hose in the hole. Turn the hose on full blast for about 25 seconds.

What does the diagnostic logo light on caldera Utopia mean?

On Caldera Utopia® Series spas, the logo light serves as a helpful and visible diagnostic tool. When the diagnostic logo light shines orange and gray, the spa water is within 2° Fahrenheit of the set temperature and ready to enjoy. When the spa senses an issue, the diagnostic logo light may turn off, blink, or the colors may flash independently.

How to reset spa message on calspas.com?

Press any button to reset or wait 15 minutes and spa will automatically reset. If message spa does not reset, call customer service. Insufficient water detected in heater. Spa is shut down. (Displays on third occurrence of dr message.) Follow directions for dr message and press any button to reset spa.