What happens when the Dometic thermostat is locked out?
Shorted Indoor Temperature Sensor. All heat, cool, and dehumidify operation will be locked out. Manual fan operation will continue. Open circuit or out of range Outdoor Temperature Sensor (select models). Heat pump and dehumidification operation will be locked out. Air conditioner, furnace, heat strip and fan operation can continue to operate.
What does the error code E1 mean on the Dometic thermostat?
Error Code: E1 Results from a loss of communication between the Single Zone LCD thermostat and its module board. LCD will cycle between E1 and the previous mode setting. The system eventually shuts down. E2 Open circuit or out of range Indoor Temperature Sensor.
Is the Dometic CT thermostat control kit safe?
The Dometic CT Thermostat Control Kit can control your Dometic heating or cooling appliances. WARNING This product can expose you to chemicals including arsenic, which is known to the State of California to cause cancer. For more information, go to
How to troubleshoot a Dometic thermostat error cone?
Dometic 3313192 Thermostat Troubleshooting. Error cone. Solution. E1. Loss of communication between the Single Zone LCD thermostat and the module board. LCD will cycle between E1 and the previous mode setting. System will shut down. E2. Open circuit or out of range Indoor Temperature Sensor.
How to wire a Dometic 3 thermostat and control kit?
For two unit installations: Install one unit 1/3 and . set of thermostat wires to the second unit. .. CCC 2 Electronic Control Kit Wiring Diagram. Dometic Corporation 46 Zatonski, Unit 3 .
What happens if the Dometic thermostat is out of range?
Loss of communication between the Single Zone LCD thermostat and the module board. LCD will cycle between E1 and the previous mode setting. System will shut down. Open circuit or out of range Indoor Temperature Sensor. Heating and cooling operation will be locked out. Fan operation can continue to operate. Shorted Indoor Temperature Sensor.
Error Code: E1 Results from a loss of communication between the Single Zone LCD thermostat and its module board. LCD will cycle between E1 and the previous mode setting. The system eventually shuts down. E2 Open circuit or out of range Indoor Temperature Sensor.
What’s the setting for the Dometic single zone thermostat?
For a Dometic Single-Zone Thermostat, here’s how. Press the + or – button so that the setting changes from “Hi” (High) or “Lo” (Low) to “Au” (Auto). Note: If additional indoor air circulation provided by the air conditioner is not desired during Furnace Mode of operation, select Au (AUTO) in the Fan Mode to shut the air conditioner fan off.
How does the Dometic a / C cycle work in the winter?
It will reverse the freon and blow warm air in the summer and cold air in the winter to melt the ice on the coils. There is a temperature sensor that controls this, This topic is now closed to further replies. Honda generator fail! Poor Honda quality! OMG!
Can you put a new thermostat on an old Dometic unit?
You can’t go to the new thermostat unit with a ducted unit without changing all air conditioners and heat pumps, since they are incompatible. If you have an old 4 or 5 button thermostat, you can’t just put in a new Dometic unit.
How long does a Dometic RV air conditioner last?
Dometic’s commercial grade rooftop air conditioners are performance-tested to overcome harsh or unusual road and weather conditions. Many standard units break down after just four hours of extreme vibration testing, while the Brisk II is still going strong at 30 hours and more!
What to do if your Dometic heater is not working?
1. Clearing communications issues: your unit can get into a situation where the thermostat is not communicating with one or both upper boards. Turn the thermostat off, and turn power to the AC units off and on. Then turn the thermostat on and see if it works better. 2. Reset the thermostat to factory specs.
It will reverse the freon and blow warm air in the summer and cold air in the winter to melt the ice on the coils. There is a temperature sensor that controls this, This topic is now closed to further replies. Honda generator fail! Poor Honda quality! OMG!
Why is my Dometic air conditioner not cooling?
Outer temperature is too low or all air nozzles are closed. The roof air conditioner is not set to cooling. Set the roof air conditioner to cooling. The ambient temperature is above 52 °C.
What should the ambient temperature be for a Dometic air conditioner?
The ambient temperature is above 52 °C. The roof air conditioner is only designed for ambient tempera- tures of up to 52 °C. The temperature set is higher than the room temperature. Select a lower temperature. The ambient temperature is below 16 °C. The roof air conditioner is only designed for ambient tempera- tures above 16 °C.
What happens if your Dometic thermostat goes down?
Furnace, heat strip, heat pump and fan mode of operation can continue to operate but displays the last temperature set-point. Loss of communication between the CCC 2 thermostat and all system power module boards. System will shut down. Loss of communication between the CCC 2 thermostat and an individual system power module board.
Why is my CCC 2 thermostat not working?
Loss of communication between the CCC 2 thermostat and an individual system power module board. The LED will display error code El and the zone number that lost communication. Any additional zones that loose communication will blink in addition to the current zone. Open circuit or out-of-range indoor temperature sensor.
